Panasonic Sdr S100 Operating Instructions Manual

11VQT0T50
26 LCD monitor (P21, 107) 
27 Power LCD button [POWER LCD] (P30)
28 Reset button [RESET] (P101)
29 Card access lamp [ACCESS] (P15)
30 Card slot open lever (P14)
31 Card slot cover (P14)
32 Strap fixture (P12)
Lens hood
1In order to remove the lens 
hood, rotate it 
counter-clockwise. 
2In order to fit it, put into slot A, 
and then rotate it clockwise.
Tripod mount
This is a hole for attaching this unit to a tripod 
(optional). (Please carefully read the operating 
instructions for how to...

12VQT0T50
Multi-connector [MULTI]
Only connect the supplied multi cable and supplied headphone cable to this connector 
as the sound may not be output correctly if you connect other cords. 
∫Connecting headphones 1 (optional:‰ 3.5 mm stereo mini plug) 
using the headphone cable (supplied) 2
Hand strap fixture
We recommend using the hand 
strap (supplied) to prevent the unit 
from dropping.
1
 Hand strap
Remote control
1 On-screen display button [OSD] (P71)
2 Date/time button [DATE/TIME] (P29)
3 Menu...

13VQT0T50
∫Install a button-type battery (supplied) in the remote control
1) While pressing the stopper 1, pull out 
the battery holder.
2) Set the button-type battery with its (i) 
mark facing upward 2 and get the 
battery holder back in place.
∫About the button-type battery
≥When the button-type battery runs down, replace it with a new battery (CR2025). 
The battery typically lasts about one year; the actual life may be less with heavy use.
≥Keep the button-type battery out of the reach of children....

14VQT0T50
Before inserting/removing an SD card, be sure to turn the power [OFF]. (P18)
If the SD card is inserted or removed with the power turned on, this unit may 
malfunction or the data recorded on the SD card may be lost.
1Open the LCD monitor and then slide 
the card slot open lever 1 to open the 
card slot cover.
2Insert/remove the SD card into/from 
the card slot 2.
ALabel side
≥When inserting an SD card, face the label side 
towards you and press it straight in with one 
stroke as far as it...

15VQT0T50
∫About the SD Memory Cards that you can use
¢The recording may suddenly stop during motion picture recording. (P35)
∫About the SD card
≥Do not touch the terminals on the back of the SD card.
≥Electrical noise, static electricity, or failure of this unit or the SD card may damage or 
erase the data stored on the SD card. We recommend saving important data on a 
PC by using the USB cable (supplied) or MotionSD STUDIO. (P73) (When saving 
images recorded using this unit to a PC, you must use...

16VQT0T50
1Remove the battery cover.
1While pushing the battery cover,
2 slide it in the direction of the arrow.
2Insert the battery.
1Place the battery label side up.
2 Insert the projecting parts of the battery 
in the holes on the unit.
3 Put the battery cover back in its 
original place.
A Label
B Projecting parts
Removing the battery
Remove the battery cover, then 
remove the battery.
≥After removing the battery, put the battery 
cover back in its original place.
Inserting/Removing the Battery
1 1...

17VQT0T50
When this unit is purchased, the battery is not charged. Charge the battery before using this unit.
¬Set the power switch to [OFF]. (P18)
Connect the AC adaptor (supplied) A 
to this unit and the AC outlet.
1Open this unit’s terminal cover.
2Connect the AC adaptor to this unit’s DC 
input terminal [DC IN 9.3V].
3Connect the AC mains lead to the AC 
adaptor, then the AC outlet.
The status indicator B starts blinking in red at 
intervals of about 2 seconds to signal that 
charging has commenced....

18VQT0T50
How to turn on the power
Set the power switch to [ON].The status indicator 1 lights red and, in motion 
picture recording mode or still picture recording 
mode (P20), the lens cover opens.
How to turn off the power
Set the power switch to [OFF].The status indicator goes out and the lens cover 
closes.
≥If the LCD monitor is closed in motion picture 
recording mode or still picture recording mode 
(P20), the power turns off.
Quick start
If quick start is set and then the LCD monitor is closed...

19VQT0T50
To cancel quick start
Press the menu button, use the cursor button to select [ SETUP]# 
[ QUICK START]#[OFF]. (P26)
≥To cancel quick start standby, turn off the 
power.
≥Quick start standby is canceled after 
5 minutes have elapsed. 
In this case, the unit cannot be 
quick-started and it takes longer for it to 
start operating.
≥Quick start standby is canceled if the 
mode dial is switched to a mode other 
than motion picture recording mode or 
still picture recording mode.
≥Since about half...

20VQT0T50
The Mode Dial is used to switch between recording and playback modes.
Rotate the mode dial slowly but surely.
Set the desired mode 1.
Rotate the mode dial, and set the 
desired mode pictograph to the 
position shown in the illustration.
Motion picture 
recording mode 
(P33)
Use this to record 
motion pictures 
(MPEG2).
The unit can be used as a Web camera when 
it is connected to a PC.
Motion picture 
playback mode 
(P57)
Use this to play back 
motion pictures 
recorded with this 
unit.
Still...