Panasonic Projector Pt Ex12ku Operating Instructions

About your projector
ENGLISH - 21
Preparation
(1)Lens hood
(2) Lens (optional)
(3) Indicator (
 page 87)
(4) Remote control sensor (front)
(5) Adjustable feet
Adjusts the projection angle. (
 page 35)
(6) Connection terminals (
 page 23)
(7) Carry handle
(8) Control panel (
 page 22)
(9) Lamp cover
Houses the lamp unit. (
 page 97) (10)
Remote control sensor (rear)
(11) Air exhaust port
(12) Main power switch
Turns off/on the main power.
(13) AC input terminal
Connect the supplied power cord. (
...

About your projector
22 - ENGLISH
Preparation
■
■ Control panel
(1)
(2)
(3)
(4)
(5)
(6)
(7) (8)
(9)
(10)
(11)
(6)
(12)
(1)
Power  button
Turns off/on the power when the main power switch on the 
projector is set to 
.
(2)  button
Opens and closes the shutter. Adjusts the shielding of the 
projection light. (
 page 47)
(3)  button
Adjusts the zoom of the lens. (
 page 46)
(4)  button
Adjusts the focus. (
 page 46)
(5)  button
Displays the menu screen. (
 page 50)
(6) ▲▼◀▶  buttons
Move the cursor on...

About your projector
ENGLISH - 23
Preparation
■
■ Connection terminals
(1)
(2)(3) (4) (10) (9) (8) (7) (6) (5)
(1)
DVI-D input terminal 
This terminal is for inputting the DVI-D signal.
(2) HDMI input terminal 
This terminal is for inputting the HDMI signal.
(3) Computer input terminal 
This terminal is for inputting an RGB signal.
(4) RGB 5BNC input terminal //
This terminal is for inputting the G,B,R,H/HV,V signal, 
video signal, and Y,Pb/Cb,Pr/Cr signal.
(5) USB terminal 
This terminal is for use by...

Using the remote control
24 - ENGLISH
Preparation
Using the remote control
Inserting and removing the batteries
1) Open the cover.
(ii)(i)
2) Insert the batteries and close the 
cover.
■
z Insert the  side first.
■
z To remove the batteries, perform the above 
procedure in the reverse order.
Setting remote control numbers
When you are using multiple projectors, you can set a remote control number to each projector to allow 
simultaneous control with a single remote control.
After setting a remote control...

Attaching the lens
ENGLISH - 25
Getting Started
Attaching the lens
Notes on attaching the lens
Before putting the projector in position, attach the lens to the projector body.
First, determine the lens according to the operating environment for the projector .
For lens product numbers suitable for the projector and lens specifications, consult your dealer . When attaching 
or replacing a lens, consult the technical staff or service personnel at a specialist dealer for safety. Do not attempt 
to attach or...

Attaching the lens
26 - ENGLISH
Getting Started
Attaching the lens
Attention■
z The attachment procedure and parts vary depending on the optional lens. Check the product No. and attach 
the lens properly.
■
z When using ET-ELW02, ET-ELS02, ET-ELS03, ET-ELT02, or ET-ELM01, tie up the cables using the cable 
ties supplied with the projector before attaching the lens. If you attach the lens without tying up the cables, the 
cables may contact the internal parts, causing malfunctions.
1) 
Install the lens...

Attaching the lens
ENGLISH - 27
Getting Started
6) Select the light-shielding plate to be 
attached.
 
z Light-shielding plate for each lens
Refer to the following table and use an appropriate 
light-shielding plate.
Accessory (product name)
Lens Model No.
Light-shielding plate-1
(T0CRS0008--1) ET-ELW03
*1
Light-shielding plate-2
(T0CRM0014--1)ET-ELW04, 
ET-ELW06, 
ET-ELS02, 
ET-ELS03, 
ET-ELT03
 is inscribed
Light-shielding plate-3
(T0CRM0013--1)ET-ELW02, 
ET-ELW03*1, 
ET-ELT02, 
ET-ELM01
 is inscribed...

Attaching the lens
28 - ENGLISH
Getting Started
10) Secure the lens lock lever with the 
lens lock lever fixing bracket.
(i) Remove the lens fixing screw and insert it to 
the lens lock lever fixing bracket.
(T0STF0045--)
Lens lock leve\fSc\few
Lens lock leve\f fi\bin\vg b\facket (T
ype SC-A)
(ii) Mount the lens lock lever fixing bracket in the 
location of the removed screw.
•■Make sure that the lens lock lever fixing 
bracket is mounted to keep the lens lock 
lever in the lock position. Confirm that...

Attaching the lens
ENGLISH - 29
Getting Started
13) Turn the lens hood clockwise to 
attach.
■
z Aligning the point position of the lens hood 
with the end (on the left) of the caution label 
attached to the projector body, turn the lens 
hood while pushing it until it clicks to overlap 
with the point position of the projector body.
&DXWLRQODEHO
3RLQWSRVLWLRQRIWKHSURMHFWRUERG\
0DNHVXUHWRDOLJQWKHSRLQW
SRVLWLRQRIWKHOHQVKRRG
/HQVKRRG
Attention
■
z Confirm that the lens hood is attached...

Attaching the lens
30 - ENGLISH
Getting Started
■
■ ET-ELW03
1) 
Loosen the focus lock screw.
2)  Rotate the lens to obtain the proper 
focus on the center area of the screen.
■
z When the distance between the projector and 
the screen is 1 m (39"), set the position of the 
focus lock screw to the 
● mark (yellow allow) of 
the lens.
3)  Tighten the focus lock screw.
4)  If the proper focus is not observed 
on outer area of the screen, proceed 
further adjustment.
(i)  Turn the focus ring...