Panasonic Shaver Es Lt7 Operating Instructions

11
Operation and display of the switch lock
 
► Locking the power switch
1. Press the power 
switch once and 
then release.
 
• The shaver 
starts operating. 2.
 Press the power 
switch for more 
than 2 seconds 
when the shaver 
is operating.
 
• The shaver will 
stop operating. 3.
 Release the 
power switch.
The switch lock 
lamp is off. The switch lock 
lamp will light up.The switch lock 
lamp will turn off 
after 5 seconds.
 
► Unlocking the power switch
1. Press the power switch for 
more than 2...

12
Charging the shaver
Charging using the self-cleaning recharger
1
1Insert the appliance plug into 
the self-cleaning recharger.
2
2Remove the protective cap 
while pressing the side of 
the cap.
 
• Turn the shaver off before 
removing the protective cap.
3
3Slowly insert the shaver into 
the self-cleaning recharger 
taking care not to damage 
the system outer foil.
1
3
4
 
• Wipe off any water droplets on the main body rear terminals.
4
4Plug in the adaptor into a household outlet. 
• The “Charge”...

13
Charging without the self-cleaning recharger
1
1Insert the appliance plug into 
the shaver.
 
• Turn the shaver off before inserting.
2
2Plug in the adaptor into a 
household outlet.
 
• Wipe off any water droplets on the 
appliance socket.
1 2
3
3Disconnect the adaptor after charging is 
completed.
Note
You cannot operate the shaver while charging.
Using the shaver
1
1Press the power switch. 
• The power cannot be turned on when the switch lock lamp 
() blinks, as the power switch is locked.  
Press...

14
 
• Depending on the beard thickness or the amount of beard 
trimmings in the shaver head, the shaving sensor may not react 
and the driving sound may not change. This is not abnormal.
 
• The shaving sensor may not respond depending on the type of 
the shaving gel and shaving foam, but this is normal.
 
• The shaving sensor may not respond when the remaining battery 
capacity is low. If this happens, recharge the shaver.
 
• Avoid the following situations to prevent damaging the system 
outer foil....

15
Reading lamps when using
While using
Approximate amount of battery capacity is 
displayed. 
• It will turn off approximately 5 seconds after 
operating the power switch.
 
• The shaving sensor lamp () glows.
When the battery capacity is low
“10%” appears and “” blinks.
 
• You can shave 2 to 3 times after “10%” appears. (This will differ 
depending on usage.)
 
• The shaver can be used for approximately 2 weeks with a full 
charge.  
(Based on one 3‑minute dry‑shave use per day until the battery 
is...

16
4
4Pour tap water ( 1
) and 
detergent ( 2
) into the 
cleaning liquid unit.
 
• Do not let the water rise 
above the maximum water 
line. This may cause the 
cleaning liquid to spill.
 
 
• Pour the entire packet of detergent (approximately 15 mL).
5
5Attach the cleaning liquid unit. 
• Immediately wipe up any cleaning liquid 
that has been spilt.  
Be careful not to drop cleaning liquid 
onto leather products or wooden floors 
as it may cause discoloration.
6
6Press the top of the self-
cleaning...

17
5
5Remove the adaptor after the selected mode is 
completed.
Mode
Time required (guide)
1  Charge Charge
0 to 60 min
2  AUTO Clean
10 min Dry
80 min Charge
0 to 60 min
 
• It is not possible to change the mode after the 
“AUTO” mode has started.
3  Dry/Charge Dry
180 min Charge
0 to 60 min
 
• It is possible to change to the “AUTO” mode 
even after the “Dry/Charge” mode has started.
 
• The drying time may increase in an ambient temperature 
approximately 15 °C (59 °F) or lower.  
The Clean or Dry...

18
 
► Drying the shaver with the self-cleaning recharger1. Attach the outer foil section to the shaver.
2.  After removing excess moisture, wipe any remaining droplets 
from the system outer foil, grip, and main body rear terminals.
3.  Dry the shaver with self‑cleaning recharger using “Dry/Charge” 
mode.
Note
Do not use the self‑cleaning recharger while droplets, soap, or 
shaving gel remain on the shaver.  
Doing so may change the concentration level or constituent of 
the cleaning liquid in the...

19
Cleaning the self-cleaning recharger
 
• Do not wash the self‑cleaning recharger unit with water.  
Also, do not wipe with thinners, benzine, alcohol etc.  
Doing so may result in malfunction.
 
• The cleaning liquid unit and filter can be washed with water.
 
• Remove the AC adaptor from the self‑cleaning recharger.
 
• We recommend cleaning the self‑cleaning recharger each time 
you change the cleaning liquid.
1.  Be sure to remove the cleaning liquid unit 
from the self‑cleaning recharger.
 
• Some...

20
Troubleshooting
Perform the following actions.
If the problems still cannot be solved, contact the store where 
you purchased the unit or a service center authorized by 
Panasonic for repair.
 
► Self-cleaning recharger
Problem Action
The blade has not been 
thoroughly washed.
Do not add detergent and water 
except when replacing the 
cleaning liquid.
Doing so may deteriorate the 
cleaning function. (See page 16.)
After cleaning, oil‑like droplets 
may remain on the outside of the 
foil frame. This is...