Panasonic Pv Dv53 Operating Instructions Manual

31
VCR
Strobe Multi Mode
1Set POWER to VCR.
2Press MENU to display the VCR
FUNCTIONS menu screen.
3Rotate JOG KEY to select PLAYBACK
 FUNCTIONS , then press JOG KEY to
display the PLAYBACK FUNCTIONS
menu screen.
4Rotate JOG KEY to select PLAYBACK
 MULTI SPEED in the PLAYBACK
FUNCTIONS menu screen.
(Menu OSD: p. 61)
5Press JOG KEY repeatedly to set
desired speed.
Press MENU to exit.
6Press  (PLAY) to start playback.
Press  (MULTI) at the point you want
to start capturing.
A succession of 9 screens will...

32For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Back of TV
Audio In Video In
Special Effect Features
To Video In
To Audio In
A/V OUT
A/V Cable
(Supplied)
1Set POWER to CAMERA or VCR.
To view what the Palmcorder is
recording or to playback a tape on your
TV.
2Turn your TV ON and set it to LINE
INPUT.
Check your TV operating instructions
for further information.
3Start playback or begin a recording.
Make sure the Palmcorder and TV are
turned off...

33
Digital Features
CAMERA mode
Zoom Out (“W”) Zoom In (“T”)
5POWER
    ZOOM
D.ZOOM
The normal optical zoom functions from
1X to 10X.
As magnification increases, resolution
significantly decreases.
Because the image is enlarged digitally,
the picture may become distorted when
higher magnification levels are used.
When the level falls below 10X, the
normal zooming function will resume.
Focus distance becomes 1.2 m (4 feet) if
the lens is in full telephoto.
1Set POWER to CAMERA.
2Press MENU to display...

34For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Digital Features
VCR mode
1Set POWER to VCR.
2Press MENU to display the VCR
FUNCTIONS menu screen.
3Rotate JOG KEY to select DIGITAL
 EFFECT , then press JOG KEY
to display the DIGITAL EFFECT
menu screen.
4Rotate JOG KEY to select D. ZOOM ,
then press JOG KEY to select ON.
Press MENU to exit.
5Press  (PLAY) to start playback.
The center portion of the image
doubles in size.
6Repeat steps 2~4 to...

35
Digital Features
Digital Features
EIS ON NORMAL
1Set POWER to CAMERA.
2Press EIS to stabilize the picture.
Picture flicker may be observed when
taping under fluorescent lighting
conditions.
The EIS indicator flashes when the
light level is inadequate.
Turn D.E.I.S. OFF during recording
when using a tripod.
3Press REC/PAUSE to start recording.
4Press EIS again to cancel.
 Be sure that D.E.I.S. is turned off
when not needed.
Dual Digital Electronic Image
Stabilization System (D.E.I.S.)
This feature...

36For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Digital Features
1Set POWER to CAMERA or VCR.
2Press MENU to display the menu
screen.
3Rotate JOG KEY to select DIGITAL
 EFFECT in the CAMERA or VCR
mode menu screen, then press JOG
KEY to display the DIGITAL EFFECT
menu screen.
4Rotate JOG KEY to select EFFECT in
the CAMERA mode menu screen or
 EFFECT1 / EFFECT2 in the VCR
mode menu screen, and then press
JOG  KEY repeatedly to select one of
the...

37
Digital Features
Digital Features
3, 4JOG
         KEY
1POWER
Picture in Picture (PinP)
You can display a PinP (still image) screen
on the Main Picture.
PinP position is fixed at the bottom right
of the screen.
Note
1Set POWER to CAMERA.
2Press MENU to display the CAMERA
FUNCTIONS menu screen.
3Rotate JOG KEY repeatedly to select
 DIGITAL EFFECT , then press JOG
KEY to display the DIGITAL EFFECT
menu screen.
4Press JOG KEY to select P-IN-P .
Press MENU to exit this menu.
“P-IN-P” will appear in the...

38For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
The original sound can be replaced with
new sound using the built-in Palmcorder
microphone.
Audio Dubbing using the
Built-in Microphone
1Set POWER to VCR.
2Press  (PLAY). Then press (PAUSE) where you  want dubbing to
begin.
3Press MENU to display the VCR
FUNCTIONS menu screen.
4Rotate JOG KEY to select
 RECORDING SETUP , then press
JOG KEY to display the RECORDING
SETUP menu screen....

39
Editing Features
Editing Features
6Press  (PAUSE) to start Audio
Dubbing. “A.DUB 
” indication
appears.
Connect the Palmcorder to the TV in
order to monitor the sound.
(p. 32)
Only NTSC (National Television Standards
Committee) recorded tapes can be audio
dubbed. The following screen appears if
the tape was not recorded in NTSC format.
7Press  (PAUSE) to stop Audio
Dubbing. To listen to the desired audio sound, set
the 12 bit AUDIO setting of the VCR mode
MENU (Menu OSD: p. 61) as follows:
If the...

40For assistance,  please call :  1-800-211-PANA(7262) or send e-mail to : [email protected]
Editing Features
Video In
VHF Connecting
Cable (not
supplied)TV
(To View)
A/V Cable
(Supplied)
To Audio In
To Video In
Recording:
VCR (Rear)
For technical reasons, dubbing a tape
may reduce its quality.
If the Time Code is displayed in the EVF
or LCD monitor, it cannot be reset.
Only the DATE/TIME, when displayed,
will be recorded on the tape.
    CAUTION:Unauthorized exchanging and/or
copying of...