Panasonic Sc Htb70 Owners Manual

Getting started
RQT976311
Precautions
[HTB70]
Attach the stands if necessary. If not, proceed to step 3.
Place the main unit in the desired position and attach each cord onto the 
rack or table.
≥Make sure that the slack of the cord is minimal.
[A]: With basic stands[B]: With 30o stands[C]: With 80o stands
AScrew (supplied)≥Tighten securely.
BScrew eye≥Attach at a position capable of supporting over 33 kg (72.8 lbs).
≥Depending on the placement of the main unit, the screwing position of the screw eye may...

12RQT9763
This unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the screw 
used and the wall are strong enough to support the weight of at least 33 kg (72.8 lbs).
The screws and other items are not supplied as the type and size will vary with each installation.
≥Refer to step 2 for details about the required screws.
≥Be sure to attach the fall prevention cord as a secondary safety measure.
Supplied accessories
Additionally required accessories (commercially available)...

Getting started
RQT976313
Precautions
Attach the wall mount brackets to the wall.
Complete all the necessary connections to the main unit. (>15 to 17)
≥Connect the AC power supply cord to the main unit, but do not connect it to the household AC outlet until the installation is 
completed.
Attach the cord to the main unit.
AWall mount bracket (supplied)
BScrewsCAt least 30 mm (13/16q)
D‰4.0 mm (5/32q)
E‰7.5 mm to ‰9.4 mm (19/64q to 3/8q)
FWall
GWall mount bracket (supplied)
HCord
§
§ If the cord cannot be...

14RQT9763
Attach the main unit to the wall mount brackets.
Screw the safety holder onto the wall mount brackets.
≥Screw tightening torque: 80 N0cm (0.6 lbf0ft) to 120 N0cm (0.9 lbf0ft).
≥The safety holders are designed to prevent the main unit from falling off the wall mount bracket.
Secure the cord to the wall.
≥Make sure that the slack of the cord is minimal.
AWall mount bracket (supplied)
BGently move the main unit down onto the wall mount bracket.
CScrew without washer (supplied)
DSafety holder...

Getting started
RQT976315
Precautions
Step 3  Connections
≥Turn off all equipment before connection and read the appropriate operating instructions.
Do not connect the AC power supply cord until all other connections are completed.
Connection with the TV
AOptical digital audio cable≥When you use the optical digital audio cable, insert the tip correctly into the terminal.
Connection with other device
BAudio cable

OPTICAL
    OUT
O P T I C A L DIGITAL 
AUDIO IN (TV)

L
R 
AUDIO OUT
AUDIO INBD/DVD
e.g.,...

16RQT9763
With the IR Blaster connection, it is possible to send the IR signal received by this system’s remote 
control signal sensor to the TV’s sensor.
Use the TV’s remote control within the operation range of this system’s remote control signal 
sensor.
≥For the operation range, refer to page 7.
Connect the jack plug to the main unit’s Ir SYSTEM terminal.
Place the infrared emitter in sight of the TV’s remote control signal 
sensor.
≥For the location of the TV’s remote control signal sensor, refer to...

Getting started
RQT976317
≥Connect only after all other connections are completed.
≥This system consumes a small amount of AC power (>25) even when it is turned off. In the interest of 
power conservation, if you will not be using this system for a long time, unplug it from the household 
AC outlet.
By using the Bluetooth
® connection, you can listen 
to the sound from the Bluetooth® audio device 
from this system wirelessly.
Preparation≥Turn on the Bluetooth® feature of the device and 
place the device...

18RQT9763
0QFSBUJPOTUsing this system
Preparation≥Turn on the TV and/or connected device.
Press [Í] to turn on the main unit.
Select the source.
≥This remote control cannot be used to control the operations 
of the connected devices.
∫When “ ” is selected as the source
On the Bluetooth® device:Select this system as the output source of the connected 
Bluetooth® device and start the playback.
∫When “BD/DVD” is selected as the 
source
On the TV and the connected device:Select the TV’s input for the device...

Operations
RQT976319
3D sound
This system provides a feeling that the sound and the 
image are as one.
≥To change the applied effect, refer to “Sound modes”. 
(>right)
	≥To turn off Dolby Virtual Speaker and the 3D surround 
effects, select “STEREO” as the sound mode. (>right)
≥To turn off the 3D surround and the Clear-mode dialog 
effects, refer to “Using the Dolby Virtual Speaker effect”. 
(>21)
By changing the sound mode, it is possible to enjoy the 
sound that is suitable according to the TV program...

20RQT9763
Advanced operations
To display the current audio format.
Press and hold [SOUND] for more than 
4 sec.
≥The current audio format is indicated for 5 sec.
	Audio format is not indicated when “” or “BD/DVD” is 
selected as the source.
Change the dual audio from main to secondary.
≥This setting will only work if the audio output setting on 
the connected TV or player, etc. is set to Bitstream 
and dual audio is available in the audio source.
Press and hold [MUTE] for more than 
4 sec.
While the...