Panasonic Rp Wh5000 Operating Instructions Manual

RP-WH5000
ENGLISH ESPAÑOLPORTUGUÊS
Digital Cordless Surround Headphones
Auriculares inalámbricos digitales de
sonido ambiental
Auscultadores Surround Digital Sem Fio 
Operating Instructions
Instrucciones de funcionamiento
Manual de instruções
Before connecting, operating or adjusting this
product, please read the instructions completely.
Please keep this manual for future reference.
Antes de conectar, operar o ajustar este producto,
sírvase leer estas instrucciones completamente.
Guarde este manual....

3 23RQT8164ENGLISH
2RQT8164
Table of contentsIMPORTANT SAFETY INSTRUCTIONS
....3
Features...................................................4
Precautions .............................................4
Listening caution ....................................5
Control reference guide .........................5
Power Supply Preparations : Headphones
..............................................................7Using the rechargeable batteries (supplied)
.....7
Using dry cell batteries (not included)...

5 45RQT8164ENGLISH
4RQT8164
Control reference guideTransmitter’s front panel
Infra-red signal transmission window
Place the transmitter where the  infra-red signal
transmission window can be seen with no
obstruction.
POWER/CHARGE lamp ( page 8)
• It glows green when infra-red rays are being
emitted.
• It turns red when the headphones are being
charged.
• It goes out when charging is complete or infra-
red rays stop being emitted.DECODE MODE lamp ( pages 12-13)
(DOLBY DIGITAL, DOLBY PRO LOGIC ,
DTS,...

77RQT8164
Power Supply Preparations : Headphones
ENGLISH
6RQT8164
Control reference guide
6
Transmitter’s rear panelHeadphones
ATT
L
LINE INDIGITAL INR0 dB
-8 dBOPTDC IN    6V
ATT control ( page 11)
Switch to [0 dB] when sound from an analog
input is low. The standard setting is [-8 dB].LINE IN terminal ( page 10)
To connect to the audio out terminals of AV
equipment such as a video cassette recorder or
television (sold separately).DIGITAL IN terminal ( page 9)
To connect to digital equipment such as a...

99RQT8164ENGLISH
8RQT8164
Power Supply Preparations : Headphones
8
2
Put the headphones on the transmitter
making sure that the charging terminals
are in contact with each other.• The POWER/CHARGE lamp on the transmitter
glows red.
• The lamp goes out when the batteries are fully
charged. It takes approximately 16 hours to
charge the supplied batteries.
• When putting the headphones on the
transmitter, hold the left and right housings in
each hand and put the headphones straight
down onto the...

1111RQT8164ENGLISH
10RQT8164
Connections
10
25 mm
Using an optical digital cable• Do not let falling objects subject the optical digital cable to
vibration or shock.
• Hold the plugs in your hands and carefully connect or
disconnect the optical digital cable.
• If the ends of the optical digital cable become dirty or dusty,
efficiency will decrease.
Keep them clean.
• For safety reasons, attach plug caps and do not bend the
optical digital cable too much.Sound types• A DTS compatible DVD player is...

1313RQT8164ENGLISH
12RQT8164
Using the transmitter and headphones
12
Before using the transmitter, read [Connections]( pages 9-11) and ensure that it is connected
correctly.
1
Turn on the equipment connected to the
transmitter.
3
Take the headphones off the transmitter.The transmitter’s power automatically turns on
and the infra-red signal transmission window
lights. The DECODE MODE lamp and
SURROUND lamp will light approximately 5
seconds later to indicate the audio signal being
input from the connected...

15 1415RQT8164
Selecting the surround field
ENGLISH
Using the transmitter and headphones
14RQT8164
When you remove the headphones,
the power turns off automatically
(Auto power on/off function). Do not pull up the free-adjusting band when not
using the headphones. This may cause the auto
power on/off function to switch the headphones
back on and battery power to run down.If no audio signal is received at the transmitter for more than 5 minutes
(approximately)The infra-red rays being emitted from the...

1717RQT8164ENGLISH
16RQT8164
Troubleshooting guide
16
Before requesting service, make the below checks. If you are in doubt about some of the check points,
or if the remedies indicated in the chart do not solve the problem, refer to the “Product information” onpage 19.Take both the headphones and the transmitter when you visit your dealer.Problem
No sound.
Sound is lowPossible cause and suggested remedy
Check that the transmitter and the AV equipment are connected 
( pages 9-11).Turn on the AV equipment...

19 18
ENGLISH19RQT8164
18RQT8164
Product service
Problem
The DOLBY PRO
LOGIC II lamp does
not light.The DOLBY PRO
LOGIC II lamp lightsThe DTS lamp
does not light.Cannot chargeInfra-red 
ray output does not
stop.Possible cause and suggested remedy
You have set the transmitter’s SURROUND button to “OFF” ( page
13).There are no analog input signals, digital input signals (PCM) or Dolby
Digital 2-channel signals being input.There are analog input signals, digital input signals (PCM) or Dolby Digital...