Panasonic Th 42pr10r Operating Instructions

							11
Power On / Off
Connecting the plug to the Wall Outlet.
Notes:
•  Main plug types vary between countries. The power plug shown 
at right may, therefore, not be the type fi tted to your set.
• When disconnecting the AC cord, be absolutely sure to 
disconnect the AC cord plug at the socket outlet fi rst.
Press the Power switch on the Plasma Display to turn the set 
on: Power-On.
Power Indicator: Green
Example: The screen below is displayed for a while after the 
Plasma Display is turned on (setting condition is an 
example).  
Press the 
 button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the 
 button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the 
   switch on the 
unit, when the Plasma Display is on or in standby mode.
Note: 
During operation of the power management function, the power indicator turns 
orange in the power off state. Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug securely to the 
Plasma Display with the clamper. 
(see page 8) 
Power IndicatorRemote Control Sensor
 Ofrecido por www.electromanuales.com
 
						

							MENUENTER/INPUTVOL
12
Basic Controls
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit 
will still consume some power 
as long as the power cord is still 
inserted into the wall outlet.)
• Standby .......... Red
• Power-ON ...... Green
• DPMS .............Orange (With PC input signal 
and during operation of PC’s 
screensaver.)
Main Power On / Off Switch
Normal Viewing Picture Setup
Sound Pos. /Size
Remote control sensor
SURROUND button
The surround setting switches on and off each time 
the SURROUND button is pressed.
The benefi  ts of surround sound are enormous. You 
can be completely enveloped in sound; just as if 
you were at a concert hall or cinema.
Note:
The surround settings are memorized separately 
for each Sound Mode (Normal, Dynamic, Clear).
On  Off
On Surround
INPUT button
(INPUT1, INPUT2, INPUT3 
and PC selection)
(see page 16)
MENU Screen ON / OFF
Each time the MENU button is pressed, the 
menu screen will switch. (see page 14)Volume Adjustment
Volume Up “+” Down “–” 
When the menu screen is displayed:
“+”: press to move the cursor up
“–”: press to move the cursor down
(see page 14)
Enter / Aspect button 
(see page 14, 17)
N button (see page 18, 21, 22, 23, 24)
POS. / SIZE button (see page 18)
PICTURE button (see page 21)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
Press to select INPUT1, INPUT2, INPUT3 and PC input 
SLOTS sequentially. (see page 16)
Sound mute On / Off (see page 24)
Numeric buttons
ASPECT button
Press to adjust the aspect. (see page 17)
MULTI Window buttons (see page 19)
 Ofrecido por www.electromanuales.com
 
						

							13 Basic Controls
Off  timer 90
2
3 1
PC4:3
Standby (ON / OFF) button
The Plasma Display must fi rst be plugged into the wall outlet and turned on at the power switch (see page 11).
Press ON to turn the Plasma Display On, from Standby mode. Press OFF to turn the Plasma Display Off to Standby 
mode.
SET UP button (see page 14, 15)
DIRECT INPUT buttons
Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to 
select the input mode.
This button is used to switch directly to INPUT mode.
These buttons can only display the slot which is installed. If you 
press the button whose slot is not installed, it automatically displays 
the current input signal.
When a dual input terminal board is attached, A or B is displayed 
depending on the selected input signal. (Ex. INPUT1A, INPUT1B)
Note:
Image retention (image lag) may occur on the plasma display panel 
when a still picture is kept on the panel for an extended period. The 
function that darkens the screen slightly is activated to prevent image 
retention (see page 45), this function is not the perfect solution to 
image retention.
Channel Adjustment 
You can use this button when U/V Tuner Board with Hospitality Port 
is installed (optional accessories). Refer to each Boards Operating 
Instruction for detail.
Volume Adjustment
Press the Volume Up “+” or Down “–” button to increase or decrease 
the sound volume level.
OFF TIMER button
The Plasma Display can be preset to switch to stand-by after a 
fi xed period. The setting changes to 30 minutes, 60 minutes, 90 
minutes and 0 minutes (off timer cancelled) each time the button 
is pressed.
When three minutes remain, “Off timer 3” will fl ash.
The off timer is cancelled if a power interruption occurs.
Digital Zoom (see page 25) Status button
Press the “Status” button to display the current system status.
Press to access 
Digital Zoom.
This displays an enlargement of the designated part of the 
displayed image.  ACTION button
Press to make
selections.
SOUND button
 (see page 24)R button (see page 15) 
Press the R button to return to previous menu screen.
30 60
090
POSITION 
buttons1   Input label
2 
 Aspect mode (see page 17)
3 
 Off timer
  The off timer indicator is 
displayed only when the off 
timer has been set.
The remote control is not included with this set. Available for purchase separately.
Object model : EUR7636090R
 Ofrecido por www.electromanuales.com
 
						

							14
1/2Picture
NormalNormaliseNormal
25
0
0
0
5 Brightness
Sharpness Picture Mode
Colour Contrast
Tint
2/2Picture
Advanced settings White balance
Colour ManagementNormal
Off
On
Advanced settings
NormalNormalise
0
0
0
0
0
0
2.2
Off W/B Low B Black extension
W/B High B
W/B Low R
AGC Gamma Input level
W/B High R
Sound
NormalNormaliseNormal
0
0
0
Off
Treble0
Mid Sound Mode
BalanceBass
Surround
Main Audio Out (PIP)
NormalNormalise
Pos. /Size
0000 V-Pos H-Pos
V-SizeH-Size
NormalNormalise
Pos. /Size
00000 V-Pos H-Pos
V-SizeH-SizeClock Phase
1/2
Signal
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD LanguageEnglish (
UK) Component/RGB-in select
RGB
Input label
Power save
Setup
2/2 Setup 
Screensaver 
MULTI DISPLAY Setup 
Set up TIMER 
PRESENT TIME Setup 
MENU
ENTER/INPUT
VOL
MENU
ENTER/INPUT
VOL
12
To Pos./Size adjust menu (see page 18)
During “RGB / PC” input signal.
During “AV(S Video)”, 
“Component” and “Digital” input 
signal.
To Advanced  settings
(see page 21, 22)Press to select 
“On”. To Picture adjust menu
 (see page 21)The MENU button on the unit can also 
be pressed.
Each time the MENU button is pressed, 
the menu screen will switch.
Normal Viewing Picture Setup
Sound Pos. /Size[ from the unit ]
1   Press to select.
2 
 Press to access each adjust 
screen.
1   Press to select.
To Sound adjust menu 
(see page 24)
On-Screen Menu Displays
Press to enter 
Advanced settings.
 Ofrecido por www.electromanuales.com
 
						

							15
Sync
P-NR
Signal
Auto
H-Freq.
V-Freq.kHz
Hz33.8
60.0
[ 
RGB ]
Cinema realityOff
OffCinema reality
P-NR
Signal
Off
Off
[ 
Component ]
3D Y/C Filter (NTSC)
Colour system
Signal
On
Auto
Cinema reality
Panasonic Auto (4 : 3)Off
4 : 3
[ 
AV  ]
P-NR
Off
Set up TIMER
POWER OFF Function
POWER OFF Time POWER ON Time POWER ON FunctionOff
0:00
Off
0:00 PRESENT  TIME    10:00
Set up TIMER
POWER OFF Function
POWER OFF Time POWER ON Time POWER ON FunctionOn
12:00
On
18:00 PRESENT  TIME    10:00
Set up TIMER
POWER OFF Function
POWER OFF Time POWER ON Time POWER ON FunctionOff
12:00
Off
18:00 PRESENT  TIME    10:00
PRESENT  TIME Setup 
Set
PRESENT  TIME99:99DAYMON PRESENT  TIME    MON  99:99
Cinema reality
P-NR
Signal
Off
Off
H-Freq.
V-Freq.kHz
Hz33.8
60.0
[ 
Digital ]
[ from the unit ]
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit Operating Time Periodic TimeWhite bar scroll
Interval
12:00
3:00
High
Off
Off PRESENT  TIME    15:00
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit Finish Time Start TimeWhite bar scroll
Time Designation
6:15
12:30
High
Off
Off PRESENT  TIME    15:00
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit Finish Time Start TimeWhite bar scroll
Time Designation
6:15
12:30
High
Off
Off PRESENT  TIME    15:00
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit Operating Time Periodic TimeWhite bar scroll
Interval
12:00
3:00
High
Off
Off PRESENT  TIME    15:00
MENU
ENTER/INPUT
VOL
2   Press to access 
each adjust 
screen.
Press the R button to return to 
previous menu screen.
Press to return to next menu screen.
To Signal screen for AV
(S Video) (see page 32, 33)To Signal screen for 
Component (see page 33)To Signal screen for RGB 
(see page 33, 34)To Signal screen for Digital 
(see page 33, 34)
Note : “Signal” setup menu displays different setting condition for each input signals. (see page 16) Note: 
Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
Press the R button to return 
to “Setup” menu. Press to select POWER ON 
Time / POWER OFF Time.
Press to Set up 
POWER ON Time / 
POWER OFF Time. To Set up Timer selection 
screen (see page 26, 27)
To PRESENT TIME Setup 
(see page 26)Press the R button to return 
to “Setup” menu.Press to Setup. Press to select Start Time / Finish Time 
(When Time Designation is selected).
Press to select Periodic Time / Operating Time 
(When Interval is selected). To setup Screensaver 
(see page 
28-30)
On-Screen Menu Displays
 Ofrecido por www.electromanuales.com
 
						

							16
.......(Japanese)
.......(Russian)
Русский .......(Chinese) Italiano Français Deutsch English(UK)
Español
ENGLISH(US)
1/2
Signal
PC
Off
Standby saveOff
Power managementOff
Auto power offOff
OSD LanguageEnglish (
UK) Component/RGB-in select
RGB
Input label
Power save
Setup
MENU
ENTER/INPUT
VOL
Swing up the door at “PULL”. Notes:
•  Selecting is also possible by pressing the INPUT button on the unit.
•  Input terminal will not be selected if the terminal board is not installed into the 
SLOT.
•  Select to match the signals from the source connected to the component/RGB 
input terminals. (see page 32)
•  In 2 screen display, the same input mode cannot be selected for the main picture 
and sub picture. Select the input signals to be connected by installing the optional Terminal Boards.
Press to select the input signal to be played back from 
the equipment which has been connected to the Plasma 
Display.
Input signals will change as follows:
INPUT1 INPUT2 PCINPUT3
Selecting the On-Screen Menu Language
Press to display the Setup menu.
Press to select the OSD Language.
Press to select your preferred language.
   Selectable languages
Selecting the input signal
Initial selections
 Ofrecido por www.electromanuales.com
 
						

							17
MENU
ENTER/INPUT
VOL
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema 
format picture.
Press repeatedly to move through the aspect options:
Mode Picture Explanation
4 : 3
4 : 3
3 4
4:3 will display a 4:3 picture at its standard 4:3 size.
Zoom
Zoom4
316
9Zoom mode magnifi es the central section of the picture.
16 : 9
16 : 94
316
916:9 will display the picture at its maximum size but with slight 
elongation.
Just
Just4
39 16
Just mode will display a 4:3 picture at its maximum size but with 
aspect correction applied to the center of the screen so that 
elongation is only apparent at the left and right edges of the screen. 
The size of the picture will depend on the original signal.
Panasonic
Auto
Panasonic Auto416
39The display will automatically become enlarged (depending on the 
picture source), allowing you to view the picture at its maximum 
size.
Notes:
• Panasonic Auto mode is designed to automatically adjust the 
aspect ratio to handle a mix of 16:9 and 4:3 program material. 
Certain 4:3 program material, such as stock market data screens, 
may occasionally cause the image size to change unexpectedly. 
When viewing such programs, it is recommended that the ASPECT 
be set to 4:3.
• If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9 
mode, the adjustment is not memorized. When exiting the mode, 
the screen will return to a former adjustment.
• Panasonic Auto can not be selected while BNC Dual Video 
Terminal Board (TY-FB9BD) is installed.
For an elongated imageImage is expanded
4
3Changes in 
accordance with 
the Panasonic Auto 
mode setting (see 
page 33).
For a 4:3 image
[from the unit]
4 : 3 16 : 94 : 3 Zoom 16 : 9
Panasonic Auto Just
The aspect mode changes each time the ENTER button is 
pressed.
Note: 
Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image 
retention to remain on the Plasma Display Panel. [During MULTI PIP Operations]
• Picture and Picture, Picture in Picture  :
• Others  : Aspect switching is not possible.
Notes:
•  For PC signal input, the mode switches between “4:3”, “Zoom” and “16:9” only.
•  For a 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p 
  signal input, the mode is set to “16:9” mode, and switching is not possible.
•  Panasonic Auto can be selected only during Video signal input.
•  The aspect mode is memorized separately for each input terminal.Note: 
When selecting an input slot that attaches BNC Dual Video Terminal 
Board (TY-FB9BD), Panasonic Auto cannot be selected.
 Ofrecido por www.electromanuales.com
 
						

							18
1
3 2
NormalNormalise
Pos. /Size
0000 V-Pos H-Pos
V-SizeH-Size
NormalNormalise
Pos. /Size
00000 V-Pos H-Pos
V-SizeH-SizeClock Phase
4
Press to display the Pos. /Size menu.
Press to select H-Pos / H-Size / V-Pos / V-Size / 
Clock Phase.
Press to adjust Pos. / Size.
Press to exit from adjust mode.
Notes:
•  Adjustment details are memorized separately for different input signal formats 
(Adjustments for component signals are memorized for 525 (480) / 60i · 60p, 
625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 
(1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/Digital signals are 
memorized for each frequency.) 
•  If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture 
position will shift up or down. This picture position movement cannot be 
controlled by the Picture Pos./Size function.
•  If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9 mode, the 
adjustment is not memorized. When exiting the mode, the screen will return 
to a former adjustment.During “RGB / PC” input signal.
During “AV(S Video)”, “Component” 
and “Digital” input signal.
H-PosAdjust the horizontal position.H-SizeAdjust the horizontal size.
V-PosAdjust the vertical position.V-SizeAdjust the vertical size.
Clock Phase
(RGB/PC in mode)Eliminate the fl ickering and distortion.
Adjusting Pos. / Size
While the Pos. / Size display is active, if either the N button on the remote control is pressed at any time or the ACTION 
( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
Helpful Hint (  / Normalise 
 Normalisation)
 Ofrecido por www.electromanuales.com
 
						

							19
ABABAB
BABABA
PC1
VIDEO2PC1
VIDEO2
VIDEO2
VIDEO1PC1
VIDEO2
A
A A
CB
B
B
D
[Picture out Picture]
Main picture Sub picture[Picture and Picture] [Picture in Picture]
[Example]
Input modes switching is possibleMain picture label is bright Sub picture label is bright
Picture is changed Main picture label is changed
Sub picture label is changed
Main picture Sub picture Main picture Sub picture
Normal
Viewing
MULTI PIP
Press repeatedly.
Each time pressing this button main picture and sub picture will be displayed 
as follows below.
Press to swap main 
picture and sub picture.
Press to select the input mode.
Under main Picture and sub picture display, 
select the picture which you would like to 
change input modes.
Notes:
•  The sub picture sound is heard while a sub 
picture operation is underway.
• The sub picture operation automatically 
returns to the main picture operation if 
a sub picture operation has not been 
performed for about 5 seconds or if any 
of the remote control buttons is pressed 
(except 
 
button).
Press to move the sub picture.
Each time the location of the sub picture will be moved.
Notes:
• This button is effective only in the picture in picture. 
• The sub picture may be hidden by the on screen display, depending on its position. Press to change input signal.
Notes:
•  If “INPUT lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.
•  Sound output is from the picture which is selected in Audio Out (PIP) (See page 24).
•  In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.
•  The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of 
the pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals 
displayed on the main picture and depending on the 2-picture display mode.
•  Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail.
• 
Computer screen picture is displayed in a simplifi ed format, and it may not be possible to discern details on them satisfactorily.
•  Following combinations of two analog signals cannot be displayed simultaneously;
  Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB)
 Ofrecido por www.electromanuales.com
 
						

							20
1
2
3
5
4
6
One screen  Advanced PIP
Main screen Sub screen
7
Options 
On Weekly Command Timer Onscreen display Off Initial INPUT Initial VOL level 
1/3 
 
Off  Off 
0  0 Maximum VOL level Off INPUT lock Off Button lock Off Remocon User level Off Advanced PIP 
1/3Options
Off-timer function
INPUT lock
Studio W/B
Advanced PIP
Display size Initial VOL level
Maximum VOL level Initial INPUT Onscreen display
Off
Off
Off
Off Enable
On
Off
0
Off Off
0
123
654
Advanced PIP
Press to display the Setup menu.
Press to select “OSD Language”.
Press repeatedly.
Each time pressing this button main picture and sub picture will be displayed as above.
(When Advanced PIP is On)
Notes:
•  Advanced PIP corresponding signalNote:
To use 
, , ,  buttons for the screen operations, follow the procedures in the previous page.
•  If “INPUT lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.
•  Sound output is from the picture which is selected in Audio Out (PIP) (See page 24).
•  In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.
•  The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of 
the pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals 
displayed on the main picture and depending on the 2-picture display mode.
•  Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail.
• 
Computer screen picture is displayed in a simplifi ed format, and it may not be possible to discern details on them satisfactorily.
•  Following combinations of two analog signals cannot be displayed simultaneously;
  Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB)
•  Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.Sub screen Main screen
NTSC, PAL, SECAM (tuner, video)
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 
1125/50i, 1250/50i (Component Video, RGB, DVI, SDI, 
HDMI)640x480@60Hz, 852x480@60Hz, 1024x768@60Hz, 
1366x768@60Hz (RGB, DVI, HDMI)
1280x768@60Hz (DVI) TH-42PG10R TH-37PR10R, TH-42PR10R Press and hold until the Options menu is displayed.
Press to select Advanced PIP.
Press to adjust the 
menu.
Off :   Sets normal 
two screen 
display mode 
(see page 19).
On :   
Sets Advanced 
PIP mode.
Press to exit from 
Options menu.
 Ofrecido por www.electromanuales.com