Panasonic Th 50pf30 Operating Instructions

61
Using Network Function
This unit has a network function to control the network connected display with your computer.
Note:
To use the network function, set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” 
to “LAN”. (see page 53)
When “LAN” is set, the slot power is turned on, and power indicator is lit orange under the condition of power off with 
remote control (stand-by state), regardless of the “Slot power” setting. (see page 56)
Example of Network Connection
Command...

62
Using Network Function
PJLink™ Protocol
The network function of the unit conforms with PJLink™ class 1 and you can operate the following actions from your 
computer using PJLink™ protocol. 
• Display setup
•  Display status query
Supported commands
Commands to control the unit with PJLink™ protocol are shown in the table below.
PJLink™ security authentication
Set “Panasonic” for the PJLink™ password.
•  PJLink™ is a pending trademark in Japan, the United States, and other countries or areas. 
Command...

63
Unit Setup
Set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” to “LAN”. (see page 53)
Computer Setup
Disable the proxy server settings and enable JavaScript. 
You can use a Web browser to control the unit and set up a network and password.
Access to the TOP screen of the Web browser control using a Web browser. To use the Web browser control, the unit and computer setups are required.
(Windows) (Macintosh)
Disable proxy server settings
1  Display [Internet Properties]...

64
Using Web Browser Control
TOP screen structure of the Web browser control
After logging in, the TOP screen of the Web browser control is displayed.
  Menu
Menu items are displayed. When a button is clicked, 
setup screen of each item is displayed.
Item Details
BASIC 
CONTROLBASIC CONTROL screen is displayed. 
(see below)
OPTION 
CONTROLOPTION CONTROL screen is 
displayed. (see below)
NETWORK 
SETTINGNetwork Setup screen is displayed.
(see page 65)
CHANGE 
PASSWORDPassword setup screen is displayed....

65
Notes:
•  To use a DHCP server, make sure the DHCP server 
is started.
•  During a DHCP server is used, IP ADDRESS, 
SUBNET MASK, and GATEWAY values cannot be 
entered.
•  When the set values are changed properly, 
“NETWORK SETTING CHANGED.” message and 
the changed set items are displayed.
Item Details
DHCPSet to ON when a DHCP server is 
used, or OFF when it is not used.
IP ADDRESS Enter an IP address.
SUBNET MASK Enter a subnet mask.
GATEWAY Enter a gateway address.
PORTEnter the port number used...

66
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Checks
Picture Sound
InterferenceNoisy SoundElectrical Appliances
Cars / Motorcycles
Fluorescent light
Normal PictureNo SoundVolume
(Check whether the mute function has been activated on the remote control.)
No PictureNo SoundNot plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote...

67
List of Aspect Modes
Aspect mode
Picture 
 Enlarged screenDescriptionAll Aspect: 
OnFactory setting
All Aspect: Off
16:9 FULL
The display of the pictures  lls the screen.
In the case of SD signals, pictures with a 4:3 aspect ratio are 
enlarged horizontally, and displayed. This mode is suited to 
displaying anamorphic pictures with a 16:9 aspect ratio.
14:9 –
Letterbox pictures with a 14:9 aspect ratio are enlarged 
vertically and horizontally so that their display  lls the 
screen vertically and is...

68
Applicable Input Signals
*Mark: Applicable input signal
Signal nameHorizontal frequency 
(kHz) Vertical frequency 
(Hz) COMPONENT / RGB IN 
/ PC IN
(Dot clock (MHz))DVI-D IN
(Dot clock 
(MHz))HDMI
1   525  (480) / 60i  15.73 59.94 *  (13.5) *  (27.0) *
2   525  (480) / 60p  31.47 59.94 *  (27.0)   
5 * (27.0) *
3   625  (575) / 50i  15.63 50.00 *  (13.5)
4   625  (576) / 50i 15.63 50.00 *  (27.0) *
5   625  (575) / 50p  31.25 50.00 *  (27.0)
6   625  (576) / 50p  31.25 50.00 *  (27.0) *
7   750...

69
Applicable Input Signals
1/2
SIGNAL
EXTENDED LIFE SETTINGS
INPUT LABEL
SET UP
OFF
STANDBY SAVE
OFF
PC POWER MANAGEMENTONDVI-D POWER MANAGEMENTOFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
POWER SAVENO SIGNAL POWER OFFENABLENO ACTIVITY POWER OFFDISABLE
3D SETTINGS
This function allows you to reset the unit to the factory setting.
Shipping condition
1
4
5Press to display the SET UP menu.
Press to select “OSD LANGUAGE”.
Press for more than 3 seconds.
Press to select “Shipping”....

70
Command list of Weekly Command Timer
No. Command Control details
1 AAC:MENCLR Audio Menu (CLEAR)
2 AAC:MENDYN Audio Menu (DYNAMIC)
3 AAC:MENSTD Audio Menu (STANDARD)
4 AAC:SURMON Surround (ON)
5 AAC:SUROFF Surround (OFF)
6 AMT:0 Audio Mute (OFF)
7 AMT:1 Audio Mute (ON)
8 
9 
10 AVL:00 Audio Volume (00)
11 AVL:10 Audio Volume (10)
12 AVL:20 Audio Volume (20)
13 AVL:30 Audio Volume (30)
14 AVL:40 Audio Volume (40)
15 AVL:50 Audio Volume (50)
16 AVL:60 Audio Volume (60)
17 DAM:FULL Aspect (FULL)
18...