Panasonic Th 42pr10r Operating Instructions

							31
1/2
PC
Off
Standby saveOff
Power management
Off
Auto power off
Off
OSD Language
English (
UK) Component/RGB-in select
RGB
Input labelSignal
Power save
Setup
1/2
PC
Off
Standby saveOn
Power management
Off
Auto power off
Off
OSD Language
English (
UK) Component/RGB-in select
RGB
Input labelSignal
Power save
Setup
Reduces power consumption
Press to select 
“Power save”
“Standby save”
“Power management”
“Auto power off”.
Press to select “On” or “Off”.
On  Off
Press to exit from Setup. • Power save:  When this function is turned On, luminous level of the Plasma Display is suppressed, so 
power consumption is reduced.
• Standby save:   When this function is turned On, power consumption of the microcomputer is reduced 
during power supply standby (see page 11, 12-13), so standby power of the set is reduced.
• Power management:  The unit power supply is turned On or Off depending on whether or not there is a signal 
during PC input mode. 
 
This function is enabled when it is turned On. (Only during input from PC (Mini D-sub) terminal)
• Auto power off:  Equipment power supply is turned Off when there is no signal.
  When this is set to On, the power supply of the unit goes Off 10 minutes after the input 
signals stop. 
  This function is effective for input signals except input from PC (Mini D-sub) terminal.
Press to select Input label.
Press to change the Input label.
Customizing the Input labels
This function can change the label of the Input signal to be displayed.
Select the input signal which you would like to change its label before customizing the Input labels. (see page 13, 16)
Note:
While selecting an Input signal through Optional Terminal Board connected to Slot1, Slot2 and Slot3, the Input label 
will depend on each Optional Terminal Board.
Input labels for Slot1, Slot2, Slot3 and Mini D-sub:
[Slot1 Input]  
INPUT1 / VIDEO1 / COMPONENT1 / RGB1 / DIGITAL1 / PC1 / DVD1 / CATV1 / VCR1 / STB1
[Slot2 Input]  INPUT2 / VIDEO2 / COMPONENT2 / RGB2 / DIGITAL2 / PC2 / DVD2 / CATV2 / VCR2 / STB2
[Slot3 Input]  INPUT3 / VIDEO3 / COMPONENT3 / RGB3 / PC3 / DVD3 / CATV3 / VCR3 / STB3
[PC (Mini D-sub) input]  PC / COMPONENT / RGB / DVD / STBNote:
“Power management” and “Auto power off” are effective 
during normal viewing (one picture screen) only.
1
2
3
Addition sign“A” “B”
Selected InputComposite S VIDEO When BNC Dual Video Terminal Board (TY-FB9BD) is used, an “A” or “B” is added at the end of each input label, 
depending on the input selected (see below).
 Ofrecido por www.electromanuales.com
 
						

							32
1/2 
PC 
Off 
Standby save 
Off 
Power management 
Off 
Auto power off 
Off 
OSD Language 
English (
UK)  Component/RGB-in select 
RGB 
Input label Signal 
Power save 
Setup 
1/2
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD LanguageEnglish (
UK) Component/RGB-in select
RGB
Input labelSignal
Power save
Setup
3D Y/C Filter (NTSC)
Colour system
Signal
On
Auto
Cinema reality
Panasonic Auto (4 : 3)Off
4 : 3
P-NROff
[ 
AV  ]
Setup for Input Signals
Component / RGB-in select
Select to match the signals from the source connected to the Component / RGB input terminals.
Y,  P
B, PR signals  
“Component”
R, G, B, HD, VD signals  
“RGB”
1
2Press to display the Setup menu.
Press to select the “Component / RGB-in 
select”.
Press to select the desired input signal.
Component  RGB
Press to exit from adjust mode.
3D Y/C Filter – For NTSC AV images
Select “Signal” from the “Setup” menu during AV(S Video) input signal. (“Signal 
[AV]” menu is displayed.)
Press to select the “3D Y/C Filter (NTSC)”
Press to set On / Off.
Press to exit from adjust mode.
Note:
When On, this setting only affects NTSC input signals. Note:
Selection may not be possible, depending on which optional board is installed.
3
1
2
Press ACTION  (  ) button
 Ofrecido por www.electromanuales.com
 
						

							33
1/2
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD LanguageEnglish (
UK) Component/RGB-in select
RGB
Input labelSignal
Power save
Setup
3D Y/C Filter (NTSC)
Colour system
Signal
On
Auto
Cinema reality
Panasonic Auto (4 : 3)Off
4 : 3
[ 
AV  ]
P-NROff
1/2
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD LanguageEnglish (
UK) Component/RGB-in select
RGB
Input labelSignal
Power save
Setup
1
23D Y/C Filter (NTSC)
Colour system
Signal
On
Auto
Cinema reality
Panasonic Auto (4 : 3)Off
4 : 3
[ 
AV  ]
P-NROff
Cinema reality
P-NR
Signal
Off
Off
[ 
Component ]
Cinema reality
P-NR
Signal
Off
Off
H-Freq.
V-Freq.kHz
Hz33.8
60.0
[ 
Digital ]
Sync
P-NR
Signal
Auto
H-Freq.
V-Freq.kHz
Hz33.8
60.0
[ 
RGB ]
Cinema realityOff
Off
Setup for Input Signals
Colour system / Panasonic Auto
Select Signal from the “Setup” menu during AV(S Video) input signal. (“Signal 
[AV]” menu is displayed.)
Press to select the “Colour system” or 
“Panasonic Auto”.
Press to select each functions.
If the picture image becomes unstable:
With the system set on Auto, under conditions of low level or noisy input 
signals the image may in rare cases become unstable. Should this occur, 
set the system to match the format of the input signal.
Cinema reality / P-NR
Press to select Cinema 
reality or P-NR.
Press to set On / Off.
Press to exit from adjust mode. Cinema reality:
When on, the display attempts to reproduce a more natural interpretation of sources 
such as movie pictures, which are recorded at 24 frames per second.
If the picture is not stable, turn the setting to off.
Note:
When On, this setting only affects the following signal input:
•  NTSC / PAL signal input during “AV(S Video)” input signal.
• 
525i(480i), 625i(575i), 1125(1080) / 60i signal input during “Component” input signal.
P-NR:
Automatically reduces unwanted picture noise.
Note: 
P-NR cannot be adjusted while a PC signal is being applied.Press ACTION  (  ) button
Press ACTION  (  ) button Mode Function
Colour systemSet the colour system to match the input signal. When selecting “Auto”, the color system is 
automatically selected from NTSC/PAL/SECAM, however, M.NTSC signal is not displayed 
properly depending on the attached terminal board. To display M.NTSC signal, select 
“M.NTSC” in Colour system.
Auto SECAM M.NTSC NTSCPA L
Panasonic Auto 
(4 : 3)Set to “4 : 3” to view 4:3 images in an unchanged format when Panasonic Auto is selected. 
If you would like to view 4:3 images in Just format, set to “Just”.
Note: 
Panasonic Auto does not function when BNC Dual Video Terminal Board (TY-FB9BD) is used.
 Ofrecido por www.electromanuales.com
 
						

							34
Sync
Auto
Sync
on G
Sync
VBS
1/2
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD LanguageEnglish (
UK) Component/RGB-in select
RGB
Input labelSignal
Power save
Setup
Sync
P-NR
Signal
Auto
H-Freq.
V-Freq.kHz
Hz33.8
60.0
[ 
RGB ]
Cinema realityOff
Off
H-Freq.
V-Freq.kHz
Hz33.8
60.0
3D Y/C Filter (NTSC) 
Colour system 
Signal 
Auto Cinema reality 
Panasonic Auto (4 : 3) Off 
4 : 3 
[ 
AV  ] 
P-NR Off Refresh Rate100 Hz
Cinema reality 
P-NR 
Signal 
Off 
Off 
[ 
Component ] 
Refresh Rate100 Hz
Cinema reality 
P-NR 
Signal 
Off 
Off 
H-Freq.
V-Freq.kHz
Hz33.8
60.0
[ 
Digital ] 
Refresh Rate100 Hz
Sync 
P-NR 
Signal 
Auto 
H-Freq.
V-Freq.kHz
Hz33.8
60.0
[ 
RGB ] 
Cinema reality Off 
Off 
Refresh Rate100 Hz
Select Signal from the “Setup” menu during RGB input signal.
Press to adjust.
Setting RGB sync signal:
Confi rm that the input is set to RGB input (this setting is valid only for RGB input 
signal).
Auto:  The H and V sync or synchronized signal are automatically selected. 
If both input, it is selected the H and V sync.
on G:  Uses a synchronized signal on the Video G signal, which is input 
from the G connector.
VBS:  Uses a synchronized signal of Composite Sync input, which is input 
from the HD connector.
Displays the H (Horizontal) / V (Vertical) frequencies.
This display is valid only for RGB / PC and Digital input signal. 
Display range:
Horizontal 15 - 110 kHz
Vertical  48 - 120 Hz
H-Freq. (kHz) / V-Freq. (Hz) Sync
1
2
Press ACTION  (  ) button
Press to exit from adjust mode.
Refresh Rate (for TH-37PR10R, TH-42PR10R)
Press to select Refresh Rate.
Press to adjust. This function sets the refresh rate of the display.
This menu is displayed when the input signal is 50 Hz system (50i, 50p, 25p, 24p, 24sF) of vertical scan rate.
100 Hz: Reduce screen fl icker.
50 Hz: Enhance the resolution of moving images.
Note: 
It is recommended to set to 100 Hz normally.1
2
Press to exit from adjust 
mode.
Setup for Input Signals
 Ofrecido por www.electromanuales.com
 
						

							35
1/3Options
Off-timer function
INPUT lock
Studio W/B
Advanced PIP
Display size Initial VOL level
Maximum VOL level Initial INPUT Onscreen display
Off
Off
Off
Off Enable
On
Off
0
Off Off
0
Options Adjustments
1
2
3
5Press to display the Setup menu.
Press to select “OSD Language”.
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
Press to adjust the menu.
Press to exit from 
Options menu.
4
6
Item Effect Adjustments
Off-timer 
function
EnableDisable
Enable:  Enables the “Off-timer function”.
Disable:  Disables the “Off-timer function”.
Note:    When “Disable” is set, the Off-timer is cancelled.
Onscreen 
display
On Off
On:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial INPUTOff  PC  INPUT1  INPUT2  INPUT3 
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 16).
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
• When a dual input terminal board is attached, A or B is displayed depending on the selected 
input signal. (Ex. INPUT1A, INPUT1B)
(For TH-42PG10R)
 Ofrecido por www.electromanuales.com
 
						

							36
1/3Options
Off-timer function
INPUT lock
Studio W/B
Advanced PIP
Display size Initial VOL level
Maximum VOL level Initial INPUT Onscreen display
Off
Off
Off
Off Enable
On
Off
0
Off Off
0
Options Adjustments
Item Effect Adjustments
Initial VOL 
level
Off On
Press  button to adjust the volume when the unit is turned on.
Off  On
Off:  Sets normal volume.
On:  Sets your preferred volume.
Notes:
• 
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.• You can hear the changed volume regardless of your volume setting before opening the options menu if 
you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL 
level
Off On
Press  button to adjust the maximum volume.
Off  On
Off:  Sets auto maximum volume.
On:  Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” 
automatically becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• 
You can hear the changed volume regardless of your volume setting before opening the options menu if 
you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
INPUT lockOff   PC   INPUT1   INPUT2   INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 16).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
•  In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value 
input in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected 
input signal. (Ex. INPUT1A, INPUT1B)
Studio W/B
Off On
Off:  Nullify all the settings adjusted.
On:  Sets the colour temperature for TV studio.
Note:  Valid only when the low is set as colour temperature on screen adjustment.
Advanced PIP
Off On
Off:  Sets normal two screen display mode (see page 19).
On:  Sets Advanced PIP mode (see page 20).
Notes:
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
• 
,  buttons are unavailable during Advanced PIP mode operation.
Display size
Off On
Adjusts the image display size on screen.
Off:  Sets the normal image display size on screen.
On:  Sets the image display size approximately 95 % of the normal image display.
       Off       On
   
Notes:
• This setting is valid only when the input signals are as follows; 525i, 525p, 625i, 625p, 750/60p, 
750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 1250/50i (Component 
Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi screen is selected.
• When Display size is set to “On”, Pos. /Size adjustment cannot be used. 
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
 Ofrecido por www.electromanuales.com
 
						

							37
2/3Options
OffOffOff
Off
0
Remote ID
Serial ID ID select Button lock
Remocon User level
3/3Options
Off
Off
Off V. lnstallation
Rotate
Slot1
Serial Slot Select Slot power
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote 
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the 
VOLbutton on main unit together with  button on the remote control and hold for more than 5 seconds. 
The “SHIPPING” menu is displayed and the lock is released when it disappears.Item Effect Adjustments
Button lockOff  MENU&ENTER  On 
Off:  All the buttons at the bottom of the main unit can be used.
MENU & ENTER:
  Locks 
MENU and ENTER/ buttons on bottom face of main unit.
On:  Locks all the button on bottom face of main unit.
Remocon 
User levelOff   User1   User2   User3 
Off:  You can use all of the buttons on the remote control.
User1:
  You can only use , , , , , , ,  buttons on the remote 
control.
User2:
 You can only use , , buttons on the remote control.
User3: Locks all the buttons on remote control.
ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
Remote ID
Off On
Off:  Disables ID remote control functions. You can use normal remote control operations.
On:  Enable ID remote control functions.
Serial ID
Off On
Sets the panel ID Control.
Off:  Disables external control by the ID.
On:  Enables the external control by the ID.
Item Effect Adjustments
Slot PowerOff  Auto  On 
Off:  Power is not transmitted to the slot power.
Auto:  Power is transmitted to the slot power only when main power is on.
On:  Power is transmitted to the slot power when main power is on or in the standby state.
Note:  In some cases, power is transmitted to the slot power when main power is on or in the 
standby state regardless of the slot power setting.
V.Installation
Off OnThis mode is unavailable.
Rotate
Off On
Off:  Does not rotate the image.
On:  Rotates the image 180 degrees.
Serial Slot 
SelectSlot1  Slot2   Slot3
Selects the slot which communicates serial.
Note: 
The setting of an external command can be set only from the fi xed serial terminal (see page 10).
Options Adjustments
 Ofrecido por www.electromanuales.com
 
						

							38
Options 
Weekly Command Timer 
Initial VOL level 
1/3 
 
Off  Off 
0  0 Maximum VOL level Off INPUT lock Off Button lock Off Remocon User level Off Advanced PIP 
Initial INPUT  Onscreen display On 
O f f 
Item Effect Adjustments
Weekly 
Command 
TimerSets Weekly Command Timer. (see page 42)
Onscreen 
display
On Off
On:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial INPUTOff  PC  INPUT1  INPUT2  INPUT3 
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 16).
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
• When a dual input terminal board is attached, A or B is displayed depending on the selected 
input signal. (Ex. INPUT1A, INPUT1B)
1
2
3
5Press to display the Setup menu.
Press to select “OSD Language”.
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
Press to adjust the menu.
Press to exit from Options menu.
4
6
Options Adjustments
(For TH-37PR10R, TH-42PR10R)
 Ofrecido por www.electromanuales.com
 
						

							39
Options 
On Weekly Command Timer Onscreen display Off Initial INPUT 
1/3 
 
Maximum VOL level  Initial VOL level 
Button lock 
INPUT lock 
Advanced PIP 
Remocon User level 
Off  Off 
0  0 
Off 
Off 
Off 
Off 
Item Effect Adjustments
Initial VOL 
level
Off On
Press  button to adjust the volume when the unit is turned on.
Off  On
Off:  Sets normal volume.
On:  Sets your preferred volume.
Notes:
• 
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
• You can hear the changed volume regardless of your volume setting before opening the options 
menu if you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL 
level
Off On
Press  button to adjust the maximum volume.
Off  On
Off:  Sets auto maximum volume.
On:  Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” 
automatically becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• You can hear the changed volume regardless of your volume setting before opening the options 
menu if you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
INPUT lockOff   PC   INPUT1   INPUT2   INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 16).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
• In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value 
input in the single screen display mode.
•  When a dual input terminal board is attached, A or B is displayed depending on the selected input 
signal. (Ex. INPUT1A, INPUT1B)
Button lockOff  MENU&ENTER  On 
Off:  All the buttons at the bottom of the main unit can be used.
MENU & ENTER: Locks 
MENU and ENTER/ buttons on bottom face of main unit.
On:  Locks all the button on bottom face of main unit.
Sets Button lock with the unit buttons in the following procedure.
Off:  Press 
 four times→Press INPUT four times→Press  four times→Press ENTER/MENU & ENTER:  Press ENTER/ four times→Press  four times→Press INPUT four times→Press ENTER/On:  Press  four times→Press ENTER/ four times→Press  four times→Press ENTER/
Remocon 
User levelOff  User1  User2  User3 
Off:  You can use all of the buttons on the remote control.
User1:  You can only use , , , , , , ,  buttons on the remote 
control.
User2:
 You can only use , , buttons on the remote control.
User3: Locks all the buttons on remote control.
Advanced PIP
Off On
Off:  Sets normal two screen display mode (see page 19).
On:  Sets Advanced PIP mode (see page 20).
Notes:
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
• 
,  buttons are unavailable during Advanced PIP mode operation.
Options Adjustments
 Ofrecido por www.electromanuales.com
 
						

							40
Options
EnableOff-timer function
NormalInitial Power Mode0ID selectOffRemote IDOffSerial IDOffDisplay sizeOffStudio W/BOffStudio Gain
2/3
Item Effect Adjustments
Off-timer 
function
EnableDisable
Enable:  Enables the “Off-timer function”.
Disable:  Disables the “Off-timer function”.
Note:    When “Disable” is set, the Off-timer is cancelled.
Initial Power 
ModeNormal  Standby  On
Sets the power mode of the unit for when the power recovers from failure or after plugging off 
and in again.
Normal:  Power returns in as the same state as before the power interruption.
Standby:  Power returns in standby mode. (Power Indicator : red/orange)
On:    Power returns in power On. (Power Indicator : green)
Note:    When using multiple displays, “Standby” is preferred to be set in order to reduce a 
power load.
ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
Remote ID
Off On
Off:  Disables ID remote control functions. You can use normal remote control operations.
On:  Enable ID remote control functions.
Serial ID
Off On
Sets the panel ID Control.
Off:  Disables external control by the ID.
On:  Enables the external control by the ID.
Display size
Off On
Adjusts the image display size on screen.
Off:  Sets the normal image display size on screen.
On:  Sets the image display size approximately 95 % of the normal image display.
     Off        On
  
Notes:
• This setting is valid only when the input signals are as follows; 
  NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board 
(TY-FB9BD))
  525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 
1125/30p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi screen is selected.
• When Display size is set to “On”, Pos. /Size adjustment cannot be used.
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
Studio W/B
Off On
Off:  Nullify all the settings adjusted.
On:  Sets the colour temperature for TV studio.
Note:  Valid only when the low is set as colour temperature on screen adjustment.
Studio Gain
Off On
Sharpens the contrast for a better view when a part of the image is too light to see.
Off:  Disables “Studio Gain”.
On: Enables “Studio Gain”.
Note:  This setting is valid only when the input signals are as follows:
    Component Video, RGB (analog), SDI, HDMI
Options Adjustments
 Ofrecido por www.electromanuales.com