Panasonic Pv L452 Operating Instructions Manual

							11
Getting Started
Cassette Information
1Turn Tape Wheel in direction of arrow
until there is no slack.
2Attach Battery (page 9).
3Slide TAPE EJECT to open door.
4Insert cassette as shown.
5Press here to close door.
1
2
3
4 To remove the cassette, slide the TAPEEJECT switch.5
1To prevent accidental erasing,break off tab with screwdriver.
(Or, slide tab open.)
2To record again,cover hole with adhesive tape.
(Or, slide tab closed.)
Protects tapes from being accidentally
erased.
Erase Protection Tab
Cassette Insertion/Removal
Slide tab type
12
 SLP playback may contain more picture noise.SLP
(Super Long Play)
SP
(Standard Play)
Cassette type
Tape Speed
Selector Position
TC-20
20 minutes
1 hour30 minutesTC-30 TC-40
40 minutes
1 hour
30 minutes2 hours
Use tapes with the  mark in this unit.
Record/Playback Time 
						

							12For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before Using
Remove Battery Pack before doing steps.
1Undo strap ends
from buckles.
Attaching Shoulder StrapAdjust the Length of the
Shoulder Strap
Pull a loop of strap from buckle, then pull
strap tight to shorten or lengthen.
Adjust Hand Strap length to fit your hand as
shown.
2Thread strap ends through Strap
Rings on Camcorder.
3Re-insert the strap
ends into buckles.
Hand Strap
123
min. 25.4 mm (1 inch)
Attaching the Lens Cap
Strap:
Thread the Strap through
the Lens Cap attachment
ring as illustrated at left.
Lens Cap
Attaching the Lens Cap Cord to the Hand Strap:
Remove the Hand Strap from the front clasp and thread
the Strap through the loop in the Lens Cap Cord.
Reattach the Hand Strap.
How to remove the Sensor tag (PV-L452 only)
Hand Strap
Sensor tag
1Open the Hand Strap as illustrated
at left.
2Remove the Sensor tag.
Then, replace the Hand Strap. 
						

							13
Getting Started
Using MENU Mode
Before you begin...
 Connect Camcorder to power source.
 Set POWER to CAMERA or VCR.
1Press MENU for MENU mode.
The CAMERA or VCR MENU screen (see below
left) appears when Menu mode is entered.
2Press UP or DOWN to highlight the
desired menu item.
3Press DISPLAY to set selection.
4Press MENU to exit.
Note:
 The Menu mode is canceled if 
UP/DOWN,DISPLAY, or MENU are not pressed within 5
minutes when Self Demo mode is off.
 The Menu mode is canceled if 
UP/DOWN,DISPLAY, or MENU are not pressed within 30
seconds when Self Demo mode is on.
1
2
3
4
5
6
7
8
9
10
11
MENU Mode (VCR) Screen
MENU Mode (CAMERA) Screen1PROGRAMMED REC (page 19).
Camcorder starts and stops recording at a
preset time.
2DISPLAY (page 46).
ON : On-screen Display (OSD) screens are
displayed.
3SHUTTER (page 26).
Select desired shutter speed.
4STAND-BY RELEASE (page 18).
ON : Enables quick resumption of recording
from Stand-by mode.
5CLOCK SET (pages 14, 15).
Select to set clock.
6LIGHT MODE (page 16).
ON/OFF : Light can be set ON or OFF.
ON/OFF/AUTO : Light can be set ON, OFF, or AUTO.
7SELF DEMO (page 7).
ON : SELF DEMO screen is displayed.
8DIGITAL WIPE (pages 39, 40).
ON : Digital wipe mode can be used.
9MAGICPIX (page 24).
ON : Picture sensitivity is increased.
10MOTIONSENSOR (page 33).
ON : Enables MotionSensor recording.
11VIDEO EFFECTS (pages 27~29).
AUTO FADE : BLACK or WHITE
DIGITAL FADE : TYPE
7 types
COLOR8 colors
DIGITAL FILTER : COLOR5 colors
 5
 2
1, 2, 3, 4 
						

							14For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Setting the Clock
Before you begin...
 Connect Camcorder to power source.
 Set POWER to CAMERA or VCR.
Set the following items in order: Time
Zone, Daylight Saving Time, Date,
and Time.
1Press MENU for MENU mode.
Press 
UP or DOWN to select CLOCK SET .
2Press DISPLAY for
CLOCK SET menu.
Press 
UP or DOWN to
select TIME ZONE, DST,
or DATE/TIME.
3Press DISPLAY for menu of item selected in
step 2.
To change the setting:
TIME ZONE➔Go to step 3a on page 15.
D.S.T.➔Go to step 3b on page 15.
DATE/TIME➔Go to step 3c on page 15.
4Press MENU twice to exit.
[ VCR  MODE ] [ CAMERA  MODE ]
1, 2, 3, 4 
						

							15
Getting Started
Date and time including leap year are
calculated up to DEC 31, 2099.
Spring (First Sunday in April) :
ahead one hour.
Autumn (Last Sunday in October) :
back one hour. Clock will auto-adjust to daylight saving time (DST).
ATLANTICATLANTIC
EASTERNEASTERNCENTRALCENTRAL
MOUNTAINMOUNTAIN
PACIFICPACIFIC
ALASKAALASKA
HAWAIIHAWAIISAMOASAMOA
11:00
10:00 7:00 8:00 9:00 2:0012:00
6:00 1:00
Setting the Time Zone
When traveling, repeat this operation and
select one of the 8 listed time zones to
set the clock to local time.
Press 
UP or DOWN to
select OFF or AUTO.
Press 
DISPLAY to
confirm entry. Press 
UP or DOWN to
select local time zone.
Press 
DISPLAY to
confirm entry.
DST: AUTO
Press or hold down 
UP orDOWN to select hour, then
press DISPLAY to fix.
Repeat for minute, month, day,
and year.
Clock starts when year is
entered and 
DISPLAY is
pressed.
EXAMPLE :
Note:
Auto DST does not function if time zone
is set to Hawaii or Samoa (see “Setting
the Time Zone” above). Note :
Clock may lose or gain up to 2 minutes
per month.
 When traveling outside the listed time
zones, set clock to local time manually.
 To adjust or set clock, see “Setting Date
and Time” bottom of page.
The Camcorder is preset to DST: AUTO .
If DST is not observed in your area, set
to OFF by doing the following.
[ Time Zone chart ]
The Camcorder is preset to Eastern time.
Auto Daylight Saving Time
Setting Date and Time
Setting the Clock
3a
3b
3c 
						

							16For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Note:
• Using Light reduces battery operating time.
• Provide proper ventilation when using
Light extensively in a hot environment.
• Using Light when the Camcorder is
powered by a car battery may shorten
bulb life.
• Set Light to OFF when not in use.For recording in dim lighting.
Using the Light
Built-in Auto Light
1, 2, 3
CAUTION:
Light becomes hot.
Never cover Light while on.
LIGHT
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
A
EVF or LCD Monitor
A : Light is on.
A : Light mode is auto.
1Press MENU for
MENU mode. Press
UP or DOWN to
select  LIGHT MODE .
2Press DISPLAY to set OFF/ON or
OFF/ON/AUTO. Press MENU to exit.
3Press LIGHT repeatedly for Light ON,
OFF, or AUTO.
• In AUTO, light turns itself on/off
according to lighting conditions.
Replacing the BulbBefore you begin...• Order Part No. VLLW0015 for replacement
bulb.
• Set POWER to OFF.
1
2
3
DANGER:
Use only replacement bulb (PART NO. VLLW0015) supplied by Panasonic to reduce risk
of fire.
Handle new bulb with cloth or tissue as skin oils will decrease bulb life.
Remove lens cover and allow bulb to cool before replacing to avoid possible burn hazard.
1Slightly raise portion  A  of lens cover
to unhook, and slide portion  B
forward to remove.
2Using Tweezers or needle-nose pliers,
carefully remove bulb.
•Take unit to service center if you need
assistance.
3Replace bulb using a clean cloth or
tissue. (Do not touch with fingers.)
4Replace lens cover.
Note:
• Handle bulb gently. Excessive force may
cause bulb to crack.
B
A 
						

							17
Basic Operation
Camera Recording
Before you begin...
 Connect Camcorder to power source.
 Insert cassette with record tab (page 11).
View recording scene on EVF (Electronic
Viewer Finder) or LCD (Liquid Crystal
Display) monitor.
Recording via EVF or LCD
Monitor
1Press LCD-OPEN to unlock the LCD
monitor. Swing LCD monitor fully open
and adjust viewing angle.
 If you want to record using EVF, close
and lock LCD monitor.
2Set POWER toCAMERA.
 Be sure POWER
is fully turned to
CAMERA position.
 EVF or LCD monitor
turns on/off by the POWER switch.
 EVF shuts off when LCD monitor is
opened and turns back on when LCD is
closed (Color EVF model only).
 Both EVF and LCD monitor turn on
when LCD is at 180° (see above left).
This allows both you and the subject to
view the recording.
3LCD : Press BRIGHT
ADJUSTMENT
to adjust LCD
monitor
brightness level.
EVF : Look into EVF and adjust
VISION ADJUSTMENT to your
eyesight.
4Hold down TAPE SPEED for about 1
second to change tape speed to SP/SLP
(page 11).
5Press RECORD/PAUSE to start or
pause recording.
6Set POWER to
OFF when finished.
 To remove the cassette, slide the
TAPE EJECT switch (page 11). Note:
 When Camcorder is aimed at excessively bright
objects, or bright lights, a vertical bar may
appear in the picture. This is normal for the
CCD pick-up. Try to avoid this when possible.
 Using LCD monitor reduces battery operation
time. Return LCD monitor to locked position
when not in use.
EVF or LCD Monitor
(Record/Pause mode)
EVF or LCD Monitor
(Record mode)
Tape speed
WARNING (PV-L652 only) : Do not leave the camcorder with the EVF
aimed directly at the sun. This may cause
damage to the internal parts of the EVF.
1
3
BRIGHT
ADJUSTMENT
CAUTION :Rotating partially open LCD
monitor may block cassette door
and damage Camcorder body.
VISION
ADJUSTMENT
3
4
Built-in
Microphone
2, 6
5 
						

							18For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before you begin... Connect Camcorder to power source.
 Insert cassette with record tab (page 11).
Camera Recording
1Set POWER to
CAMERA.
2Press MENU for
MENU mode.
Press 
UP or DOWN
to select STAND-BY RELEASE .
3Press DISPLAY to select ON/OFF.
ON :From Stand-by mode, press
RECORD/PAUSE two times to
resume recording.
OFF :From Stand-by mode, set
POWER to OFF, then to
CAMERA. Press RECORD/PAUSE to record.
4Press MENU to exit.
Stand-by Quick Release
If left in RECORD/PAUSE mode for 5
minutes, Camcorder switches to Stand-by
mode to conserve battery. When set to ON,
Stand-by Quick Release lets you resume
recording by pressing 
RECORD/PAUSE two
times. Stand-by Quick Release is set to OFF
at the factory.
aPress RECORD/PAUSE to stop
recording.
bSet POWER to OFF and leave cassette
in Camcorder.
cTo resume recording, set POWER to
CAMERA.
dPress RECORD/PAUSE to resume
recording.
Note:
 Use Manual Easy Edit (left) if more than 24
hours before recording is resumed.
Manual Easy Editing
For a smooth transition between scenes if
recording is stopped, and then started within
24 hours. For proper continuity when taping from
Stop mode or after attaching a new
Battery.
Easy Edit Stand-by
ASet POWER to VCR.
BaPress REWIND/SEARCH to rewind
a few seconds of tape.
bPress 
PLAY to review recording.
cPress 
STILL where you want to
continue recording.
CSet POWER to CAMERA.
DPress RECORD/PAUSE to resume
recording.
2, 3, 4B
b
1, b, c,
A, Ca, d, D
ac 
						

							19
Basic Operation
Before you begin...
 Connect Camcorder to power source.
Use AC Adaptor for longer recordings.
 Insert cassette with record tab (page 11).
 Set POWER to CAMERA.
Camera Recording
1Press MENU for MENU
mode. Press 
UP or
DOWN to select
PROGRAMMED REC .
2Press DISPLAY.
(Current time is
displayed.)
Each additional press
of 
DISPLAY increases
start time by 30 minutes.
3Press DOWN to select
REC TIME .
Press 
DISPLAY
repeatedly to select one
of the options shown at
left.
To cancel the setup, press 
MENU twice.
4Press RECORD/PAUSE
to place Camcorder in
stand-by mode.
Recording will be done as scheduled.
Note:
 Start time may not be set over 24 hours from
current time.
 Camcorder shuts off at tape end, or 12 hours
after Interval Recording starts.
 To cancel, set 
POWER to OFF.
Set a recording start and stop time. Or,
set a 5 or 10 second interval recording
to be done each minute.
*1Record 5 seconds each minute.
*2Record 10 seconds each minute.
REC TIME :
Programmed Recording
4
1, 2, 3 
						

							20For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Playing Back Recordings
Before you begin...
 Connect Camcorder to power source.
 Insert recorded tape.
Tracking Control
Quick Visual Search
Search Speed SP   (Standard Play)     : 3 times normal.
 SLP (Super Long Play) : 9 times normal.
During playback, press:FF     : fast forward search
REW : rewind search
Press again or press PLAY for normal play.
Still Picture
Press STILL to freeze picture.
Press again for normal play.
This feature works best in SLP mode (page 11).
Special Effects
Note: During search, horizontal noise bars will appear.
Audio is muted.
 To protect video heads and tape, operating
modes will revert as follows after 5 minutes:
Still Stand-by
Stand-by Power off (when Battery Pack is
used).
 Tape auto-rewinds if played or fast forwarded to end.
Note: Using LCD monitor reduces battery operating
time. Return LCD monitor to locked position
when not in use.
1Press LCD-OPEN and swing LCD
monitor fully open.
 If you want to playback on EVF, close
and lock LCD monitor.
2Set POWER to VCR.
 If tape has no record tab, auto
playback begins.
 EVF or LCD monitor turns on/off by
the POWER switch.
 EVF shuts off when LCD monitor is
opened and turns back on when LCD
is closed (Color EVF model only).
3Playback function buttons.
AREW: Rewind tape.
BPLAY: Play tape.
CSTOP: Stop tape.
DBRIGHT:Adjust LCD monitor brightness.EVOLUME: During playback, adjust
volume of speaker.
Press “T” : Volume
up (+).
Press “W” : Volume
down (-).
Playback on EVF or LCD Monitor
Auto Tracking
Continuously analyzes each recording for
optimum picture quality.
Manual Tracking
Some recordings require manual
adjustment to reduce noise.
Press 
UP or DOWN until Playback picture
clears up.
Press 
DISPLAY to return to Auto Tracking.
Speaker
1
3BRIGHT
ADJUSTMENT
D
2
3
B
A
C
E
STILL