Panasonic Va-824 Key Telephone System Installation And Programming Manual

Extension No. 32 (OPTION)  

Extension No. 33 (OPTION) Room name: 
FEATURE 
OPTION 
SELECTED 
3 Telephone type Key telephone 
Single line telephone 
*3308-O 
X * 3308-l 
COL No. 
01 02 03 04 05 06 
07 08 
* 3301- 
Line key 1 
X 
* 3302- 
139  

Extension No. 33 (OPTION) 
6 
FEATURE 
I OPTION SELECTED 
I 
Ieceiving calls 
ram sensor 
Ione paging 
Jse of system 
#peed dial group No alarm tone 
Alarm tone ring x3307-0 
X *3307-1 
No paging Zone 1 
Zone 2 Zone 3 
*3305-o *3305-1 
X *3305-2 *3305-3 
Neither group A nor 
group B unusable O;b’a ‘p,“p A 
% Or-Wrrp B 
%Z :4;u~lleA  i 
x3301-0 x3301-1 
x3301-2 x3301-3 
X 
:lexible night 
rervice setting Can not set night mode 
Can be set night mode x3303-0 
X *3303-1 
leceiving incoming No night ring...

Priority for simultaneous calling and receiving 
The following table shows the line connection priority when simultaneous callings and receivings occur. The prior calling or 
receiving takes priority of other callings or receivings in all cases other than those marked with a symbol “*‘I in the table. 
The line connection states for later callings or receivings are as shown in the table. 
Key telephone 
141 
Later Incoming incoming 
;;;;;; ;;in;! DSS TEL intercom call 
l-7-4 incoming incoming incoming...

Single line telephone 
Incoming COL call 
= 
8 
Hold call Reminder 
P 
PE 
-s o 
3.E Incoming DSS TEL call 
Incoming intercom call 
During conversation Incoming Hold call 
COL call Reminder 
Standby 
Standby Standby 
Standby - 
* 
Standby - incoming Incoming Incoming 
DSS TEL intercom 
door box Hook-up 
call call 
call 
* 
BT ICT * 
* BT 
ICT * 
BT 
ICT * 
* 
BT 
ICT * 
BT BT 
ICT 
Incoming door box call Standby - 
I * 
I BT 
I ICT * 
I 
NOTE BT : Busy Tone. 
IT : Incoming call during Busy Tone. 
IT-2 :...

( Tones and lamp indications 
status 
:I--- 
Incoming call 
Busy 
E Hold 
.- 
0 
I----- Long hold alarm 
/ Long call alarm 
i! Busy 
.- 
I---- -j Hold 
Busy tone (BT) 
COLAntercom 
busy tone 
Sensor busy tone 
I------ 
Door box busy 
tone 
g Door box 
a, 
I-----  5 Paging 
1 ,s,e,“,sor detecting 
Timer alarm 
Microphone lamp 
DND/CF lamp 
n : TONE Interval 
Remarks 
I 
Red lamp flickers. 
Red lamp 
yie’msF’T used. lights up when other line being 
Red lamp flickers when other party is hold. 
cl 6 set cl I...

PROGRAMMING TABLE ‘- 
This table should be retained by the dealer once the installation and 
programming have been completed so that it can be used thereafter for 
maintenance purposes when necessary. 
The Installation Manual should handed over to the customer with the 
contents of the program setting recorded in it. 
Panasonic  

PROGRAMMING DESIGN TABLE (1/A- :- 
For the system and each of the key telephones, perform programming designing according to 
the following table. 
SYSTEM SETTING 
FEATURE 
Enter dial No.0 to 9 of PBX outside line access dialing digits. 
CONTENTS 
Enter dial No.0 to 9, digits of after the dialed auto pause. 
Set the time for the conversation time indication appear to after 15 set or 30 sec. 
Set the flash time to 0.6 set, 1 set or 2 sec. 
I I 
Set the auto pause time to 2 set or 3 sec. 
I I 
Enter the...

FEATURE 
Display appear timing of the delay time setting. 
Set for not outputting SMDR data, outputting with title or outputting data only. 
Set the year, mouth, day for SMDR data. 
Set the baud rate of SMDR data to 300, 600, 1200, 2400, 4800 BPS or 9600 BPS. 
Set the fram configuration (data, stop, parity) of SMDR data to 7 or 8 digits, 
1 or 2, odd or even. 
Set the type of tone or pulse for each outside line. 
Enter COL or PBX for each outside line. 
Perform MC0 (Automatic access telephone line)...

KEY TELEPHON SETTING 
15 16 
T Enter KEY TEL or SLT 
1,2,3,4,5,6,7 or 8 1  Set COL 1 
to 8, for 
the Line 
key num- 
ber. 
COLl 
COL2 
COL3 
COL4 
COL5 
COL6 Tel No. 
Tel No. 
Tel No. 
Tel No. 
Tel No. 
Tel No. 1,2,3,4,5,6,7 or 8 
CoLi’ 1 Tel No. 
COL8 1 Tel No. 
Set the incoming ringing designation 
to the ring position. Yes or No 
Yes or No 
1 COL8 
Set the door box call for one of no ring, intercom 
incoming ring only, COL incoming ring only or inter- 
com and COL incoming ring. 
Set the door box call...