Panasonic Projector Pt L780ntu Specifications

11
Preparation
Slot cover (for projector LAN card)
(TKKL5243 x1)
(PT-L780NTU only)
Remote control unit
(N2QAEA000011 x1)
Power coed
(K2CG3FZ00008 x 1) AAA batteries for
remote control unit (x2)RGB signal cable [3.0 m
(9´10˝), K1HB15FA0001
x1]
Video/Audio cable [3.0
m (9´10˝),
K2KA2FA00001 x 1]
Accessories
Check that all of the accessories shown below have been included with your
projector.
CD-ROM (TQBH9003x1)
(PT-L780NTU only)
Protective case for SD memory card
(RP-SDCC0 x1)
(PT-L780NTU only)
Cable...

12
Precautions on handling
Cautions when moving the projector
Be sure to attach the lens cover before moving the projector.
The projection lens is extremely susceptible to vibration and shocks. Be\
careful not to subject it to excessive vibration and shock when moving t\
he
projector.
Cautions regarding setting-up
Observe the following at all times when setting up the projector.
Avoid setting up in places which are subject to vibration or shocks.
If the projector is set up in locations with strong...

13
Preparation
About the screen
If the screen you are using is dirty, damaged or discolored, attractive
projections cannot be obtained. Do not apply any volatile substances to the
screen, and do not let it become dirty or damaged.
About the lamp
The lamp may need to be replaced earlier due to variables such as a
particular lamp’s characteristics, usage conditions and the installation
environment, especially when it is subjected to a continuous use for more
than 10 hours.
About the SD memory card...

14
Location and function of each part
#Projector control panel
(page  16)
$ Focus ring
(pages  31 and  50)
% Air inlet ports
Do not cover these ports.
& Leg adjuster buttons(L/R)
(page  30)
These buttons are used to unlock
the front adjustable legs. Press to
adjust the angle of tilt of the
projector.
' Front adjustable legs(L/R)
(page  30)
( Lens release button
(page  51)
This button is used when using a
projection lens that is sold
separately.
) Projection lens
\b Lens cover
+ Remote control signal...

15
Preparation
#Remote control signal receptor
(page  22)
$ Security lock
This can be used to connect a
commercially-available theft-
prevention cable (manufactured
by Kensington). This security lock
is compatible with the Microsaver
Security System from
Kensington. Contact details for
this company are given below.
Kensington Technology Group
ACCO Brands Inc.
2855 Campus Drive
San Mateo, CA 94403 USA
Tel (650)572-2700
Fax (650)572-9675
http://www.kensington.com/
http://www.gravis.com/
NOTE:
B Information...

16
Remote control unit
#Power indicator
(pages  30, 31  and  47)
This indicator illuminates red when
the MAIN POWER switch is turned
on (standby mode), and illuminates
green when the power is turned on
and a picture starts to be projected.
(PT-L780NTU only)
When the WEB STANDBY is set
to ON, the cooling fan operates
and the power indicator on the
projector flashes slowly in red.
$ RGB INPUT indicator
This indicator illuminates when a
signal is input into the connector
that is selected with the input...

17
Preparation
properly when using a lens that is
sold separately. Refer to page 42
for details on correcting keystone
distortion manually.
\b SHUTTER button  (page 46)
This button is used to
momentarily turn off the picture
and sound. However, keystone
distortion may not be corrected
properly when using a lens that is
sold separately. Refer to page  42
for details on correcting keystone
distortion manually.
+ MENU button  (pages 32 and  35)
This button is used to display the
menu screens. When a menu...

18

USBDVI-D IN
REMOTE SERIAL
RGB1 IN
RGB2 IN/RGB OUT AUDIO OUT
RGB AUDIO IN VIDEO INAUDIO IN
S-VIDEO IN
RL
R/R-Y/P
RVDSYNC/HDB/B-Y/PBRGB3 IN
G/Y
'&()
%$#
,-\f+ \b
#
USB port
(page  21)
The remote control unit can be
used as 
a personal computer
mouse by connecting the
projector to 
a personal computer
with the supplied USB cable.
(4-pin square connector)
$ SERIAL connector
(pages  26, 27  and  58)
This connector is used to connect
a personal computer to the
projector in order to externally
control...

LOCK
)
(
19
Preparation
'%&
$
#

Front Back
# Slot cover
Covers the card slots. When
using an optional projector LAN
card, replace the slot cover (refer
to page  54).
$ Card slot
Insert an optional wireless card or
a projector LAN card into here.
% Eject switch
Use to remove an optional
wireless card or projector LAN
card from the card slot.
& Access lamp
Flashes while the projector is
being accessed for reading or
writing the data in the SD
memory card. '
SD memory card slot
Insert the SD memory...

20
Using the remote control unit
PUSH
Laser beam pointer
The laser beam emitted from the remote control can be used as a pointer by
pointing forward to the screen.
While the LASER button is being pressed, the laser beam is being emitted
and the operating indicator illuminates.
Do not look into the laser emitter of the remote control unit or point the laser
beam towards other people, otherwise damage to eyes may occur.
Caution
BUse of controls or adjustments or performance of procedures
other than those...