Panasonic Th 60pf30 Operating Instructions

SET UP for Input Signals
• SYNC
This function operates only during input from PC IN terminal.
Setting RGB sync signal
Con rm that the input is set to RGB input (this setting is valid only for RGB input signal).
AUTO: 
The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
ON G:  Uses a synchronized signal on the Video G signal, which is input from the G connector.
VBS:  Uses a synchronized signal of Composite Sync input, which is input from the...

ADVANCED NR[ 
VIDEO ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
Digital ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
COMPONENT ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
RGB ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
()NOISE REDUCTION
OFF 
()NOISE REDUCTION
ADVANCED
H-FREQ.
V- F R E Q .kHz
Hz 63.98
60.02
SIGNAL FORMAT 1280×1024/60i
H-FREQ.
V- F R E Q .kHz
Hz 63.98
60.02
DOT CLOCK FREQ.MHz 108.0
SIGNAL FORMAT 1280×1024/60i
52
VIDEO NR:        Automatically reduces...

MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
NETWORK SETUP
DISPLAY ORIENTATION
LANDSCAPE PORTRAIT SETUP
2/2 SETUP
--:--:--:--:--:--
DHCP
NETWORK SETUP
SAVE
0
192.168.    0.    8
255.255.255.    0
192.168.    0.    1
1024
AUTO
RS-232COFF
SUBNET MASK
LAN SPEED GATEWAY IP ADDRESS
PORT
CONTROL I/F SELECT NETWORK ID
MAC ADDRESS
Network Setup
Make the various settings to use the network function.
  
DHCP, IP ADDRESS, SUBNET MASK, and GATEWAY settings
1 Set DHCP.
     When “OFF” is selected, IP ADDRESS...

Options 
Weekly Command TimerAudio input select
1/3 
 
Touch Panel settings
Initial input Onscreen displayOn
Off
Off Off
0 0Maximum VOL level Initial VOL levelOffInput lockOffButton lockOffRemocon User level
Options 
Enable Off-timer function Normal Initial Power Mode 0 ID select Off Remote ID Off Serial ID Off Display size Off Studio W/B Off Studio Gain 
2/3 
 
3/3 Options 
O f f 
Off
Off Clock Display
Rotate
Off All AspectManual Auto Setup Slot power 
Off
Power On Screen Delay
3D Safety Precautions...

55
Item Adjustments
Input lockLocks the input switch operation.
Off 
 PC  SLOT INPUT*1  VIDEO  COMPONENT*2  HDMI  DVI
*1 “SLOT INPUT” is displayed when an optional Terminal Board is installed.
 When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.*2  “COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”. (see page 49)Notes:
• Only the adjusted signal is displayed (see page 18).
• Input switch can be used when...

56
Item Adjustments
Studio W/BOff:  Nullify all the settings adjusted.
On:  Sets the color temperature for TV studio.
Note:  Valid only when the “WARM” is set as “COLOR TEMP” in PICTURE menu.
Studio GainSharpens the contrast for a better view when a part of the image is too light to see.
Off:  Disables “Studio Gain”.
On:  Enables “Studio Gain”.
Note:  This setting is valid only when the input signals are as follows:
    Component Video, RGB (analog), SDI, HDMI
Slot powerOff 
 Auto  On 
Off:  Power is not...

57
Options Adjustments
Weekly Command Timer
You can set 7-day timer programming by setting time and command.
Note: 
Before setting Weekly Command Timer, set PRESENT TIME SETUP.  (see page 35)
Press to select Function.
Press to select “On”.
Note:
•  When Function is set to On, SET UP TIMER 
(see page 35) is unavailable and INTERVAL / 
TIME OF DAY in MODE of SCREENSAVER 
(see page 37) cannot be selected.
1
Press to select a day.
Press to select a program number.
Note:
•  You can set the program from 1 to...

Weekly Command Timer 
0210:30 Command No Time IMS:SL1 Command 
1Program
Weekly Command Timer 
Command 
02Command No 
IMS:SL1 10:30 Time 
1Program
58
Options Adjustments
Press to select Command No.
Press to select a command number.6
Press to select Time / Command.
Press to set each item.
Time:  Set the time to execute a command program.
      Pressing “
” or “” button once changes “Time” 1 
minute.
     Pressing “
” or “” button continuously changes “Time” by 15 minutes.
Command:  Select a command to...

59
Set up the sound when an image input is selected.
Image input  Audio input
[SLOT INPUT]*1  SLOT INPUT / VIDEO / COMPONENT / DVI/PC / NO AUDIO
[VIDEO]  SLOT INPUT / VIDEO / COMPONENT / DVI/PC / NO AUDIO
[COMPONENT]*2  SLOT INPUT / VIDEO / COMPONENT / DVI/PC / NO AUDIO
[HDMI]  SLOT INPUT / VIDEO / COMPONENT / HDMI / DVI/PC / NO AUDIO
[DVI]  SLOT INPUT / VIDEO / COMPONENT / DVI/PC / NO AUDIO
[PC]  SLOT INPUT / VIDEO / COMPONENT / DVI/PC / NO AUDIO
  DVI/PC: Sound input for both DVI and PC.
  NO AUDIO: No...

60
Press ACTION  (  ) button
Options 
Audio input selectTouch Panel settings
1/3 
 
Weekly Command Timer
Touch Panel mode
Calibration mode
Touch Panel settings
On
Touch Panel mode
Calibration mode
Touch Panel settings
On
The screen is displayed in the middle and NANODRIFT is deactivated for 180 seconds. 
After 180 seconds or when you have the menu displayed with a remote control, Calibration 
mode is cancelled.
Note: 
For information on how to set up Calibration, please see Touch Panel instruction...