Panasonic TNW2AE013 Quick Start Guide

							
Contents  
 
1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________ 26 
2. INSTALLATION _________________________________________ 28 
3. DESCRIPTION OF CONTROLS ____________________________ 30 
4. USE OF THE OVEN ______________________________________ 35 
5. AVAILABLE ACC ESSORIES _______________________________ 36 
6. COOKING HINTS ________________________________________ 37 
7. CLEANING AND MAINTENANCE ___________________________ 43 
8. EXTRAORDINARY MAINTENANCE _________________________ 45 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
INSTRUCTIONS FOR THE INSTALLER:  these are intended for the 
qualified technician who must install the appl iance, set it functioning 
and carry out an inspection test. 
 
 
INSTRUCTIONS FOR THE USER: these contain user advice, 
description of the commands and the correct procedures for cleaning 
and maintenance of the appliance. 
25  
						

							
 Introduction 
 
1. INSTRUCTIONS FOR SAFE AND PROPER USE 
 
 
THIS MANUAL IS  AN INTEGRAL PART OF THE APPLIANCE AND 
THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE 
PLACE FOR THE WHOLE WORKING LIFE OF THE OVEN. WE ADVISE 
CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS 
THEREIN BEFORE USING THE OVEN. INSTALLATION MUST BE CARRIED 
OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE 
REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC 
USES AND CONFORMS TO CURRENT  REGULATIONS IN FORCE. THE 
APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING 
FUNCTIONS:  COOKING AND HEATING-UP OF FOOD . ALL OTHER USES 
ARE CONSIDERED IMPROPER. 
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER 
USE.  
  
  
 
DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT.  SEPARATE 
THE VARIOUS WASTE MATERIALS  AND TAKE THEM TO THE NEAREST 
SPECIAL GARBAGE COLLECTION CENTRE. 
  
  
 
IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED 
ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES. 
   
 
WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT 
BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE 
COMPLYING WITH APPLICABLE REGULATIONS. 
THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN 
BUILT IN. 
NEVER UNPLUG BY PULLING ON THE CABLE.   
   
DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL 
SLITS. 
  
IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION 
TEST OF THE OVEN, FOLLOWING TH E INSTRUCTIONS BELOW. SHOULD 
THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND 
CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. 
NEVER ATTEMPT TO REPAIR THE APPLIANCE.  
26   
						

							
Introduction   
 
  
 ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE “ZERO” (OFF) 
POSITION WHEN YOU FINISH USING THE OVEN. 
 
  
NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE 
ACCIDENTALLY LIGHTED AND CAUSE FIRES. 
  
DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO 
TOUCH THE HEATING ELEMENTS INSIDE THE OVEN. 
  
THE I.D. PLATE WITH TECHNICAL DATA, REGISTRATION NUMBER AND 
BRAND NAME IS POSITIONED VISIBLY ON THE OVEN DOOR FRAME. 
THE PLATE MUST NOT BE REMOVED.  
  
THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING 
CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN 
EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY 
ARE SUPERVISED OR INSTRUCTED BY ADULTS OR PEOPLE 
RESPONSIBLE FOR THEIR SAFETY. 
 
 
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 
2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT 
(WEEE). 
THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF 
RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC 
EQUIPMENT. 
 
  
BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND 
PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED. 
  
 
 The manufacturer declin es all responsibility for damage to persons 
or things caused by non-observance  of the above prescriptions or by 
interference with any part of the appliance or by the use of non-original 
spares.  
27  
						

							
 
 
Instructions for the installer 
 
28 
2. INSTALLATION 
 
2.1  Electrical connection 
 
Check that mains voltage and power cable ratings are as per the 
indications provided on the label attached to the oven door frame.   
This label must never be removed.  
 
 
It is obligatory for the electrical system to be grounded according to the 
methods required by safety rules. 
 
 
If a plug and socket connection is being used make sure that the plug 
and socket are compatible. Avoid use of adapters and shunts as these 
could cause overheating and risk of burns. 
 
 
If a fixed connection is being used fit power line with an omnipolar circuit 
breaker with a contact opening gap equal to or greater than  3 mm in an 
easily accessible position in proximity to the oven. 
 
  
  
 For operation on 230-240V∼: use an 
H05RR-F / H05V2V2-F type three-core 
cable (3 x 1.5 mm2).  
 
 
 
The cable end to be connected to the 
appliance must be provided with an ground 
wire (yellow-green) at least 20 mm longer.  
 
  
 
 The manufacturer declin es all responsibility for damage to persons 
or things caused by non-observance  of the above prescriptions or by 
interference with any part of the appliance.  
  
						

							
 
Instructions for the installer  
  
Mounting the oven 
The oven is designed for mounting into any piece of furniture as long as 
heat-resistant. Proceed according to the dimensions shown in Figures 1, 
2 .
  
  
Fixing is carried out using 4 screws at 
the corners C of the oven door 
frame, after removing the side panels 
secured by the screws A and the 
supports B as shown in figure 3.  To 
replace the side panels, take care to 
engage the pins inside them correctly 
with the supports B, then retighten 
the screws A. 
 3.  
  
  
 Never use the oven door to lever the oven into 
place when fitting. 
Avoid exerting too much pressure on the oven door 
when open. 
 
29  
						

							
 
 
Instructions for the user 
 
30 
3. DESCRIPTION OF CONTROLS  
3.1  Front control panel 
All the oven controls are grou ped together on the front panel.  
         
FUNCTION SWITCH KNOB  
Rotate the knob in either direction  to select desired function from the 
following: 
 
  
NO FUNCTION SET LOWER HEATING ELEMENT 
+  VENTILATED HEATING 
ELEMENT 
 
 
UPPER AND LOWER  HEATING ELEMENT VENTILATED HEATING 
ELEMENT + VENTILATION 
 
 
WIDE GRILL ELEMENT UPPER AND LOWER 
HEATING ELEMENT + 
VENTILATION 
 
  
GRILL  ELEMENT  
 
LOWER HEATING ELEMENT 
+ VENTILATION 
  WIDE GRILL ELEMENT + 
  VENTILATION   
 
  
OVEN LIGHT WIDE GRILL ELEMENT + 
VENTILATION 
  
UPPER AND LOWER  HEATING ELEMENT UPPER AND LOWER 
HEATING ELEMENT + 
VENTILATION 
 GRILL ELEMENT     DEFROSTING 
 
 
 
 
  
						

							
 
Instructions for the user  
  
 
THERMOSTAT KNOB  
Cooking temperature is selected by 
turning the knob clockwise to the 
desired setting, between 50° and 
250°C.       
 
THERMOSTAT INDICATOR LIGHT 
When this light comes on, the oven is heating up.  
When this light goes out, the preset heating 
temperature has been reached.  
When the light flashes, the temperature inside the 
oven is steady at the set temperature.  
  
 
 
31  
						

							
 
 
Instructions for the user 
 
32 
3.2  Electronic Programmer 
   The programmer user instructi ons are valid only for the main oven.  
  
 
  
 
 
  LIST OF FUNCTIONS     MINUTE-COUNTER KEY     COOKING TIME KEY     END-OF-COOKING KEY     DECREASE TIME KEY     INCREASE TIME KEY    
 
 
3.2.1 Clock adjustment 
When using the oven for the first time, or after a power failure, the display 
flashes regularly and indicates 
. Press the keys    and at the 
same time the keys 
 or : each single press changes the time by 1 
minute either up or down. 
   Before setting the programmer activate the desired function and 
temperature.  
  
						

							
 
Instructions for the user  
  
3.2.2 Semiautomatic cooking 
Use this setting for automatic oven switch-off at the end of cooking time.  
By pressing key , the display lights up, showing ; keep the key 
pressed and at the same time, press keys 
 or  to set the cooking 
time.  
Release key  to start the programmed cooking time count. The display 
will now show the right time together with symbols  A and 
. 
 
3.2.3  Automatic cooking 
Use this setting to automatically start and stop the oven. 
By pressing key , the display lights up showing ; keep the key 
pressed and at the same time, press keys 
 or  to set the cooking 
time. 
By pressing key  the sum of the right time + cooking time will appear; 
keep the key pressed and at the same time, press keys 
 or   to 
regulate the end of cooking time.  
Release key  to start the programmed count and the display will show 
the right time together with symbols  A and 
. 
   
After set-up, to see the cooking time remaining, press the key ; to see 
the end of cooking time press the key . 
Set-up with incoherent values is logi cally prevented (e.g. the contrast  between a cooking time and a longer period will not be accepted by the 
programmer).   
3.2.4 End of cooking 
When cooking is over, the oven will automatically switch off and, at the 
same time, an intermittent alarm will so und. After switching off the alarm, 
the display will once again show t he right time together with the symbol 
, indicating that the oven has returned to manual operation mode. 
 
 
3.2.5 Adjusting alarm volume 
The acoustic alarm has three different  settings. These can be operated, 
while the alarm is sounding, by pressing key 
. 
 
3.2.6  Switching off the alarm 
The alarm switches off automatically  after seven minutes. They can be 
manually de-activated by pressing the keys 
 and  together.  
33