Panasonic Sdr S7 Operating Instructions Manual

							91VQT1R00
ProblemWhat to check
The display 
changes suddenly.If the demo (camera introduction) video starts, set 
[DEMO MODE] to [OFF]. (P.84)
Indications 
(remaining pictures, 
elapsed time, etc.) 
do not appear on 
the LCD monitor.When [DISPLAY] of the [SETUP] menu is set to 
[OFF], indications other than warnings and the date 
do not appear.
Pictures cannot 
be recorded even 
though the SD card 
is properly inserted.●  Is the SD card write-protected? (P.19)
●  Is the SD card full? Either delete unnecessary 
scenes or insert a new card. (P.56)
●  Is the unit in a recording mode?
●  Is the card/battery door open?
Motion picture 
recording stops on 
its own.●  Are you using an applicable SD card? (P.18)
●  Even with applicable SD cards, recording may stop 
when using an SD card on which data has been 
written many times. 
Copy the data to a computer, then format the SD 
card on this unit. (Formatting deletes all data on the 
SD card.)
Still pictures come 
out like mosaics.When [PICT. QUALITY] is set to [] and detailed 
subjects are recorded, pictures come out like 
mosaics. Set to [
] when recording. (P.35)
The unit does not 
focus automatically.●  Is the unit set to manual focus? Press the [AUTO] 
button to set auto focus.
●  Are you recording a scene that is hard to focus 
automatically? 
Focus the subject manually. (P.44)
Audio is not output.Is the volume set low? (P.52) 
						

							92VQT1R00
ProblemWhat to check
The sound of the 
motor is being 
recorded.This is an operating sound of the unit; there is nothing 
wrong with the unit.
Images do not 
appear on TV or 
appear stretched 
in the vertical 
direction.●  Does the input mode on the TV match the connected 
terminals? 
Set input to the connected terminals as explained in 
the TV’s operating instructions.
●  Set [TV ASPECT] to match the connected TV. (P.60)
Data cannot be 
deleted.●  Is the scene locked? 
Unlock the scene. (P.58)
●  Scenes whose thumbnails have a  cannot be 
deleted. If the data is unnecessary, format the SD 
card (P.58). Formatting deletes all data on the SD 
card.
●  Is the SD card write-protected? (P.19)
Images on the SD 
card do not look 
normal.The scene may be damaged. Scenes can be 
damaged by static electricity and electromagnetic 
waves. Save important data on a computer, etc.
The SD card cannot 
be used even after 
formatting with this 
unit.This unit or the SD card may be broken. Consult the 
dealer from which you purchased the unit. For SD 
cards applicable with this unit (P.18)
The unit does not 
recognize the SD 
card when inserted.Was the SD card formatted on the computer? 
Format SD cards with the unit.
Formatting deletes all data on the SD card. Data 
cannot be restored afterwards. (P.58)
Others4Troubleshooting (cont.)  
						

							93VQT1R00
ProblemWhat to check
The indication 
disappears, the 
display does not 
work or cannot be 
operated.●  Is the unit connected to a computer? 
When connected to a computer, the unit cannot be 
operated from the unit itself.
●  Shut the power off. If power does not shut off, eject 
the SD card, remove and then reinsert the battery 
(disconnect and reconnect the AC adaptor), and 
turn back on. If the unit still does not work right, 
disconnect the power supply and consult the dealer 
from which you purchased the unit.
The SD card is not 
recognized when 
inserted into other 
devices.Check the supported SD cards in the device’s 
operating instructions.
The computer does 
not recognize the 
unit even when 
connected with USB 
cable.●  While the menu appears on the LCD monitor, the 
USB function screen does not appear even if the 
USB cable is connected. Close the menu, then 
connect the USB cable.
●  Is the AC adaptor connected?
●  If the computer has multiple USB terminals, try using 
another terminal.
●  Check the operating environment. (P.72)
●  Disconnect the USB cable, shut the power off and 
turn back on, then reconnect the cable.
After disconnecting 
the USB cable, 
an error message 
appears on the 
computer.●  For Windows
To safely disconnect the USB cable, click the ( 
or ) icons in the task tray, and do as instructed by 
displayed messages.
●  For Macintosh
Drag the unit icon to the Trash, then disconnect the 
USB cable.  
						

							94VQT1R00
ProblemWhat to check
[ERROR 
OCCURRED.
PLEASE TURN UNIT 
OFF, THEN TURN 
ON AGAIN.] appears 
on the LCD monitor.●  The unit detected an error. To protect data, eject 
the SD card and set the mode dial to [OFF]. Power 
shuts off about 1 minute later.
●  If the same message is displayed repeatedly after 
turning power back on, the unit needs servicing. 
Disconnect the power supply and consult the dealer 
from which you purchased the unit. Do not attempt 
to repair the appliance by yourself.
The audio does not 
output for a motion 
picture copied with 
a DVD burner.If [AUDIO REC] (P.84) is set to [MPEG] for recording, 
audio may not be output with some playback devices.
Set to [DOLBY] when recording.
The PDF file of 
the MotionSD 
STUDIO operating 
instructions does 
not open.Is Adobe Acrobat Reader 5.0 or later, or Adobe 
Reader 7.0 or later installed in the computer?
Adobe Acrobat Reader 5.0 or later, or Adobe Reader 
7.0 or later is required to view the PDF file of the 
MotionSD STUDIO operating instructions.
[DISC IS 
UNUSABLE.
CHECK DISC.] 
appears on the LCD 
monitor.A disc which cannot be used or a disc which cannot 
be written on has been inserted into the DVD burner. 
Use a new disc.
Others4Troubleshooting (cont.)  
						

							95VQT1R00
ProblemWhat to check
A function cannot 
be used or selected.Because of specifications, this unit has functions that 
cannot be used simultaneously. 
Examples:
Function Condition
Digital zoom●  When in still picture recording 
mode
Fade●  When in still picture recording 
mode
●  While the PRE-REC function 
is being set
MagicPix●  When in still picture recording 
mode
●  During recording 
(Cannot set nor cancel)
●  While the PRE-REC function 
is being set 
(Cannot set nor cancel)
Backlight 
compensation●  While setting iris or gain
●  While using MagicPix
Soft skin mode 
(Set and cancel)●  During recording
●  While the PRE-REC function 
is being set
Help mode
Image stabilizer●  When in still picture recording 
mode
●  While using MagicPix
Scene mode●  When in auto recording mode
●  While using MagicPix
Changes to white 
balance mode●  When using digital zoom
●  While using MagicPix
Changes to 
shutter speed/
iris or gain●  When using scene mode
●  While using MagicPix
When [INITIAL SET] is executed from the SETUP 
menu, all the settings except for [LANGUAGE] 
and [CLOCK SET] will be restored to the defaults 
established at the time of purchase, and it will then 
become possible to select functions. (P. 84) 
						

							96VQT1R00
When using the unit
●  Keep the SD Video Camera as far away as possible from electromagnetic 
equipment (such as microwave ovens, TVs, video games etc.).
  •  If you use the SD Video Camera on top of or near a TV, the pictures and 
sound on the SD Video Camera may be disrupted by electromagnetic wave 
radiation.
  •  Do not use the SD Video Camera near cell phones because doing so may 
result in noise adversely affecting the pictures and sound.
  •  Recorded data may be damaged, or pictures may be distorted, by strong 
magnetic fields created by speakers or large motors.
  •  Electromagnetic wave radiation generated by microprocessors may 
adversely affect the SD Video Camera, disturbing the pictures and sound.
  •  If the SD Video Camera is adversely affected by electromagnetic equipment 
and stops functioning properly, turn the SD Video Camera off and remove 
the battery or disconnect AC adaptor.
Then reinsert the battery or reconnect AC adaptor and turn the SD Video 
Camera on.
●  Do not use the SD Video Camera near radio transmitters or high-voltage 
lines.
  •  If you record near radio transmitters or high-voltage lines, the recorded 
pictures and sound may be adversely affected.
●  Use the cord or cable supplied with the unit or other devices. Do not extend 
the cords and the cables.
●  Do not expose the unit to insecticide or volatile substances, or allow prolonged 
contact with rubber or vinyl products. (This can cause deformation and 
peeling.)
●  Do not drop or impact the unit while carrying.
  •  Strong impacts may damage the outer casing, causing it to malfunction.
●  Do not use the unit for business purposes such as surveillance. 
  •  This unit is not of professional grade, and can build up heat internally over 
extended use, resulting in trouble.
●  Before long periods of disuse:
  •  Wipe away moisture and dirt with a soft dry cloth, dry naturally and store with 
desiccant (silica gel).
Others5Cautions for use 
						

							97VQT1R00
SD cards
●  The memory capacity indicated on the SD card label is the total of the 
capacity for copyright protection and management, and that ordinarily used by 
the unit, computers, etc.
●  MiniSD cards require a purpose-specific adaptor. Do not insert just the miniSD 
card or just the adaptor. Also, do not insert and remove a miniSD card while 
keeping the adaptor inserted into the unit. (This can cause damage.)
Battery
●  The rechargeable lithium ion battery used with this unit is readily affected by 
temperature and humidity. In cold places, the full battery indication may not 
appear and a low battery warning may appear approx. 5 minutes after starting 
use. In high temperatures, a protective function may be triggered, preventing 
use.
●  After use, always remove and store the battery.
  •  If left inside the unit, the battery may over-discharge because of small 
amounts of current flow, ultimately damaging the battery. 
  •  Place the battery in a plastic bag so as to prevent metal from contacting 
terminals and store in a cool (15 - 25 ˚C (59 - 77 ˚F) dry (40 - 60 % RH) 
place subject to minimal temperature changes. 
  •  Storing the battery in extreme cold or high heat may shorten the battery’s 
service-life. Moreover, places that are hot, humid or oily can rust terminals 
and cause damage to the battery.
  •  During long-term storage, charge the battery once a year, then use it until 
depleted and store it again. 
  •  Clean battery terminals of adhering dust, etc.
●  Bring a spare battery with you when going out.
  •  Bring 3 - 4x more battery power than you plan to use. In cold places such as 
ski resorts, recording time becomes shorter.
  •  Do not forget the AC adaptor when traveling so that you can recharge 
batteries.
●  Do not use batteries if damaged or deformed (especially terminals) from 
dropping, etc. 
  •  This can cause damage to the unit.
●  Do not throw batteries into fire.
  •  The battery may burst if heated or thrown into fire.
●  If the battery does not last long immediately after charging, it has reached the 
end of its service-life. Purchase a new battery. 
						

							98VQT1R00
AC adaptor
●  Use the supplied AC adaptor.
●  If the battery itself is too hot or too cold, it may take time to charge or may not 
charge at all.
●  Keep the AC adaptor at least 1 m (3.3 feet) away from the radio. (Interference 
may affect the radio.)
●  During use, the AC adaptor may make noises internally; however, this is 
normal.
●  After use, unplug the AC adaptor from its AC outlet. (Leaving it connected 
consumes 0.3 W [max.] of power.)
●  Keep the terminals of the AC adaptor clean.
Keep the AC adaptor near an AC outlet and yourself within arm’s reach of 
a breaker (AC plug).
LCD monitor
●  If the LCD monitor fogs up or becomes dirty, wipe it clean with a soft dry cloth.
●  When the unit is extremely cold in cold places or in other such conditions, 
although the LCD monitor may be slightly dark immediately after turning 
power on, the normal brightness is restored when internal temperature rises.
The LCD monitor is made with high-precision technology; however, black 
spots may appear in displays or stuck lighting (red, blue or green) may occur. 
There is nothing wrong with the monitor.
The LCD monitor pixels are controlled to a 99.99 % degree of accuracy; 
however, dead or stuck pixels may occur in the remaining 0.01 %. These pixel 
defects are not recorded in SD card images, therefore do not worry.
Others5Cautions for use (cont.)  
						

							99VQT1R00
Condensation
●  If condensation adheres to the unit, the lens may fog and the unit and SD card 
may not function properly. Avoid sharp changes in temperature and humidity.
●  Condensation may adhere in the following cases:
  •  After summer rain showers or in humid places where the air is thick with 
steam
  •  When heaters are turned on in cold rooms
  •  When moving from cold places to warm places
  •  When the unit is directly exposed to cold drafts (i.e., air conditioners, etc.) 
●  In the event of differences in temperature or humidity, place the unit in a 
plastic bag, remove as much air as possible, seal and let it sit for about 1 hour 
to adjust to the ambient temperature.
●  If the lens fogs up, remove the battery and disconnect the AC adaptor, open 
the card/battery door and let it sit for about 1 hour to adjust to the ambient 
temperature.
Cleaning
●  Remove the battery and disconnect the AC adaptor.
●  Do not use benzene, thinner, alcohol, etc. (These substances can cause 
deformation and peeling.)
●  Wipe off fingerprints and dust with a soft dry cloth. For stubborn dirt, soak a 
cloth in water, wring it out well, and use it to wipe the dirty surfaces. Then wipe 
the surfaces with a dry cloth.
●  Use chemically impregnated tissues in accordance with warnings and 
indications. 
						

							100VQT1R00
Others6Specifications
SD Video Camera : Information for your safety
Power source:DC 5.0 V (When using AC adaptor), DC 3.6 V (When using battery)
Power consumption:Recording: 2.9 W, Charging: 4.5 W
Signal systemEIA Standard: 525 lines, 60 fields NTSC color signal
Image sensor1/6˝ CCD image sensor
Total: 680 K
Effective pixels:
    Moving picture: 340 K (4:3), 300 K (16:9)
    Still picture: 350 K (4:3)
LensAuto Iris, F1.8 to F2.4
Focal length: 2.3 mm to 23.0 mm
Macro (Full range AF)
Zoom10x optical zoom, 25/700x digital zoom
Monitor2.7˝ wide LCD monitor (approx. 123 K pixels)
MicrophoneStereo (with a zoom function)
Speaker1 round speaker
White balance adjustmentAuto tracking white balance system
Standard illumination1,400 lx
Minimum required illuminationApprox. 6 lx (Low light mode, 1/30)
[Approx. 2 lx with the MagicPix function]
Video output level1.0 Vp-p, 75 Ω
Audio output level316 mV, 600 Ω
USBCard reader/writer function (No copyright protection 
support) Hi-Speed USB (USB 2.0), USB terminal 
Type miniAB, PictBridge-compliant
Dimensions 
(excluding the projecting parts)41.0 mm (W) x 59.0 mm (H) x 102.0 mm (D)
[1.60˝ (W) x 2.30˝ (H) x 4.00˝ (D)]
Mass (Weight)Approx. 160 g (0.35 lbs.)
without an SD card and supplied battery
Mass (Weight) in operationApprox. 182 g (0.40 lbs.)
with an SD card and supplied battery
Operating temperature0 °C to 40 °C (32 °F to 104 °F)
Operating humidity10 % to 80 %
Battery operation timeRefer to page 22.