Panasonic Ventilating Fan Fv 05vk1 Installation Instructions

Ventilating Fan
READ AND SAVE THESE INSTRUCTIONS.R
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
FV-05VK1
FV-08VK1
Table of Contents
Description
Dimensions32
2
Supplied Accessories
Wiring Diagram4
Specifications
13
14 6-84
54
Unpacking
General Safety Information
12VInstallation( Wooden Header )...

FV-05VK1
FV-08VK1
1 81Thumb screwLong screw
(M4X30)Quantity Appearance
Part name
Suspension
bracketII1
1
Suspension
bracketIII
Grille
Screw
(M4X10)II2
2Screw
(M4X8)I
These Panasonic ceiling mount ventilating fan models use a sirocco fan with dolphin-shaped blades driven by
brushless direct current motor. The motor is designed to have long operating life,high dynamic response,higher
speed ranges with saving energy. Double orifice technology is used to reduce noise. The grille covering the
main body is a...

Damper Fan bodyAdaptor
Grille
Part name Part name
No.
No.
1
2
3
46
7
8
Suspension bracketOrifice
Orifice cover Bracket cover
59
10Junction box cover
Junction box
Unit: ( )inches mmFV-05VK1
FV-08VK1
(For 16 inches on center joists, only use suspension bracket , for 19.2 inches on center joists, only use
suspension bracket , If more than 19.2 inches on center, use suspension bracket & .)I
III II III
9 1
102
37/8 98()
7
3
13 330()
10 1/4 261( ) 3 1/2 (90)
10 1/4 261()
12 1/8 (307)
12
37/8 98()
7
3
6
13...

Unpack and carefully remove unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
HzV Air direction Model No.(W)
Power consumptionSpeed
(rpm)Air deliver at
0.1 WG (cfm)Weight
kg(Ib.)
Duct
diameter
(inches)Noise
(sone)
FV-05VK1
FV-08VK16.0 666 506.0 (13.2)

CAUTION:
1. For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig .B)
3. This product must be properly grounded.
45o45o
Floor
Do not install above or(Cooking area)
inside this area
equipmentCooking
Fig. B
WARNING:
To reduce the risk of fire, electric shock or injury to persons, observe the following;
A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact
the manufacturer.
B....

1. Before installation, open the orifice cover. Secure the fan
body to adaptor by using thumb screw. (Fig.1)
Fig.1
Fan body
Thumb screw
Orifice cover
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketISuspension
bracketIII
Suspension
bracketI
Fig.2-1
Fig.2-2
Fig.2-3
Fig.2-4Fan body
Fan body
Fan body
Fan body
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketII
6
Remove the tape
IMPORTANT:
Adaptor
Remove the tape from damper and adaptor
before installation.As show below:
Damper
2-Screw...

Fig.3-2
Fig.4
Fan body
Joist
4-Long screws(M4X30)
Joist Fan body
2-Long screws
(M4X30)
2-Long screws
(M4X30)
Screw (M4X10)II
7
Junction box cover
Fig. 5
Conduit or wiring
Junction box
Lead wires
Green wiresWire nut
ConduitDuct
5. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig.5)
6. Refer to wiring diagram of page 4.
Using wire nuts, connect house power wires to
ventilating fan wires:
black to black; white to white; green to green;
Replace the junction...

2. Insert the suspension bracket into the adaptor and
secure it to joists by using long screws(M4X30) (Fig.8)
Keep the distance B (7/8 inch, 21.6mm) for the
thickness of ceiling board.
Fig. 6
8.
(Fig.6) Finish ceiling work. Ceiling hole should be aligned
with the edge of the flange.
9. Insert mounting springs into slots as shown and
mount grille to fan body. (Fig.7)
8
Fig. 8
1. Open the orifice cover, disconnect plug connector
from receptacle and remove adaptor from fan body
before starting...

Make sure that adaptor claws are properly inserted
into body slots.
IMPORTANT:
5. Insert the fan body into joists. (Fig.9)
6. Open the orifice cover, secure the fan body to
adaptor by using thumb screw. (Fig.10)
7. Plug connector to receptacle. (Fig.11)
When mounting
body and blower
separately
1. Loosen 3 screws (but
do not remove them
from blower). (Fig.12-1)
2. Remove blower section.
(Fig.12-2)
4. Insert fan body (without
blower section) into
joists. (Fig.9)
5. Secure the adaptor and
fan body by using...

CSuspension bracket
The suspension can comply with
different kind of -joists.III
III bracket
I
C3
C4
C1
C2
Fig. 13
2-Long screws
(M4X30)Screw (M4X10)II
10
Fig.14
Screw (M4X10)II Suspension
bracketIII
Fig.154-Long screws(M4X30)
I-joist
9. Follow step 8 to 9 of Installation (page 8) to
complete the installation work.I
3. Connect the ventilating fan to the joist. (Fig.15)I-
2. Connect the suspension to fan body. (Fig.14)
(Select the hole by checking -joist size and fix the screw
to the frame...