Panasonic Projector Pt Lb30ntu Operating Instructions

ENGLISH-41
Adjustments and settings
Press the For Gbutton on the
projector or remote control unit to
select an item, and then press the I
or Hbutton to change the setting.
For items with bar scales, press the
ENTER button or the Ior Hbutton
to display the adjustment screen,
and then press the Ior Hbutton
to make the adjustment.
When an RGB/YP
BPRsignal is
being input
When an S-VIDEO/VIDEO signal is
being input
POSITION
Moves the picture position.
Press the ENTER button to display the
“POSITION” screen....

42-ENGLISH
S4:3
The size of the input signal is
compressed to 75% and projected.
(This is useful for projecting a
picture with a 4:3 aspect ratio onto a
16:9 screen.)
AUTO
(S-VIDEO only)
When an S1 video signal is being
input, the aspect ratio is changed
automatically to project a 16:9
picture.
4:3
The input signal is projected without
change.
16:9
The picture is compressed to a ratio
of 16:9 and projected.
ASPECT         AUTO                                [                4:3...

RESIZING
This should normally be set to “ON”.
(This setting is only for signals
which have lower resolutions than
the LCD panels. Refer to page 62
for details.)
ON
The pixel resolution of the input
signal is converted to the same
resolution as the LCD panels before
being projected. 
This may sometimes cause
problems with the quality of the
picture.
OFF
The input signal is projected at its
original resolution, with no pixel
conversion. The projected picture
will be smaller than normal, so
adjust the zoom...

44-ENGLISH
Changing the display language
Press the For Gbutton on the projector or remote control unit to select a
language, then press the ENTER button to accept the setting.
Indicates the language which is
currently set.
   LANGUAGE    ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
PORTUGUÊS
SVENSKA
NORSK
DANSK
POLSKI
CESTINA
MAGYAR
yyyyyyyyyyyyyyyyyyyyÝ  SELECT  ENTER  RETRN
   LANGUAGE    ENGLISH
yyyyyyyyyyyyyyyyyyyyÛ
ENGLISH¤
ÔŠ 
  SELECT  ENTER  RETRN 

ENGLISH-45
Adjustments and settings
Option settings
Press the For Gbutton on the
projector or remote control unit to
select an item, then press the Ior
Hbutton to change the setting.
        OPTIONyyyyyyyyyyyyyyyyyyyyÛBACK COLOR     BLUE
FRONT/REAR    FRONT
DESK/CEILING   DESK
FAN CONTROL  STANDARD
LAMP POWER     HIGH
LAMP RUNTIME   10H
FUNC 1       DAYLIGHT
CONTROL KEY     ON
AUTO POW.OFF DISABLE
POWER MEMORY    ON
  SELECT  ADJ    RETRN
NOTE:
BThe setting for “TV-SYSTEM”
will also...

46-ENGLISH
RGB2 SELECT
This setting is used to select the
function of the RGB2 IN/1 OUT
connector.
RGB/YPBPR
This should normally be set to
“AUTO”. RGB or YP
BPRis selected
automatically depending on the
synchronising signal status.
When 480i, 576i, 480p, 576p, 
1 080/60i, 1 080/50i, 720/60p and
some VGA480 signals are being
input, select “RGB” or “YP
BPR” in
accordance with the input signal.
VGA60/480p
Set to “VGA60” when 59.9Hz
VGA480 signals are being input
(refer to page 62 for details). Set to...

ENGLISH-47
Adjustments and settings
DESK/CEILING
This setting should be changed in
accordance with the projector 
setting-up method. 
(Refer to page 18.)
DESK
When the projector is placed on a
desk or similar.
CEILING
When the projector is suspended
from a ceiling using the ceiling
bracket (sold separately).
FAN CONTROL
Set “FAN CONTROL” to “HIGH”,
when using this projector at high
elevations (above 1 400 m) only.
LAMP POWER
This setting changes the lamp
brightness. When set to “LOW”, the
luminance of...

48-ENGLISH
CONTROL KEY
To disable the buttons on the
projector, set “CONTROL KEY” to
“OFF”. A confirmation screen will
then be displayed. Select “OK” by
using Ior Hbutton. To use the
buttons on the projector, set to “ON”
by using the remote control unit. 
AUTO POW.OFF
If no signal is input to the projector
for the duration of the period you
set, the projector will return to
standby mode. The period can be
set from 15 minutes to 60 minutes
in 5 minute intervals. If you don’t
use this feature, set it to...

ENGLISH-49
Adjustments and settings
Setting up the security function
This projector is equipped with a security function. A password input screen
can be displayed, or a company URL can be set up and displayed at the
bottom of the projected image.
Press the For Gbutton on the
projector or remote control unit to
select “SECURITY”, then press the
ENTER button.
       MENU
KEYSTONE
PICTURE
POSITION
INDEX WINDOW
SHUTTER
VOLUME
LANGUAGE
OPTION
SECURITY
NETWORK
SELECT
  ENTER  EXIT
PASSWORD
   OK...

50-ENGLISH
TEXT DISPLAY
You can set text to be displayed at
the bottom of the projected image at
all times.
ON
“TEXT DISPLAY” is enabled.
OFF
“TEXT DISPLAY” is disabled.
TEXT CHANGE
The text which is displayed when
“TEXT DISPLAY” is set to “ON” can
be changed.
Press the ENTER button to display
the “TEXT CHANGE” screen.
#Press the F, G, Iand H
buttons to select the characters,
then press the ENTER button.
(You can enter 22 characters
continuously.)
CSelect “BS” to delete a
character.
$Press the F, G, Iand...