Panasonic Protocol Converter Aw If400g Operating Instructions

Protocol Converter
AW-IF400G
Before attempting to connect, operate or adjust this product,  
please read these instructions completely.
FRANÇAIS
DEUTSCH
ENGLISH
ITALIANO
ESPAÑOL
中
  
文
ÔŠ 
Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Stampato in Giappone
Impreso en Japón
Напечатано в Японии
在日本印制
Matsushita Electric Industrial Co., Ltd.Web Site: h t t p : / / p a n a s o n i c . n e t
	¦<?+ˆÀÒÜqþyÒé”ÅÝßžŠ
æ
ßy#
¿¢ÓzàÝaf¸è
jøyy
Ñ攼...

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, 
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The  lightning  flash  with  arrowhead  symbol, 
within  an  equilateral  triangle,  is  intended  to 
alert  the  user  to  the  presence  of  uninsulated 
“ d a n g e r o u s   vo l t a g e ”  w i t h i n   t h e   p r o d u c t ’s 
enclosure  that  may  be  of  sufficient  magnitude 
t o   c o n s...

- 2 (E) -
ENGLISH
 indicates safety information.
CAUTION:
TO   R E D U C E   T H E   R I S K   O F   F I R E   O R   S H O C K 
HAZARD  AND  ANNOYING  INTERFERENCE,  USE 
THE RECOMMENDED ACCESSORIES ONLY.
Note:
The  rating  plate  (serial  number  plate)  is  on  the 
bottom of the unit.
WARNING:
•  TO  REDUCE  THE  RISK  OF  FIRE  OR  ELECTRIC SHOCK,  DO  NOT  EXPOSE THIS  APPARATUS TO 
RAIN OR MOISTURE.
•  THE  APPARATUS  SHALL  NOT  BE  EXPOSED TO 
 
D R I P P I N G   O R   S P L A S H I N G   A N D...

- 3 (E) -
 indicates safety information.
  1) Read these instructions.
  2) Keep these instructions.
  3) Heed all warnings.
  4) Follow all instructions.
  5) Do not use this apparatus near water.
  6) Clean only with dry cloth.
  7)  Do  not  block  any  ventilation  openings.  Install  in accordance with the manufacturer's instructions.
  8)  Do  not  install  near  any  heat  sources  such  as 
 
radiators, heat registers, stoves, or other apparatus 
(including amplifiers) that produce heat....

- 4 (E) -
ENGLISH

• Power Off Before Connecting or Disconnecting Cables.
   Before plugging or unplugging the cables, be sure to switch power off.
• Handle Carefully.
   Do not drop the product, or subject it to strong shock or  vibration. This is important to prevent trouble. • Avoid Humidity and Dust.
   Avoid using the product at a humid, dusty place because 
much humidity and dust will cause damage to the parts 
inside.
• Operating Temperature Range
   Avoid using the product at a cold place below...

- 5 (E) -

Introduction
By using this unit, AW-PH400 can be controlled from AW-RP605/AW-RP605A/AW-RP655/AW-RP555.
Additionally, the controllable distance between AW-RP400 and AW-PH400/AW-PH360 can be extended up to 
 
3,280 feet (1,000 meters). 
AW-PH350/AW-PH360/AW-PH650 can also be controlled from AW-RP400.
Notes
  The connections other than above examples cannot be done.
  When controlling the AW-PH400 from the AW-RP605A:
• The AW-PH400 has no backlash so it is not necessary to adjust the backlash...

- 6 (E) -
ENGLISH

Major operating controls and their functions
 Power LED [POWER]This lights up green when DC power is supplied to the DC 
12 V input connector 
.
 Transmission Status LED [COMMUNICATE]This lights up when data is being transmitted between the 
controller and pan/tilt head.
 Extended Distance Transmission LED [EXTENSION]This lights up when this unit is used to extend the 
transmission distance between AW-RP400 and 
 
AW-PH400.
Front panel 

- 7 (E) -

Major operating controls and their functions
Rear panel
 Controller connector [CONTROLLER]Use the controller CONTROL OUT TO PAN/TILT terminal 
and a 10BASE-T (equivalent to UTP category 5) straight 
cable for connection. Pan/tilt head connector [PAN-TILT HEAD]Use the pan/tilt head IP/RP terminal and a 10BASE-T 
 
(equivalent to UTP category 5) straight cable for 
connection. 

- 8 (E) -
ENGLISH

Major operating controls and their functions
 Function Switches [SW1, SW2, SET UP](Factory defaults: SW1 = OFF, SW2 = OFF, 
 
SET UP No.1 = ON, SET UP No.2 to 4 = OFF)
 
This is used to select the operations of the AW-IF400.
Before changing a setting, the power must be turned off.
SETUP No.3 is the tilt range selector switch which is used 
to control the AW-PH400 from the AW-RP605A.
At the ON position, the range is 300 degrees; at the OFF 
position, it is 190 degrees. For any other...

- 9 (E) -

Connections
• Before proceeding with the connections, turn off the power.
•  For further details on connecting the devices, refer to the operating instructions accompanying the devices concerned.
•  For further details on operating the devices, refer to the operating instructions accompanying  the devices concerned.
• Use a separate cable compensator if the video signal cable is longer than 500 meters.