Panasonic Projector Pt L735ntu Operating Instructions

ENGLISH-21
Getting started
Example of connecting to computer
NOTE:
BIt is better to shut down the computer before turning off the MAIN
POWER switch of the projector.
BDo not input the signal to the RGB2 IN/RGB1 OUT connector when the
RGB2 SELECT item in the OPTION menu is set to “OUTPUT”. (Refer
to page 45.)
162345 ON DIP
D-sub 9-pin
(male) Computer for
control useComputer
Monitor
Audio system
Refer to the accessory CD-ROM for details on the wireless network
that is used for controlling the projector...

22-ENGLISH
Operating range
If the remote control unit is held so that it is facing directly in front of the
remote control signal receptors on the front or rear of the projector, the
operating range is within approximately 7 m (23´) from the surfaces of the
receptors. Furthermore, the remote control unit can be operated from an
angle of ±30° to the left or right and ±15° above or below the receptors. #Open the cover.
AAA batteries
(two) $Insert the batteries so that the 
polarities are correct, and then...

ENGLISH-23
Basic Operation
Turning on the power
Before turning on the power
1, Ensure that all components
are connected properly.
2, 
Connect the accessory power cord.
3, Remove the lens cover.
Press the MAIN POWER switch to turn on the
power.
BThe power indicator on the projector will illuminate red.
Press the POWER button.
BThe power indicator on the projector will flash green. After a short
period, the indicator will illuminate green, and a picture will be
projected.
Turn on the power of all connected...

24-ENGLISH
Press the input select button to select the
input signal.
BA picture will be projected in accordance with the selected input signal.
Follow the procedure below when you set the projector up first, and when
you change the setup place.
Press the AUTO SETUP button to initiate
automatic positioning.
BThe tilt of the projector and the input
signal will be detected and keystone
distortion and the position of the
image will be corrected.
(Refer to page 27 for details.)
Adjusting the size
BTurn the...

ENGLISH-25
Basic Operation
Turning off the power
Press the POWER button.
B“Power OFF” is displayed on the
screen.
Select “OK” using the I I
and H H
buttons and
then press the ENTER button.
BThe lamp unit will switch off and the picture will stop being projected.
(The power indicator on the projector will illuminate orange.)
#
$
%
AUTO SETUP
LASER
MENU VIDEO
PAGE
ENTER
R-CLICK
RGB POWER
#
$
%
RGB input indicator Power indicator
Power OFF
OKCANCEL
Press the MAIN POWER switch to turn off the
power after the...

26-ENGLISH
Power indicator
Power indicator status
Red
IlluminatedThe projector is in standby mode and image projection
is possible by pressing the POWER button.
A picture is being projected.
The lamp is cooling down after the power is turned
off. (The cooling fan is operating.)
The projector is preparing for projection after the
power is turned on while the power indicator is
illuminated orange. (After a short period, a picture
will be projected.) The projector is preparing for projection after the
power...

ENGLISH-27
Correcting keystone distortion and
automatic positioning (AUTO SETUP)
This projector detects its degree of tilt and the input signal. Keystone distortion and the
position of the image can then be corrected automatically in accordance with the input signal.
Projector control panelPress the AUTO SETUP button.
(When the projected image has caused keystone distortion)
BAutomatic positioning
will be carried out.
Screen
Projected
image
If you press the AUTO SETUP button, the items given in the table...

28-ENGLISH
Turning off the picture and sound
momentarily (SHUTTER)
The shutter function can be used to momentarily turn off the picture and
sound from the projector when the projector is not being used for short
periods of time, such as during breaks in meetings or when carrying out
preparation. The projector uses less power in shutter mode than it does in
normal projection mode.
Still picture
BThe picture being projected will be paused.
BPress the FREEZE button again to cancel the
still picture. Press...

ENGLISH-29
Useful functions
BThe picture will then
be enlarged to 1.5
times the normal size.
The remote control unit functions during D.ZOOM (digital zoom)
Use the F,G,IandHbuttons to move the enlarged area which you want to project.
Use the D.ZOOM +/- buttons to change the enlargement ratio.
Press the MENU button to return to the normal screen.
[
Enlarging the picture (D.ZOOM)
Adjusting the volume (VOLUME)
Press a D.ZOOM +/- button.
Press the VOLUME +/- button.
BPress the + button to raise the volume....

30-ENGLISH
Useful functions of the remote control unit
Laser beam pointer
The laser beam emitted from the remote control can be used as a pointer by
pointing forward to the screen.
While the LASER button is being pressed, the laser beam is being emitted
and the operating indicator illuminates.
Do not look into the laser emitter of the remote control unit or point the laser
beam towards other people, otherwise damage to eyes may occur.
Caution
BUse of controls or adjustments or performance of procedures...