Panasonic Pv Dv73 Operating Instructions Manual

41
Digital Features
Digital Features
EIS ON NORMAL
1Set POWER to CAMERA.
2Press EIS to stabilize the picture.
 Picture flicker may be observed when
taping under fluorescent lighting
conditions.
 The EIS indicator flashes when the
light level is inadequate.
 Turn D.E.I.S. OFF during recording
when using a tripod.
3Press REC/PAUSE to start recording.
4Press EIS again to cancel.
 Be sure that D.E.I.S. is turned off
when not needed.
Dual Digital Electronic Image
Stabilization System (D.E.I.S.)
This...

42For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Digital Features
Other Digital Functions
Use the following features to add interest
and professionalism to your recordings or
playback. Select from twelve special
effects.
Note
Types of Digital Functions
MIRROR
Symmetrical image from the current
camera picture.
STROBE
The recording appears as a sequence of
still frames.
MOSAIC
The picture appears in a mosaic pattern.
SLIM
The picture is expanded...

43
Digital Features
Digital Features
3, 4JOG
         KEY
1POWER
Picture in Picture (PinP)
You can display a PinP (still image) screen
on the Main Picture.
 PinP position is fixed at the bottom right
of the screen.
Note
1Set POWER to CAMERA.
2Press MENU to display the CAMERA
FUNCTIONS menu screen.
3Rotate JOG KEY repeatedly to select
 DIGITAL EFFECT , then press JOG
KEY to display the DIGITAL EFFECT
menu screen.
4Press JOG KEY to select P-IN-P .
Press MENU to exit this menu.
 “PinP” will appear in the...

44For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
External Microphone
with M3 connector (not
supplied)
External
Microphone Jack The original sound can be replaced with
new sound using the built-in Palmcorder
microphone or an external microphone.
Audio Dubbing using the
External or Built-in
Microphone
1Set POWER to VCR.
 With the Remote Control, you can set
the Palmcorder to stop automatically
at a specific point on the tape. See...

45
Editing Features
Editing Features
4Press  (PAUSE) to start Audio
Dubbing. “A.DUB ” indication
appears.
 Connect the Palmcorder to the TV in
order to monitor the sound.
(p. 38)
Only NTSC (National Television Standards
Committee) recorded tapes can be audio
dubbed. The following screen appears if
the tape was not recorded in NTSC format.
5Press  (PAUSE) to stop Audio
Dubbing. To listen to the desired audio sound, set
the 12bit AUDIO setting of the VCR mode
MENU (Menu OSD: p. 108) as follows:
 If the...

46For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
S-Video In
VHF Connecting
Cable (not
supplied)TV
(To View)
A/V Cable
(Supplied)
To Audio InRecording:
VCR (Rear)
To S-Video In
(If there is S-Video In)
 For technical reasons, dubbing a tape
may reduce its quality.
 Press DISPLAY ON TV on the
Palmcorder Remote Control to eliminate
EVF/LCD Monitor indications.
 If the Time Code is displayed in the EVF
or LCD monitor, it cannot be...

47
Editing Features
Editing Features
3, 4
PLAY
3, 4, 5
PAUSE
3, 4PLAY
6STOP
4REC High quality digital-to-digital copying can
be accomplished if both Palmcorders
incorporate the DV Input/Output (i.LINK)
Connector (DV Interface cable (i.LINK) is
not supplied).
1Insert a pre-recorded tape into the
source (playing) Palmcorder, and set
POWER to VCR.
2Insert a blank tape with the record
tab closed into the target (recording)
Palmcorder and set POWER to VCR.
3Press  (PLAY) on the source
Palmcorder. When the...

48For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Card Features
You can record still images to a Memory Card.
1Slide the M-CARD Lock Switch to
unlock, then set POWER to M-CARD.
 The POWER lamp lights red.
 Be sure POWER is fully turned to
M-CARD position.
 “PLAY: PUSH PLAY KEY” is
displayed for 10 seconds. (p. 50)
2Press MENU to display CARD SETUP
menu, then press JOG KEY to select
 NORMAL , FINE or SUPER FINE .
 Press MENU to exit this menu....

49
Card Features
1Repeat steps 1 and 2 on page 48.
2Set POWER to VCR.
3Press  (PLAY) to start playback of
the cassette tape. And then, press
 (PAUSE) to select an image.
4Press PHOTOSHOT to record the
desired image to the Memory Card.
 When PHOTOSHOT is pressed in
PLAY or SLOW mode, the screen
goes to STILL mode.
 To playback the images of the
Memory Card, see page 50.
 When Variable Speed Search is
done (p. 34), this feature cannot be
used.
5Repeat steps 3~4 to record another
image to the Memory...

50For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
1Slide the M-CARD Lock Switch to
unlock, then set POWER to M-CARD.
 “PLAY: PUSH PLAY KEY” is
displayed for 10 seconds.
2Press  (M-PLAY) to display the Multi
playback screen.
 “PLEASE WAIT” appears on-screen.
 Rotate JOG KEY to scroll through
Multi image screen pages (6 images
per page) and select an image.
 The selected image is underlined in
green.
 Press MENU to display CARD
SETUP menu...