Panasonic Pv Dc352 Operating Instructions Manual

							31
C
A
B
D
2
R
1 2
SEARCHSEARCHBACKLIGHT
1
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
VCR Mode
Playing Back
The recorded scene can be played back immediately after recording.
1Rotate the [OFF/ON/MODE] Switch and set the Palmcorder in 
the VCR Mode.
≥The [VCR] Lamp lights up. 1
2
Press the [6] Button to rewind the tape.
≥Rewind the tape to the point where you want to start playback.
≥When the tape reaches the beginning, rewinding stops automatically.
3Press the [1] Button to start playback.
To Stop Playback
Press the [∫] Button 2.
≥If a cassette recorded with copyright protection signals is played back, the 
screen becomes blue or mosaic-like noise patterns appear.
ªAdjusting the Sound Volume
Until the [VOLUME] Indication 3 appears, keep pressing the [PUSH] Dial 
4. Then, rotate the [PUSH] Dial to adjust the volume. After the adjustment, 
press the [PUSH] Dial to make the [VOLUME] Indication disappear.
To adjust the volume with the Remote Controller, press the [T] or [W] Button 
to display the [VOLUME] Indication. Press the [T] Button to increase the 
volume or press the [W] Button to decrease the volume. The [VOLUME] 
Indication goes off 2 or 3 seconds after the adjustment is finished.
≥When the Playback Zoom Function is in use, the sound volume cannot be 
adjusted.
≥For other notes, see page 63.
~~~~~~~~~~~~~~~~~~~~~~~~~
Finding a Scene You Want to Play Back
ªCue/Review Playback
Cue Playback A
Press the [5] Button 1 during playback.Review Playback BPress the [6] Button 2 during playback.
≥If the Button is held continuously, it remains as Cue Playback or Review 
Playback until you release it.
ªHyper Check Function
If you press the [5] Button during fast-forwarding of the tape or the [6] 
Button during rewinding of the tape, Cue Playback or Review Playback 
continues for as long as the Button is held down.
ªVariable Speed Search Function
The speed of Cue Playback or Review Playback can be varied.
1During playback, press the [1] Button.
≥[1k!] Indication appears. C
2
Rotate the [PUSH] Dial and select a desired search speed.
The following 6 playback speeds are available for the Variable Speed Search 
Function in both the fast-forwarding and rewinding directions. 1/5k (slow 
playback, SP mode only), 1/3k (slow playback, LP mode only),1k, 2k, 5k, 
10k, and 20k.
≥The same setting can be performed using the Remote Controller’s 
[VAR.SEARCH] Button, the [π] Button and the [∫] Button.
Resuming Normal Playback
Press the [1] Button.
≥During Cue or Review Playback, fast-moving images may show mosaic-like 
noise patterns. This is not a malfunction.
≥The sound is muted during search.
≥The Variable Speed Search feature is not available when the Repeat 
playback is active.
ªRepeat Playback
If you hold down the [1] Button for 5 seconds or longer, the Palmcorder 
switches to Repeat Playback Mode, and the [R !] Indication appears D. 
(To cancel Repeat Playback Mode, set the [OFF/ON/MODE] Switch to 
[OFF].)
3
1CAMERA
VCR
CARD 
P.B.
1
4PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
OFFONMODE
23
SEARCHSEARCH
MAGICPIX
BACKLIGHT
FADECAMERA STILL
MULTI/
P-IN-P TITLETELE JUMP
2
MJ147-P.book  31 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							32
2 1
33
ZOOM
INDEX INDEX
SELECT
STOPKL∫
OSDCOUNTER
V/REWSTILL ADV
DATE/
TIME
RESET
TITLE T
WsVO Lr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSEFF/W
STILL ADV61 5;ED
VA RPB
1PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
12BACKLIGHTCAMERA STILL
Slow Motion Playback
This Palmcorder can play back at a slow speed.
1Press the [1] Button.
2Press the [E] Button or the [D] Button on the Remote 
Controller.
≥When the [E] Button is pressed, Slow Motion Playback proceeds in the 
reverse direction, while pressing the [
D] Button starts Slow Motion 
Playback in the forward direction.
Scenes recorded in the SP mode are played back at approximately 1/5th of 
the normal speed.
Scenes recorded in the LP mode are played back at approximately 1/3rd of 
the normal speed.
Resuming Normal Playback
Press the [1] Button.
~~~~~~~~~~~~~~~~~~~~~~~~
Still Playback/Still Advance Playback
This Palmcorder is capable of still picture playback and frame-advance 
playback.
1Press the [1] Button.
2Press the [;] Button.
≥The playback image stops in the Still Playback Mode.
3Press the [E] Button or the [D] Button on the Remote 
Controller.
≥With each pressing of the [E] Button, still pictures advance in the 
reverse direction. With each pressing of the [
D] Button, still pictures 
advance in the forward direction. If either one of the buttons is pressed 
continuously, still pictures advance continuously one frame at a time 
until the button is released.
Resuming Normal Playback
Press the [1] Button or [;] Button.
ªJog Playback
By rotating the Jog Dial ([PUSH] Dial) 1 of the Palmcorder in the Still 
Playback Mode, still pictures can be advanced one frame at a time in the 
forward or reverse direction.
≥If the Palmcorder is left in the Still Playback Mode for more than 5 minutes, 
the Palmcorder switches to the Stop Mode to protect the video heads from 
excessive wear and tear.
~~~~~~~~~~~~~~~~~~~~~~~~Finding the End of a Recording (Blank Search Function)
The Blank Search Function helps you to locate the end of a recording on the 
Cassette quickly.
1Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[BLANK SEARCH] >> [YES].
≥The [BLANK] Indication 1 appears.
≥Approximately 1 second before the last recorded scene, the Palmcorder 
switches to the Still Playback Mode.
≥If there is no blank portion left on the cassette, the Palmcorder stops at 
the end of the tape.
Canceling Blank Search prior to completion
Press the [∫] Button.
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VA R .
SEARCHP.B.
ZOOM
1
2
2
BLANK1
1
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
MENU
MJ147-P.book  32 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							33
Index Search Functions
To facilitate searching of desired scene, this Palmcorder automatically 
records index signals during recording, as explained in the following.
PhotoShot Index Signal
These signals are automatically recorded whenever still pictures are taken in 
PhotoShot Mode (l 22).
When recording still pictures using the Continuous PhotoShot Mode (l 22), 
the index signal is not recorded.
Scene Index Signal
Scene Index Signals are automatically recorded when you start recording 
after inserting a Cassette.
However, if the Palmcorder is switched from the VCR Mode to Camera Mode, 
or if the date and time is set before the start of recording, the index signal is 
not recorded.
≥If [INDEX] of [RECORDING SETUP] Sub-Menu on the 
[CAMERA FUNCTIONS] Main-Menu is set to [2HOUR], an index signal is 
recorded when Recording is restarted after a lapse of 2 hours or longer. If it 
is set to [DAY], an index signal is recorded when recording is restarted after 
the date has changed since the last recording. (While the index signal is 
recorded, the [INDEX] indication 
A flashes for a few seconds.)
ªPhotoShot Index Search
1
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[INDEX] >> [PHOTO].
2Press the [9] Button or the [:] Button on the Remote 
Controller.
≥With each press of the corresponding button, still pictures recorded in 
PhotoShot Mode are searched.
≥After pictures with sounds are played back for 4 seconds, the Palmcorder 
switches to the Still Playback Mode.
ªScene Index Search
1
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[INDEX] >> [SCENE].
2Press the [9] Button or the [:] Button on the Remote 
Controller.
≥When the corresponding button is pressed once, the [S 1] Indication B 
appears, and searching of the subsequent scene marked with an index 
signal starts. Each time the button is pressed after the start of Scene Index 
Search, the indication changes from [S 2] to [S 9], and the beginning of the 
scene corresponding to the selected number will be searched. After 
reaching the desired scene, playback starts automatically.
≥Up to 9 scene numbers can be selected.
Top Scan
If the [9] Button or the [:] Button is pressed for more than 2 seconds, 
the Palmcorder will scan for scenes (or PhotoShots) and play back the first 
few seconds of each. (To cancel, press the [
1] Button 1 or the [∫] Button 
2
.)
≥For other notes, see page 64.
INDEX
S   1
A
B
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VA R .
SEARCHP.B.
ZOOM
1
2
2
1
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
MENU
MJ147-P.book  33 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							34
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
1
2
1
Playback Zoom Function
A part of the image can be enlarged up to 10 times during playback.
1During playback, press the [P.B. ZOOM] Button on the 
Remote Controller.
≥The center of the image is enlarged to approximately double the size.
Changing the Zoom Magnification
2Change the magnification by pressing the [W] or [T] Button 
on the Remote Controller.
≥You can increase the magnification up to 10k.
Changing the enlarged area of an image
3Press the Arrow Button (π, ∑, ∏, ∫) on the Remote 
controller that points to the area you want to enlarge.
≥When the playback is stopped, the position of the enlarged image area 
is reset to the center automatically.
Canceling the Playback Zoom Function
Press the [P.B. ZOOM] Button on the Remote Controller.
≥For other notes, see page 64.
~~~~~~~~~~~~~~~~~~~~~~~~
Playback Digital Effect Functions
During playback, special Digital Effects can be added to the Recording. The 
digital effects that may be applied in the process of recording (except Picture 
in Picture Mode) will be the same as these added effects.
1Press the [1] Button.
2Press the [SELECT] Button of the Remote Controller and 
select desired Digital Effect.
≥When the [SELECT] Button is pressed repeatedly, the Digital Effect 
selection changes.
MULTI )WIPE )MIX )STROBE )NEGA )SEPIA )MONO 
)TRAIL ) SOLARI )MOSAIC ) MIRROR
≥The same setting can also be set using the [DIGITAL EFFECT] on the 
[VCR FUNCTIONS] Main-Menu.
Suspending Playback Digital Effect Temporarily
Press the [OFF/ON] Button 1 to clear or restart the digital effect. When the 
digital effect is paused temporarily, the selected effect’s indication flashes.
Canceling the Digital Effect
Press the [SELECT] Button on the Remote Controller repeatedly until the 
Digital Effect Indication is cleared.
≥For other notes, see page 64.
ªPlayback with Wipe Mode and Mix Mode
1
Press the [1] Button to start playback.
2Press the [SELECT] Button on the Remote Controller and 
select [WIPE] or [MIX].
3Press the [STORE] Button at the moment you want to save 
as a still picture.
≥The last scene is stored in memory. The [WIPE] or [MIX] Indication 
changes to [B] or [C].
4Press the [OFF/ON] Button in the scene in which you want to 
use the Wipe or Mix effect.
≥The scene changes as a result of the Wipe or Mix effect.
≥The Wipe Function and Mix Function can be used only from the Remote 
Controller during playback.
≥If the [OFF/ON] Button is pressed while Wipe Function or Mix Function is 
used, the effect will stop temporarily at that point. Pressing the [OFF/ON] 
Button again will bring back the effect.
ZOOM 2t
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP. B .
ZOOM
2
1
3
WIPE
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP. B .
ZOOM
1
2
3
4
MIX
MJ147-P.book  34 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							35
1
2
3
3
2
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PA U S E
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP. B .
ZOOM
4
4
1, 2 1, 1
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
MENU
BACKLIGHTMULTI/
P-IN-P
ªPlaying Back with Multi-Picture Mode 
Strobe Multi-Picture Mode [STROBE] 1:
You can capture 9 consecutive still pictures from playback images.
Manual Multi-Picture Mode [MANUAL] 
2:
Selecting a desired still picture one at a time, you can capture 9 still pictures.
Index Multi-Picture Mode ([PHOTO], [SCENE]) 
3:
You can capture 9 screens of pictures to which index signals are attached.
After setting [VCR FUNCTIONS] >> [DIGITAL EFFECT] >> 
[EFFECT SELECT] >> [MULTI]...
1Set [MULTI-PICTURES] >> [SCAN MODE] >> [STROBE] or 
[MANUAL] or [PHOTO] or [SCENE], whichever mode you 
prefer.
When [STROBE] is selected:
≥Set the [SPEED] to a desired strobe speed.
[FAST]: You can capture 9 consecutive still pictures within 
approximately 1 second
[NORMAL]: You can capture 9 consecutive still pictures within 
approximately 1.5 seconds
[SLOW]:You can capture 9 consecutive still pictures within 
approximately 2 seconds
≥If you set [SWING] on the [MULTI-PICTURES] Sub-Menu to [ON], the 
intervals at which the 9 still pictures are taken are longer at the 
beginning and end than in the middle of the swing strobe period, and it 
is useful for analyzing swing motion, etc., in sports.
2Exit the Menu by pressing the [MENU] Button.
3Play back the tape.
≥If you select Index mode, it is not necessary to play back the tape.
4Press the [MULTI] Button.
≥If [STROBE] is selected: 9 screens are automatically captured from 
the point at which the Button is pressed.
≥If [MANUAL] is selected: press the [MULTI] Button at each scene you 
want to capture. When 9 screens are captured, the tape will stop.
≥If [PHOTO] or [SCENE] is selected: From the point at which the 
Button is pressed, 9 screens of pictures to which index signals are 
attached are captured in the playback direction. After 9 screens are 
captured, the tape will stop, but, if there are 8 or less pictures to be 
captured, the tape will stop at its end.
Deleting All the Captured Multi-Pictures
While displaying the multi-pictures that have been captured, press the 
[MULTI] Button.
≥If [MANUAL] has been selected, press [MULTI] Button after 9 screens are 
displayed.
To Display the Multi-Pictures again
Press the [MULTI] Button for 1 second or longer.
To Delete Multi-Pictures one by one  (When Pictures have been 
captured in Manual Mode)
When the [MULTI] Button is pressed for 1 second or longer while the still 
pictures are displayed, the picture that was captured last is deleted. If you 
continue to press the Button, the pictures are deleted consecutively.
≥After still pictures are deleted one at a time, they cannot be displayed again.
To Stop Capturing Pictures midway (When Pictures have been 
captured in Index Mode)
Press the [∫] Button.
To Search the tape position of a desired picture among the 
playback pictures displayed on 9 screens
1
11 1After displaying pictures in Multi-Picture Mode, rotate the 
[PUSH] Dial to select the image whose tape position you 
want to search.
≥The selected picture is marked with a red frame.
2
22 2Press the Index Button [:] or [9] 4 on the Remote 
controller.
≥Still picture playback takes place at the selected picture.
≥For other notes, see page 64.
147P_text.fm  35 ページ  ２ ０ ０ ２年４月２ ４日　水曜日　午後３時２分 
						

							36
A.DUB;A.DUB!12
1, 2
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
MENU
3
4
ZOOM
INDEX INDEX
SELECT
STOPKL∫
OSD
COUNTER
V/REW
STILL ADV
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S E
FF/W
STILL ADV61 5
;ED
VAR.
SEARCHP. B .
ZOOM
Playing Back on Your TV
By connecting your Palmcorder to your TV, the recorded scenes can be 
viewed on your TV screen.
≥Before connecting them, turn off the power of both the Palmcorder and TV.
1Connect the [A/V OUT] Jack of the Palmcorder to the Video 
and Audio Input Jacks of the TV.
≥Using the A/V Cable 1 (supplied), make a connection with the TV. If 
the TV has an S-Video Jack, connect an S-Video Cable (not supplied) 
2, too.
Making the Indications Appear on the TV screen
Press the [OSD] Button 3 on the Remote Controller.
≥Be sure to select the proper input on your TV. (If necessary, consult your 
TV’s operating instructions.)
≥If you play back a Cassette recorded with copyright protection signals, the 
screen becomes blue or mosaic-like noise patterns appear.
≥If you set [AV JACK] on the [AV IN/OUT SETUP] Sub-Menu to [IN/OUT], 
nothing will be shown on the TV screen except during playback.
~~~~~~~~~~~~~~~~~~~~~~~~
Audio Dubbing
You can add music or narration to the recorded Cassette.
≥If you perform audio dubbing onto a tape that was recorded with 
[AUDIO-REC] on the [RECORDING SETUP] Sub-Menu of the 
[CAMERA FUNCTIONS] Main-Menu set to [16bit], the original sound is 
erased.
 (If you want to preserve the original sound, use the [12bit] Mode 
when recording.)
≥Audio Dubbing cannot be performed onto recordings made in LP Mode. 
(l20)
1Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >> [AV JACK] 
>> [IN/OUT].
2Continuing the aforesaid setup, select [A.DUB INPUT] >> 
[MIC] or [AV IN].
≥Set to [AV IN] when external device is used, and to [MIC] when an 
external or built-in microphone is used.
≥Switch the Palmcorder over to the Still Playback Mode where you want 
to add new sound track.
3Press the [A.DUB] Button on the Remote Controller.
≥[A.DUB;] Indication appears. 1
4
To start Audio Dubbing, press the [;] Button on the Remote 
Controller.
≥[A.DUB!] Indication appears. 2
To Stop Audio Dubbing
Press the [;] Button on the Remote Controller.
The Palmcorder is in the Still Playback Mode again.
Playing Back the Sound Recorded with Audio Dubbing
(For 12 bit Audio Recording)
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> [AUDIO] >> [ST2] 
or [MIX].
ST1: Play back only the original sound.
ST2: Play back only the sound added by Audio Dubbing
MIX: Play back both the original sound and the sound added by Audio 
Dubbing simultaneously.
≥For other notes, see page 64.
1
2
[VIDEO IN]
[AUDIO IN][S-VIDEO IN]
1
ZOOM
INDEX INDEX
SELECT
STOPKL∫
OSD
COUNTER
V/REW
STILL ADV
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV61 5
;ED
3
S-VIDEO
    IN/OUTA/V IN/OUT  PHONES/
  REMOTE
MJ147-P.book  36 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							37
4
1, 2
F 7640PICTURE
1
4
TAPECARDCARD MODE
PHOTOSHOT
3
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
MENU
MPEG4
2
VOICE
3
2A
1
13
Special Features
Using a Memory Card
A Card can be used to record files or play back files.
≥Use a genuine SD Memory Card or MultiMediaCard only.
ªInserting a Memory Card
Before inserting a Memory Card, be sure to turn off the Palmcorder.
1Open the Card Slot Cover.
2While holding the Memory Card with its cut corner A facing 
right, insert it into the Card Slot.
3Close the Card Slot Cover securely.
ªRemoving the Memory Card
Open the Card Slot Cover, press the centre of the Card and then pull it 
straight out.
≥After removing the Card, close the Card Slot Cover.
≥The Palmcorder or the Card may be damaged if the Card is forced out when 
the Card is fully inserted.
ª[ACCESS] Lamp
While the Palmcorder is accessing the Card (reading, recording, playback, 
erasing, moving of images), the [ACCESS] Lamp 1 lights up.
≥While the [ACCESS] Lamp is on, never attempt to: pull out the Card, to turn 
off the Palmcorder power, or switch the [TAPE/CARD/CARD MODE] 
Selector. Such actions will damage the Card and cause the Palmcorder to 
malfunction.
~~~~~~~~~~~~~~~~~~~~~~~~~
Recording on the Memory Card
3 kinds of data can be recorded by selecting with the [TAPE/CARD/
CARD MODE] Selector. When recording still picture, slide the [TAPE/CARD/
CARD MODE] Selector until the [PICTURE] Indication 
1 appears (Card 
PhotoShot), when recording a moving picture, slide the [TAPE/CARD/
CARD MODE] Selector until the [MPEG4] Indication 
2 appears (MPEG4 
Recording), when recording voice, slide the [TAPE/CARD/CARD MODE] 
Selector until the [VOICE] Indication 
3 appears (Voice Recording).
≥For other notes, see page 64.
ªCard PhotoShot
Still pictures can be recorded on the Memory Card from the Palmcorder lens 
as well as from scenes that have already been recorded on a cassette.
The size of images that are recorded using this Palmcorder is approximately 
1,230,000 pixels. Recording of images with a size that is larger than a million 
pixels is called mega-pixel still-picture recording. Compared to images of 
normal recording, images that are created by mega-pixel still-picture 
recording can be printed out more clearly.
Recording from the Palmcorder Lens (Camera Mode)
1Slide the [TAPE/CARD/CARD MODE] Selector to [CARD].
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [PICTURE] Indication appears.
≥Remaining Number of Card PhotoShot pictures 4.
3Set [CAMERA FUNCTIONS] >> [CARD SETUP] >> 
[PICTURE SIZE] >> [1280k
kk k960] or [640k
kk k480].
4Press the [PHOTO SHOT] Button.
≥The [ ] Indication will light in red.
≥Mega-pixel recording (when you select [1280k960] in step 3) is useful for 
taking clear pictures, but the following functions are disabled during 
mega-pixel recording.
≥Title In/Creation (l43)
≥The power automatically turns off about 5 minutes after a card has been 
inserted.
≥With the Progressive PhotoShot Function, you can record still pictures with 
higher resolution than with the normal PhotoShot Function (l22).
≥For other notes, see page 64.PICTURE
MJ147-P.book  37 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							38
F 7640PICTURE
4, 4 1, 2
2, 3
PHOTOSHOT3, 1, 1
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOGMENU
TAPECARDCARD MODE
ªCard PhotoShot (continued)
Recording from a Cassette (VCR Mode)
1Slide the [TAPE/CARD/CARD MODE] Selector to [CARD].
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [PICTURE] Indication appears.
3Set [VCR FUNCTIONS] >> [CARD SETUP] >> 
[PICTURE QUALITY] >> a desired picture quality.
4Start playback and press the [PHOTO SHOT] Button at the 
scene you want to record.
≥While the image is being recorded, it stays still for a few seconds.
Recording from other equipment 
1
11 1Set [CAMERA FUNCTIONS] or [VCR FUNCTIONS] >> 
[CARD SETUP] >> [PICTURE QUALITY] >> a desired picture 
quality.
2
22 2Slide the [TAPE/CARD/CARD MODE] Selector to [CARD].
3
33 3Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [PICTURE] Indication appears.
4
44 4Input the picture from the other equipment then press the 
[PHOTO SHOT] Button at the desired scene.
Selecting the quality of Card PhotoShot images
1Set [CAMERA FUNCTIONS] or [VCR FUNCTIONS] >> 
[CARD SETUP] >> [PICTURE QUALITY] >> a desired picture 
quality.
Maximum number of images recordable on the supplied Card (16 MB)
When the picture size is 1280t960:
[FINE] (high image quality): approximately 22 pictures
[NORMAL] (Normal): approximately 35 pictures
[ECONOMY] (low image quality): approximately 50 pictures
When the picture size is 640t480:
[FINE] (high image quality): approximately 100 pictures
[NORMAL] (Normal): approximately 200 pictures
[ECONOMY] (low image quality): approximately 400 pictures
≥The figures vary depending on the subject being photographed.
ªAutomatically copying still pictures recorded on a 
cassette
The Palmcorder copies images automatically, referring to Photo Index 
signals.
After setting the Palmcorder to the VCR Mode (l 31).....
1Set the Palmcorder to Still Playback Mode just before the 
point where picture transfer is to commence.
2Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[RECORD TO CARD] >> [YES].
≥Search starts from the current Cassette position, and images with 
Photo Index signals are recorded onto the Card sequentially.
≥While copying, the Indication 
1 appears.
To Stop the Transfer of Images
Press the [∫] Button.
≥For other notes, see page 65.
1
NOW WRITING;
TAPE
CARD%
1
2
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
MENU
CAMERA STILL
MJ147-P.book  38 ページ  ２００２年４月２４日　水曜日　午後１時５６分 
						

							39
R:0h20mMPEG4
R:0h20mVOICE
1, 2
TAPECARDCARD MODE
OFFONMODE
3
1
PUSHW.B./SHUTTER/IRIS/
MF/VOL/JOG
MENU
ªRecording Moving Pictures (MPEG4)
You can record moving pictures on a Memory Card for e-mailing. The 
recorded data can be also played back on a computer with Windows Media 
Player.
Recording from the Palmcorder Lens (Camera Mode)
1Slide the [TAPE/CARD/CARD MODE] Selector to [CARD].
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [MPEG4] Indication appears.
3Press the Recording Start/Stop Button.
≥It takes 2 to 3 seconds to start recording.
≥During recording, the [ ] Indication is lit in red. 
≥The maximum continuous recording times are:
[FINE] (high image quality): 2 minutes
[NORMAL] (normal image quality): 120 minutes
The Palmcorder will automatically stop recording when the approximate 
time listed above has elapsed (the card capacity has been fully utilized).
Recording from a Cassette (VCR Mode)
1Slide the [TAPE/CARD/CARD MODE] Selector to [CARD].
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [MPEG4] Indication appears.
3Start playback and press the Recording Start/Stop Button at 
the desired scene.
Recording from other equipment (VCR Mode)
1Slide the [TAPE/CARD/CARD MODE] Selector to [CARD].
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [MPEG4] Indication appears.
3Input the image from other equipment then press the 
Recording Start/Stop Button at the desired scene.
Selecting the quality of MPEG4 Recording images
1
11 1Set [CAMERA FUNCTIONS] or [VCR FUNCTIONS] >> 
[CARD SETUP] >> [MPEG4 MODE] >> a desired image 
quality.
Maximum recording time on the supplied Card (16 MB)
[FINE]: approximately 5 minutes
[NORMAL]: approximately 15 minutes
≥The video resolution of the camera is reduced when making an MPEG4 
recording. This is done in order to optimize the image quality in MPEG4 
recordings, and does not reflect that there is a problem with the software or 
hardware.
≥For other notes, see page 65.
ªRecording Voice (Voice Recording Function)
You can record voice data on a memory card.
1Slide the [TAPE/CARD/CARD MODE] Selector to [CARD].
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [VOICE] Indication appears.
3Press the Recording Start/Stop Button.
≥Voice from built-in microphone is recorded.
≥It takes 2 to 3 seconds to start recording.
≥The recorded file is automatically locked (to prevent accidental 
erasure).
≥Voice from external microphone connected to the microphone jack can 
also be recorded.
≥During recording, the [ ] Indication is lit in red. 
≥When Remaining Time Indication becomes [R:0h00m], 
[NO SPACE LEFT] Indication appears. Recording may not be started.
Maximum recording time on the supplied Card (16MB)
Approximately 58 minutes
≥For other notes, see page 65.
MPEG4MPEG4
VOICE
147P_text.fm  39 ページ  ２ ０ ０ ２年４月２ ４日　水曜日　午後３時６分 
						

							40
Playing Back Files from the Memory Card
You can play back files recorded on a Card.
≥When you set the Palmcorder to Card Playback Mode, the card contents 1 
are displayed to inform you of the type of data (still picture, moving picture 
and/or voice data) recorded on the Card.
ªPlaying back Still Pictures
1
Set the Palmcorder to Card Playback Mode.≥The [CARD P.B.] Lamp lights up.
≥The still picture that was recorded last on the Card is displayed.
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [PICTURE] Indication appears.
3Start Playback.1: Starts Slide Show (The [SLIDE!] Indication is displayed)
5: Playing back the next picture
6: Playing back the previous picture
∫: Stop the slide playback
;: Pause slide playback
ªPlaying back Moving Pictures (MPEG4) 
1
Set the Palmcorder to Card Playback Mode.≥The [CARD P.B.] Lamp lights up.
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [MPEG4] Indication appears.
3Start Playback.1: Playing back
∫: Stop playback
;: Pause playback (This button does not pause playback within 2 seconds 
of finishing playback.)
5: (Stop Mode) To the beginning of the next file.
(Playback Mode) To the beginning of the next file picture and start playback.
(Pause Mode) To the beginning of the next file and turns to Stop Mode.
6: (Stop Mode) To the beginning of the previous playback file.
(Playback Mode) To the beginning of the playback file and start playback.
(Pause Mode) To the beginning of the file under playback and turns to 
Stop Mode.
≥File is numbered in hexadecimal form.
≥When the object is moving fast or zoom operation is performed, picture may 
appear to be still or a mosaic noise pattern appears, but this is not a 
malfunction.
ªPlaying back Voice recordings
1
Set the Palmcorder to Card Playback Mode.≥The [CARD P.B.] Lamp lights up.
2Slide the [TAPE/CARD/CARD MODE] Selector to 
[CARD MODE] until the [VOICE] Indication appears.
3Start Playback.1: Playing back
∫: Stop the playback
;: Pause playback (This button does not pause playback within 2 seconds 
of finishing playback).
5: (Stop Mode) To the beginning of the next File.
(Playback Mode) To the beginning of the next File and start playback. 
(Pause Mode) To the beginning of the next File and turns to Stop Mode.
6: (Stop Mode) To the beginning of the previous playback File.
(Playback Mode) To the beginning of the playback File and start playback.(Pause Mode) To the beginning of playback File and turns to Stop Mode.≥If the [6] Button or [5] Button is pressed for 1 or more seconds during 
playback, it becomes 10k playback speed and if pushed for 7 or more 
seconds, it becomes 60k playback speed. Releasing the button brings it 
back to normal playback.
2Folder-File Number (When the picture is played back)
File Name (When the MPEG4 data is played back) 
3 Picture Size (When the picture is played back) (l59)
Playback time (When MPEG4 data or Voice data is played back)
4 File Number (When pictures are played back)
To adjust the volume (Only when playing back MPEG4 and Voice 
Recordings)
≥During playback, hold down the [PUSH] Dial until the volume indication 
appears and rotate it to adjust the volume. (l31)
1
3
4
MPEG4
3
4 2
VOICE
CARD CONTENTS
PICTURE
MPEG4
VOICE
2
3
4
100-0012
3
2
TAPECARDCARD MODE
CAMERA
VCR
CARD 
P.B.
OFFONMODE
SEARCHSEARCH
MAGICPIX
BACKLIGHT
FADECAMERA STILL
MULTI/
P-IN-P TITLETELE JUMP
1
MJ147-P.book  40 ページ  ２００２年４月２４日　水曜日　午後１時５６分