Panasonic Th 60pf30 Operating Instructions

INPUT MENU  ENTER/ +/  VOL -/ 
21
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format 
picture.
Press repeatedly to move through the aspect options:
For details about the aspect mode, please see “List of Aspect Modes” (page 67). 
The aspect mode changes each time the ENTER button is pressed. [from the unit]
Note: 
Be aware that if you put the display in a public place for commercial purposes or a public showing and 
then...

INPUT MENU  ENTER/ +/  VOL -/ 
2 
EXIT
2 
1 
EXIT
s1 
 s2 
 s3 
 s4 
22
VOL button
Digital Zoom
This displays an enlargement of the designated part of the displayed image.
Select the area of the image to be enlarged.
Press on the enlargement location to select.
Return to normal display (quit Digital Zoom).
Press to exit from the Digital Zoom.
Notes:
•  When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
•  The Digital Zoom function cannot be selected while in the following...

23
Viewing 3D images
You can enjoy viewing 3D images with contents or programmes compatible with 3D effect by using the 3D eyewear 
(optional).
Note:
You need the 3D IR TRANSMITTER (optional) and the 3D eyewear (optional) to view the 3D images on this display.
For further information, see the instruction manuals of the 3D IR TRANSMITTER and the 3D eyewear.
This display supports “Frame Sequential
*1”, “SIDE BY SIDE*2”, “TOP AND BOTTOM*3” and “SIMULTANEOUS*4” 3D 
formats.
*
1:  The 3D format that the...

24
Troubleshooting for 3D Eyewear 
Table of images that can be seen for each 3D Picture 
Format and the source image format
Symptoms Checks
Cannot see 3D images •  Has the 3D Eyewear been switched On?
•  Ensure that “3D EYEWEAR” in “3D SETTINGS” is set to “ON”. (see 
page 36)
•  Some 3D image signals may not be automatically recognized as 3D 
images. Set “3D INPUT FORMAT” in “3D SETTINGS” to match the 
picture format. (see page 36)
•  Check that there are no obstacles between the 3D IR TRANSMITTER 
and...

1/2
3D SETTINGS
SIGNAL
EXTENDED LIFE SETTINGS
INPUT LABEL
SET UP
OFF
STANDBY SAVE
ON
PC POWER MANAGEMENTONDVI-D POWER MANAGEMENTOFFNO SIGNAL POWER OFFENABLENO ACTIVITY POWER OFFDISABLE
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
POWER SAVE
2/2 SET UP
MULTI DISPLAY SETUP
SET UP TIMER
NETWORK SETUP
PRESENT TIME SETUP
DISPLAY ORIENTATIONLANDSCAPE
PORTRAIT SETUP
25
On-Screen Menu Displays
Remote Control Unit
1Display the menu screen.
Press to select.
(Example: PICTURE menu)
MENU
 Press...

00
NORMAL NORMALIZE 
AUTO SETUP
POS./SIZE
V-POS 
0 
H-POS 
V-SIZE DOT CLOCKH-SIZE 
CLAMP POSITION CLOCK PHASE
1:1 PIXEL MODEOFF
0 0 0 
0 
26
Adjusting POS./SIZE
1Press to display the POS./SIZE menu.
Press to select the menu to adjust.
Press to adjust the menu.
Press to exit from adjust mode.
Notes:
•  Adjustment details are memorized separately for different input signal formats. (Adjustments for component signals are 
memorized for 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i ·...

27
H-POSAdjust the horizontal position.V-POSAdjust the vertical position.
H-SIZEAdjust the horizontal size.V-SIZEAdjust the vertical size.
DOT 
CLOCK(During Component/PC input signal)
Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, 
adjust so that any such noise is minimized.
CLOCK 
PHASE(During Component/PC input signal)
Eliminate the 	 ickering and distortion.
OVER 
SCANTurn image over scan ON/OFF.
Con gurable signals are as follows:
525i,...

28
While the POS./SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION 
(
  ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
Helpful Hint (  
 / NORMALIZE  
 Normalization)
Adjusting POS./SIZE
1:1 PIXEL MODEAdjusts the display size when 1125i, 1125p or 1250i signal is input.
Notes:
•  Select ON when you would like to replay 1920 × 1080 input signal.
•  Applicable input signal;
  1125 (1080) / 50i...

BLACK EXTENSION 
GAMMA  INPUT LEVEL 
ADVANCED SETTINGS 
NORMAL NORMALIZE 
W/B LOW B W/B HIGH R
W/B LOW R
W/B LOW G W/B HIGH G
W/B HIGH B0
0
2.2
0
0 0
0
0
0
25
0
0
0
5
PICTURE
NORMALNORMALIZESTANDARD
BRIGHTNESS
SHARPNESS PICTURE MENU
COLOR PICTURE
TINT
ADVANCED SETTINGSCOLOR TEMPNORMAL
29
PICTURE Adjustments
1
ADVANCED SETTINGS
Enables  ne picture adjustment at a professional 
level (see next page).Press to enter Advanced 
Settings.
While the “PICTURE” menu is displayed, if either the N button on the...

30
PICTURE Adjustments
ADVANCED SETTINGS
Notes:
• 
You can change the level of each function 
(PICTURE, BRIGHTNESS, COLOR, TINT, 
SHARPNESS) for each PICTURE MENU.
• The setting details for STANDARD, DYNAMIC,
CINEMA and MONITOR respectively are 
memorized separately for each input terminal.
• In PICTURE, there is not a noticeable change 
even when contrast is increased with a bright 
picture or reduced with a dark picture.
On the remote control unit, while the “ADVANCED SETTINGS” menu is displayed, if...