Panasonic Th 32lhd7uy Operating Instructions

							11
Connections
SERIAL Terminals connection
Notes:
•  Use the RS-232C cable to connect the computer to the LCD Display.
•  The computer shown is for example purposes only.
•  Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface specifi cation, so that the LCD Display can be controlled by a 
computer which is connected to this terminal.
The computer will require software which allows the sending and receiving of control data which satisfi es the conditions 
given below. Use a computer application such as programming language software. Refer to the documentation for the 
computer application for details. The SERIAL terminal is used when the LCD Display is controlled by a computer.
Communication parameters
Basic format for control data
The transmission of control data from the computer 
starts with a STX signal, followed by the command, 
the parameters, and lastly an ETX signal in that order. 
If there are no parameters, then the parameter signal 
does not need to be sent.
Notes:
•  If multiple commands are transmitted, be sure to wait 
for the response for the fi rst command to come from 
this unit before sending the next command.
•  If an incorrect command is sent by mistake, this unit will 
send an “ER401” command back to the computer.With the power off, this display responds to PON command 
only.
9 8 7 6
5 3 2 14
SERIAL
Pin layout for RS-232C  COMPUTER
RS-232C 
Straight cable
D-sub 9pFerrite core
(large size)
(supplied)
Installing the ferrite core 
(Large size)
Open
Start
(02h)3-character
command (3 bytes)Colon Parameter(s)
(1 - 5 bytes)End
(03h) STX C1 C2 C3 P1 P2 P3 P4:P5ETX
Command
Command
PON
POF
AV L
AMT
IMS
DAMControl details
Power ON
Power OFF
Volume 00 - 63
Audio MUTE OFF
Audio MUTE ON
Input select (toggle)
Slot1 input
Slot2 input
PC input
Screen mode select (toggle)
NORMAL (4 : 3)
ZOOM
FULL
JUST
Panasonic AUTO Parameter
None
None
**
0
1
None
SL1
SL2
PC1
None
NORM
ZOOM
FULL
JUST
SELF
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
Flow controlRS-232C compliant
Asynchronous
9600 bps
None
8 bits
1 bit
-
2
3
4
5
6
7
8
91
RS-232C Conversion cable
 D-sub 9-pin female  Details
    R X D
   T X D
   GND
    •  Non use  
  
  Shorted 
   
 • NC
Less than 3” 15/16(10 cm)
 
						

							12
SLOT1
VIDEO INVIDEO OUTAUDIO
INRLAVS VIDEO IN
PC    IN
VIDEO INAUDIO
INL
RS VIDEO INSLOT 2AVVD HDPR/CR/R PB/CB/BY/GR   AUDIO   LCOMPONENT/RGB INSLOT 1AUDIOPC  IN SERIALVIDEO OUT
VIDEO
OUTVIDEO IN
S VIDEO
OUT
AUDIO
OUT RL
AUDIO
OUT Y,   P
B,  PR,
OUT
RR
PB
Y
L
R
COMPONENT VIDEO OUT
SLOT2
COMPONENT/RGB INPR/CR/R PB/CB/BVD HDY/GR   AUDIO   L
DVD
VIDEO INAUDIO
INL
RS VIDEO INSLOT 2AVVD HDPR/CR/R PB/CB/BY/GR   AUDIO   LCOMPONENT/RGB INSLOT 1AUDIOPC  IN SERIALVIDEO OUTVIDEO INVIDEO OUT
COMPONENT/RGB IN
PR/CR/R PB/CB/BVD HDY/GR   AUDIO   L
or Notes:
•  Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT”. (see page 29)
•  Additional equipment, cables and adapter plugs shown are not supplied with this set.
Notes:
•  Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “RGB”. (see page 29)
•  Additional equipment, cables and adapter plugs shown are not supplied with this set.S VIDEO VCR
CAMCORDER
VCRMONITOR RCA-BNC
adapter plug Example of input signal source
Digital TV-SET-TOP-BOX 
(DTV-STB) 
AV & COMPONENT connection
RGB signal (R, G, B, HD, VD)
Connections
Example of input signal source
ComputerRGB CamcorderFerrite core
(large size)
(supplied)
Installing the ferrite core (Large size)
Open
Less than
3” 15/16(10 cm)
 
						

							13
Power ON / OFF 
When the POWER is turned on for the fi rst 
time, the LANGUAGE selection screen is 
displayed.
From the second time on, language selection 
can be done from the setup menu. (see 
page 18)
Select the desired language using the   
or   
button and press the ACTION (  )  
button.From the second time on, the screen 
shown below is displayed for a while 
(setting condition is an example).
English (UK)
Deutsch
Français
Italiano
Español
ENGLISH (US)
OSD LANGUAGE
SELECT SET
PCFULL
Connecting the plug to the Wall Outlet
Press the Power switch on the LCD Display to turn the set on: 
Power-On.
Power Indicator: Green
Example: The screen below is displayed for a while after the 
LCD Display is turned on. (setting condition is an 
example.) Connecting the AC cord plug to the LCD Display.
Fix the AC cord plug securely to the LCD Display with 
the clamper. (see page 9) 
VIDEO INAUDIO
INL
RS VIDEO INSLOT 2AVVD HDPR/CR/R PB/CB/BY/GR   AUDIO   LCOMPONENT/RGB INSLOT 1AUDIOPC  IN SERIALVIDEO OUT
TH-32LHD7
INPUT MENU ENTER/+/ VOL-/TH-32LHD7
Power Indicator
Remote Control
Sensor
Press the 
   button on the remote control to turn the LCD Display off.
  Power Indicator: Red (standby)
Press the 
   button on the remote control to turn the LCD Display on.
  Power Indicator: Green
Turn the power to the LCD Display off by pressing the 
   switch on the unit, when 
the LCD Display is on or in standby mode.
Note: 
During operation of the power management function, the power indicator turns 
orange in the power off state.
INPUT
SURROUND
VOL
NR
PICTURE
SOUNDSET UP
ASPECT PICTURE
POS. /SIZE
MULTI
PIPSWAP SELECT MOVEZOOM
 
						

							14
INPUT MENU ENTER/+/ VOL-/
TH-32LHD7
Main Power On / Off Switch
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit 
will still consume some power 
as long as the power cord is still 
inserted into the wall outlet.)
• Standby 
    ..... Red
• Power-ON ...... Green
• DPMS ............. Orange (With PC input signal.)Volume Adjustment
Volume Up “+” Down “–” 
When the menu screen is 
displayed:
“+” : press to move the cursor up 
“–” : press to move the cursor down
(see page 16)
Enter / Aspect button 
(see page 16, 19)
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen 
will switch. (see page 16)
INPUT button
(INPUT1, INPUT2 and PC IN selection)
(see page 18)Normal Viewing PICTURE SETUP
SOUND PICTURE POS. /SIZE
Basic Controls
Status button
1   Input label
2 
 Aspect mode (see page 19)
3 
 Off timer
  The off timer indicator is displayed only when the 
off timer has been set. Press the “Status” button to display the current 
system status.
OFF  TIMER 90
1
2
3 PCNORMALN button (see page 20, 22, 23, 24)
PICTURE button (see page 22)
MULTI Window buttons (see page 21)
PC button
Press the “PC” input mode selection button to select the 
PC input mode.
This button is used to switch directly to PC input 
mode.
Remote control sensor C.A.T.S. sensor
C.A.T.S. (Contrast Automatic Tracking System)
C.A.T.S. automatically senses the ambient light conditions and adjusts the brightness and gradation accordingly, to optimise 
contrast. (Effective when PICTURE MENU is set to AUTO.)
 
						

							15
DISPLAY
INPUT
SURROUND
VOL
NR
PICTURE
SOUNDSET UP
ASPECT PICTURE
POS. /SIZE
OFF TIMER
PC
MULTI
PIPSWAPSELECTMOVEZOOM
Basic Controls
SURROUND button
The surround setting switches on and off each time the SURROUND 
button is pressed.
The benefi ts of surround sound are enormous. You can be completely 
enveloped in sound; just as if you were at a concert hall or cinema.
Note:
The surround settings are memorized separately for each AUDIO MENU 
(STANDARD, AUTO). Standby (ON / OFF) button
The LCD Display must fi rst be plugged into the wall outlet and turned on at the power switch (see page 13).
Press this button to turn the LCD Display On, from Stanby mode. Press it again to turn the LCD Display Off 
to Stanby mode.
ON  OFF
INPUT button
(INPUT1, INPUT2 and PC IN selection)
Press to select INPUT1, INPUT2 and PC IN input SLOTS sequentially. 
(see page 18)
Sound mute On / Off (see page 24)
Volume Adjustment
Press the Volume Up “+” or Down “–” button to increase or decrease 
the sound volume level.
R button (see page 17) 
Press the R button to return to previous menu screen.
ACTION button
Press to make selections.
POSITION buttons
SOUND button (see page 24)
SET UP button 
(see page 16, 17)
PICTURE POS. / SIZE button
(see page 20)
ASPECT button
Press to adjust the aspect.
 (see page 19)
OFF TIMER button
The LCD Display can be preset to switch to stand-by after a fi xed 
period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 
0 minutes (off timer cancelled) each time the button is pressed.
When three minutes remain, “OFF TIMER 3” will fl ash.
The off timer is cancelled if a power interruption occurs.
Digital Zoom (see page 25)
Press to access
Digital Zoom.
This displays an enlargement 
of the designated part of the 
displayed image. 
ON SURROUND
ZOOM
MOVE
30 60
090
 
						

							16
DISPLAY
INPUT
SURROUND
VOL
NR
PICTURE
SOUNDSET UP
ASPECT PICTURE
POS. /SIZE
OFF TIMER
PC
MULTI
PIPSWAPSELECTMOVEZOOM
Normal Viewing PICTURE SETUP
SOUNDPICTURE POS. /SIZE
On-Screen Menu Displays
The MENU button on the unit can also be 
pressed.
Each time the MENU button is pressed, the 
menu screen will switch.
0
0
0
0
0
0
2.2 W/B LOW B BLACK EXTENSION
W/B HIGH B
W/B LOW R
AGC GAMMA INPUT LEVEL
W/B HIGH R
ADVANCED SETTINGS
NORMALNORMALIZE
OFF
0
0
0
SOUND
NORMALNORMALIZESTANDARD
OFF TREBLE AUDIO MENU
BALANCEBASS
SURROUND
NORMALNORMALIZE
PICTURE POS. /SIZE
V-POS H-POS
V-SIZEH-SIZE
NORMALNORMALIZE
PICTURE POS. /SIZE
V-POS
H-POS
V-SIZEH-SIZE
CLOCK PHASE
During “VIDEO (S VIDEO)”,
 “COMPONENT” and “DVI” input signal.
To PICTURE POS./SIZE adjust menu (see page 20)
During “RGB/PC” input signal. To PICTURE adjust menu
(see page 22)
To ADVANCED  SETTINGS
(see page 22, 23)
To SOUND adjust menu
 (see page 24)Press to select  
“ON”.
Press to enter 
ADVANCED 
SETTINGS.
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
2/2SET UP
SET UP TIMER
PRESENT TIME SETUP
[ from the unit ]
1   Press to select .
INPUT MENU ENTER/+/ VOL-/
1/2PICTURE
NORMALNORMALIZESTANDARD
25
0
0
0
3 BRIGHTNESS
SHARPNESS PICTURE MENU
COLOR PICTUREBACK LIGHT
TINT20
2/2
ADVANCED SETTINGS COLOR TEMP
COLOR MANAGEMENTNORMAL
OFFON
PICTURE
1  Press to select.
2   Press to access each adjust 
screen.
INPUT MENU ENTER/+/ VOL-/
12
 
						

							17
To SIGNAL screen for RGB 
(see page 30, 31) To SIGNAL screen for VIDEO
(S VIDEO)  (see page 29, 30)To SIGNAL screen for
 COMPONENT (see page 30)
2  Press to access 
each adjust 
screen.
Press the R button to return 
to previous menu.
Press the R button to return to 
“SET UP” menu. Press to select POWER ON 
TIME / POWER OFF TIME.
Press to set up POWER ON 
TIME / POWER OFF TIME. To SET UP TIMER selection 
screen. (see page 26, 27)
To PRESENT TIME SETUP.
(see page 26)Press to return to next menu 
screen.[ from the unit ]
SYNC
VIDEO NR
SIGNAL
AUTO
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[ 
RGB ]
3 : 2 PULLDOWNOFF
OFF
3 : 2 PULLDOWN
VIDEO NR
SIGNAL
OFF
OFF
 [ 
COMPONENT ]
3D Y/C FILTER (NTSC)
COLOR SYSTEM
SIGNAL
ON
AUTO
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)OFF
NORMAL
[ 
VIDEO ]
VIDEO NR
OFF
0:00
0:00
SET UP TIMER
POWER OFF FUNCTION
POWER OFF TIME POWER ON TIME POWER ON FUNCTION
OFF
OFF PRESENT  TIME OF DAY  99:99
99:99
PRESENT  TIME SETUP
PRESENT  TIME OF DAY    99:99
SET
PRESENT  TIME OF DAY
0:00
0:00
SET UP TIMER
POWER OFF FUNCTION
POWER OFF TIME POWER ON TIME POWER ON FUNCTION
OFF
OFF PRESENT  TIME OF DAY    99:99
0:00
0:00
SET UP TIMER
POWER OFF FUNCTION
POWER OFF TIME POWER ON TIME POWER ON FUNCTION
OFF
OFF PRESENT  TIME OF DAY    99:99
3 : 2 PULLDOWN
VIDEO NR
SIGNAL
OFF
OFF
H-FREQ.
V-FREQ.kHz
Hz33.8
60.0
[ 
Digital ]
To SIGNAL screen for DVI 
(see page 30, 31)
Note:  “SIGNAL” setup menu displays a 
different setting condition for each 
input signal. (see page 18)
On-Screen Menu Displays
R
R
INPUT MENU ENTER/+/ VOL-/
 
						

							18
Initial selections
Selecting the On-Screen Menu Language Selecting the input signal
Press to display the SET UP menu.
Press to select OSD LANGUAGE.
Press to select your preferred language.
   Selectable languages
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
Select the input signals to be connected by installing the optional Terminal Boards.
Press to select the input signal to be played back from 
the equipment which has been connected to the LCD 
Display.
Input signals will change as follows:
Notes:
•  Selecting is also possible by pressing the INPUT button on the unit.
•  Input terminal will not be selected if the terminal board is not installed into the SLOT.
•  Select to match the signals from the source connected to the component/RGB input 
terminals. (see page 29)
•  In 2 screen display, the same input mode cannot be selected for the main picture and 
sub picture.INPUT1 INPUT2 PC IN
INPUT
INPUT MENU ENTER/+/ VOL-/
INPUT MENU ENTER/+/ VOL-/TH-32LHD7
SURROUND
VOL
NR
PICTURE
SOUNDSET UPINPUT
MULTI
PIPSWAP SELECT MOVEZOOM
SET UP
.......(Japanese) .......(Chinese) Italiano Français Deutsch English(UK)
Español
ENGLISH(US)
INPUT
SURROUND
VOL
N
PICTURE
SOUND
R
MULTI
PIPSWAP SELECT MOVE
SET UP
ZOOM
 
						

							19
ASPECT Controls
The LCD Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format 
picture.
Press repeatedly to move through the aspect options:
Notes:
•  For PC signal input, the mode switches between “NORMAL”, “ZOOM” and “FULL” only.
•  For a 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p signal input during 
“COMPONENT”,“RGB” and “DVI” input signal, the mode is set to “FULL” mode, and switching is not possible.
•  Panasonic AUTO can be selected only during Video signal input.
•  The aspect mode is memorized separately for each input terminal  (INPUT1, INPUT2 and PC IN).
Mode Picture Explanation
NORMAL
NORMAL
3 4
NORMAL will display a 4:3 picture at its standard 4:3 size.
ZOOM
ZOOM4
316
9ZOOM mode magnifi es the central section of the picture.
FULL
FULL4
316
9FULL will display the picture at its maximum size but with slight 
elongation.
JUST
4
39 16
JUSTJUST mode will display a 4:3 picture at its maximum size but with aspect 
correction applied to the center of the screen so that elongation is only 
apparent at the left and right edges of the screen. The size of the picture 
will depend on the original signal.
Panasonic
AUTO
Panasonic AUTO416
39The display will automatically become enlarged (depending on the 
picture source), allowing you to view the picture at its maximum size.
Notes:
•  Panasonic AUTO mode is designed to automatically adjust the aspect 
ratio to handle a mix of 16:9 and 4:3 program material. Certain 4:3 
program material, such as stock market data screens, may occasionally 
cause the image size to change unexpectedly. When viewing such 
programs, it is recommended that the ASPECT be set to NORMAL.
•  If adjusting the PICTURE V-POS/V-SIZE in Panasonic AUTO with FULL 
mode, the adjustment is not memorized. When exiting the mode, the 
screen will return to a former adjustment.
For an elongated imageImage is expanded
4
3Changes in 
accordance with the 
Panasonic AUTO 
mode setting (see 
page 30).
For a 4:3 image
The aspect mode changes each time the ENTER button 
is pressed.
[During MULTI PIP Operations]
•  Picture and Picture, Picture in Picture  :
•  Others  :  Aspect switching is not possible. [from the unit]
INPUT
SURROUND
VOL
NR
PICTURE
SOUNDSET UP
ASPECT PICTURE
POS. /SIZE
MULTI
PIPSWAP SELECT MOVEZOOM
ASPECT
INPUT MENU ENTER/+/ VOL-/
NORMAL ZOOM FULL
Panasonic AUTO JUST
NORMAL FULL
 
						

							20
Adjusting PICTURE POSITION / SIZE
NORMALNORMALIZE
PICTURE POS. /SIZE
V-POS H-POS
V-SIZEH-SIZE
CLOCK PHASE
1Press to display the PICTURE POS. /SIZE menu.
Press to select H-POS / H-SIZE / V-POS / V-SIZE / 
CLOCK PHASE.
Press to adjust POS. / SIZE.
Press to exit from adjust mode.
During “VIDEO (S VIDEO)”,
“COMPONENT” and “DVI” input signal.
During “RGB / PC” input signal.
3 2
Notes:
• Adjustment details are memorized separately for different input signal formats 
(Adjustments for component signals are memorized for 525 (480) / 60i · 60p, 625 
(575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 
750 (720) / 60p · 50p each, and RGB/PC/DVI signals are memorized for each 
frequency.) 
•  If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position 
will shift up or down. This picture position movement cannot be controlled by the 
PICTURE POS. / SIZE function.
•  If adjusting the PICTURE V-POS / V-SIZE in Panasonic AUTO with FULL mode, 
the adjustment is not memorized. When exiting the mode, the screen will return 
to a former adjustment.
While the PICTURE POS. / SIZE display is active, if either the N button on the remote control is pressed at any time or 
the ACTION  (  ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
Helpful Hint ( 
N
 
 / NORMALIZE 
 Normalization)
Adjust the horizontal size.
Adjust the vertical size. H-POS
V-POSAdjust the horizontal position.
Adjust the vertical position.H-SIZE
V-SIZE
CLOCK PHASE
(RGB/PC in mode)Eliminate the fl ickering and distortion.
4
NORMALNORMALIZE
PICTURE POS. /SIZE
V-POS H-POS
V-SIZEH-SIZE
NR
INPUT
SURROUND
VOL
PICTURE
SOUNDSET UP
ASPECT PICTURE
POS. /SIZE
OFF TIMER
PC
MULTI
PIPSWAP SELECT MOVEZOOM
R
PICTURE
POS. /SIZE