Panasonic Projector Pt Lz370u Operating Instructions

							[NETWORK] menu
ENGLISH - 91
Settings
▶■[Authentication set up] page
You can set the authentication items when POP authentication or SMTP authentication is necessary to send 
an E-mail message.
Click [Detailed set up] 
→ [Authentication set up].
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(1) [Auth] Select the authentication method specified by your 
Internet service provider.
(2) [SMTP Auth] Set when the SMTP authentication is selected.
(3) [POP server name] Enter the POP server name. (Up to 63 characters in 
single byte)
Allowed characters:
Alphanumerics (A to Z, a to z, 0 to 9)
Minus sign (-) and period (.)
(4) [User name] Enter the user name for the POP server or the SMTP 
server. (Up to 63 characters in single byte)
(5) [Password] Enter the password for the POP server or the SMTP 
server. (Up to 63 characters in single byte)
(6) [SMTP server port] Enter the port number for the SMTP server.
(Normally 25)
(7) [POP server port] Enter the port number for the POP server.
(Normally 110)
(8) [Submit] Update the settings. 
						

							[NETWORK] menu
92 - ENGLISH
Settings
▶■Contents of mail sent
▶z
Example of E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been established.
▶zExample of E-mail sent for an error
The following E-mail is sent when an error has occurred. 
						

							[NETWORK] menu
ENGLISH - 93
Settings
▶■[Command port set up] page
Set the port number used for command control.
Click [Detailed set up] 
→ [Command port set up].
(1)
(2)
(1) [COMMAND PORT]
Set the port number used for command control.
(2) [Set command port] Update the settings.
▶■[Change password] page
Click [Change password].
(1)
(2)
(3)
(1) [Administrator]
Used to change the setting of [Administrator].
(2) [User] Used to change the setting of [User].
(3) [Next] Used to change the setting of the password.
 z[Administrator] account
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(1) [Account] Displays the account to change.
(2) [Current] [User name] Enter the user name before the change.
(3) [Current] [Password] Enter the current password.
(4) [New] [User name] Enter the desired new user name. (Up to 16 characters in 
single byte)
(5) [New] [Password] Enter the desired new password. (Up to 16 characters in 
single byte)
(6) [New] [Password(Retype)] Enter the desired new password again.
(7) [OK] Determines the change of password. 
						

							[NETWORK] menu
94 - ENGLISH
Settings
 z[User] account
(1)
(2)
(3)
(5) (4)
(1) [Account]
Displays the account to change.
(2) [New] [User name] Enter the desired new user name. (Up to 16 characters in 
single byte)
(3) [New] [Password] Enter the desired new password. (Up to 16 characters in 
single byte)
(4) [New] [Password(Retype)] Enter the desired new password again.
(5) [OK] Determines the change of password.
 z[Change password] (For user rights)
Only the change of password is enabled under the user rights.
(1)
(2)
(4) (3)
(1) [Old Password]
Enter the current password.
(2) [New Password] Enter the desired new password. (Up to 16 characters in 
single byte)
(3) [Retype] Enter the desired new password again.
(4) [OK] Determines the change of password.
Note
 zT

o change the account of the administrator, it is required to enter [User name] and [Password] in [Current]. 
						

							[NETWORK] menu
ENGLISH - 95
Settings
▶■[CRESTRON RoomV iew] page
You can monitor/control the projector using RoomView.
To display the operation page of RoomView from Web Control screen, access with the administrator rights is 
required. (The [CRESTRON RoomView] button is not displayed on the Web Control screen for user rights.)
When you click [CRESTRON RoomView], the RoomView operation page is displayed.
If Adobe Flash Player is not installed in your computer, or if the browser does not support Flash, this page 
does not appear. In this case, return to the previous page by clicking [Back] in the operation page.
▶z
Operation page
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(1) [Tools] [Info] [Help]
Switches the pages for tools/information/help using the tab.
(2) [POWER] Switches between on and off of the power.
(3) [VOL DOWN] [AV MUTE] [VOL UP] Sets the volume/AV mute.
When the power of the projector is turned off, [VOL DOWN], 
[AV MUTE], and [VOL UP] are not available.
(4) [Input Select] Sets the input selection. 
When the power of the projector is turned off, this operation 
is not available.
(5) Operation buttons on the menu screen Operates on the menu screen.
(6) Freeze/image quality adjustment Sets freeze/image quality details.
(7) [Back] Returns to the previous page.
▶z[T ools] page
Click [Tools] on the operation page.
(1)
(2)
(3)
(4)
(5)
(1) [Control System]
Sets the information required for the communication with 
the controller that is connected to the projector.
(2) [User Password] Sets the password for the user rights in  the operation page 
of RoomView.
(3) [Admin Password] Sets the password for the administrator rights in  the 
operation page of RoomView.
(4) Network status Displays the setting of wired LAN.
[DHCP] Displays the value in the current setting.
[Ip Address] Displays the value in the current setting.
[Subnet Mask] Displays the value in the current setting.
[Default Gateway] Displays the value in the current setting.
[DNS Server] Displays the value in the current setting.
(5) [Exit] Returns to the operation page. 
						

							[NETWORK] menu
96 - ENGLISH
Settings
▶z[Info] page
Click [Info] on the operation page.
(4)(5)
(6)
(7)
(1)
(2)
(3)
(8)
(1) [Projector Name]
Displays the name of the projector.
(2) [Mac Address] Displays the MAC address.
(3) [Lamp Hours] Displays the lamp usage time (converted value).
(4) [Power Status] Displays the status of the power.
(5) [Source] Displays the selected video input.
(6) [Lamp Mode] Displays the lamp mode.
(7) [Error Status] Displays the error status.
(8) [exit] Returns to the operation page.
▶z[Help] page
Click [Help] on the operation page.
The [Help Desk] screen is displayed.
(1)
(1) [Help Desk]
Sends or receive messages to the administrator who uses 
Crestron RoomView. 
						

							 and  indicators
ENGLISH - 97
Maintenance
 and  indicators
Managing the indicated problems
If a problem should occur inside the projector, the lamp indicator  and the temperature indicator  
will inform you.
Manage the indicated problems as follows.Attention
 z When switching of

f the power to deal with problems, make sure to follow the procedure in “Switching of f the 
projector” (
 page 38).
Note
 z Check the status of the power supply with the power indicator . (
 page 36)
7HPSHUDWXUHLQGLFDWRU7(03!/DPSLQGLFDWRU/$03!
▶■Lamp indicator 
Indicator 
status Illuminating red
Flashing red
Problem Time to replace the lamp unit. 
(
 page 103) Lamp circuit failure, abnormal function, or lamp unit is 
damaged.
Cause
 z Is [REPLACE LAMP] displayed when 
you turned on the power?
 zThe indicator illuminates when the 
lamp usage time (converted value)*1 
reaches 2 800 hours.
 z Have you turned 
on the power again 
immediately after 
turning it of

f?
 zLamp circuit failure, 
abnormal function, or lamp 
unit is damaged.
Solution
 z Replace the lamp unit. zW

ait a while until 
the luminous lamp 
cools off and turn 
off the main power, 
and then turn on the 
power again.
 z T

urn the  
switch to  
(
 page 38), and consult 
your dealer .
*1: The lamp usage time (converted value) is displayed in the [PROJECT OR SETUP] menu 
→ [LAMP
 RUNTIME] ( page 68).
Note
 zIf the lamp indicator  is still illuminating or flashing after taking the preceding measures, ask your 
dealer to repair the unit. 
						

							 and  indicators 
98 - ENGLISH
Maintenance
▶■Temperature indicator 
Indicator 
status
 z Illuminates red during projection.
(The message [REFER 

TO THE “TEMP indicator” SECTION IN THE OPERATION MANUAL.] 
is displayed on the projection screen.)
 z Flashing red when the power is turned of

f (projection stops automatically).
Problem The temperature inside and/or outside the projector is abnormally high.
Cause
 z Is the ventilating 
p

ort (intake/exhaust) 
blocked?
 z Is the room 
temperature too 
high? zIs the air filter unit 
clogged? zIs the projector used 
at high elevations 
1

  400   m (4   593   ft) or 
higher sea level?
Solution
 z Remove any objects 
that are blocking 
the ventilating port 
(intake/exhaust). zPlace the projector 
in an environment 
with temperature 
and humidity as 
designated in the 
specifications. 
(
 page 119)
 zClean or replace 
the air filter unit. 
(
 page 99)
 zThe projector can 
only be used for two 
m

inutes after turning 
on the power. Set 
[HIGH ALTITUDE 
MODE] (
 page 67) 
to [ON] within two 
minutes of turning 
on the power.
Note
 z If the temperature indicator  is still illuminating or flashing after taking the preceding measures, ask 
your dealer to repair the unit. 
						

							Maintenance/replacement
ENGLISH - 99
Maintenance
Maintenance/replacement
Before maintaining/replacing the unit
 zMake sure to turn of
f the power before maintaining or replacing the unit. ( pages 35, 38)
 zWhen turning of

f the power, make sure to follow the procedures in “Switching off the projector” (
 page 38).
Maintenance
▶■ Outer case
Wipe off dirt and dust with a soft, dry cloth.
▶z
If the dirt is persistent, soak the cloth with water and wring it thoroughly before wiping. Dry of
f the projector 
with a dry cloth.
▶z Do not use benzene, thinner

, or rubbing alcohol, other solvents, or household cleaners. Using them may 
cause deterioration of the outer case.
▶z When using chemical treated dusters, follow the instructions.
▶■ Lens
If dirt or dust accumulates on the surface of the lens, it will be enlarged and projected onto the screen.
Wipe off dirt and dust off the front surface of the lens with a soft clean cloth.
▶z
Do not use a cloth that is fluf

fy, dusty, or soaked with oil/water.
▶zDo not use excessive force when wiping the lens as it is fragile.
Attention
 z The lens is made of glass. Impacts or excessive force when wiping may scratch its surface. Please handle with 
care.
▶■ Air filter unit
If too much dust accumulates in the air filter unit, the internal temperature of the projector cannot be 
maintained at the normal level. A confirmation message is displayed on the screen, and at the same time 
the temperature indicator  illuminates red. The power is cut off automatically after a while. In such a 
case, clean the air filter unit.
1) Remove the air filter cover
.
▶zUse a Phillips screwdriver to turn the air filter cover fixing screw until it turns freely
, and then remove the air 
filter cover .
Air filter cover f\
ixing screw
Air filter cover 
						

							Maintenance/replacement 
100 - ENGLISH
Maintenance
2) Pull out the air filter unit.
▶zHold the grips on the air filter unit and pull out the air filter unit from the projector
.
Air filter unit
Grips (arrow engra\vve\f)
• After removing the air filter unit, remove any large build ups of dirt or dust in the air filter unit bay and the 
air intake port on the projector
.
3) Clean the air filter unit.
▶zVacuum dirt and dust from the air filter unit.
4) Attach the air filter unit to the projector
.
▶zPerform Step  2) in the reverse order.
•  
Insert the air filter unit into the projector in the direction of the arrow engraved into the air filter frame () 
until it clicks into place.
5) Attach the air filter cover to the projector and use a Phillips screwdriver to tighten 
the air filter cover fixing screw (one screw).
▶z Perform Step  1) in the reverse order.
Attention
 z Make sure that the air filter is properly attached before using the projector
. If it is not properly attached, the 
projector will suck in dirt and dust causing a malfunction.
 z Do not use water to wash the air filter unit. Doing so decreases its ability to absorb dust.