Panasonic Projector PT-EW730Z User Manual

Chapter 1 Preparation — Precautions for use
ENGLISH - 21
 
r LCD panel
 
f The LCD panel is precision-made. Note that in rare cases, pixels of high precision could be missing or always lit. Note that 
such phenomena do not indicate malfunction. If still images are projected for a long time, a residual image may remain on 
the LCD panel. Note that the residual image may not disappear.
 
r Optical parts
When the operating environment temperature is high or in environments wh\
ere lots of dust, cigarette...

Chapter 1 Preparation — Precautions for use
22 - ENGLISH
Accessories
Make sure that the following accessories are provided with your projector. Numbers enclosed in <  > show the number of 
accessories.
Wireless/wired remote control unit 
(N2QAYA000063)
Power cord
(TXFSX01RXQZ)
(TXFSX01RWDZ)
(TXFSX01RXRZ)
(TXFSX02UTRZ)
Lens hole cover 
(Only lens optional models)
(Attached to the projector at the time of purchase)
(6103619194)
Lens cover 
(Only models with lens)
(6103626291)
CD-ROM 
(TXFQB02VLM8)
AAA/R03...

Chapter 1 Preparation — Precautions for use
ENGLISH - 23
SoftwareMulti Projector Monitoring & 
Control Software (Windows)This software allows you to monitor and control multiple 
projectors connected to the LAN.
Logo Transfer Software 
(Windows) This software allows you to transfer original images, such as 
company logos to be displayed when projection starts, to the 
projector.
Optional accessories
Optional accessories 
(product name) Model No.
Projection Lens Zoom lens
ET-ELW20, ET -ELT20, ET-ELT21...

Chapter 1 Preparation — Start-up display
24 - ENGLISH
Start-up display
When the projector is switched on for the first time after purchase as well as when [ALL USER DATA] in the [PROJECTOR SETUP] menu → 
[INITIALIZE] is executed, the focus adjustment screen is displayed after projection starts, then the initial setting screen is displayed. Set them 
in accordance with circumstances.
In other occasions, you can change the settings by menu operations.
Focus adjustment
Adjust the focus to display the menu...

Chapter 1 Preparation — Start-up display
ENGLISH - 25
Initial setting (standby mode)
Set the operation mode during standby. The default setting is [ECO] that keeps power consumption low during standby. When the network 
function is used during standby, set to [NORMAL]. After completed the initial setting, you can change the setting from the [PROJECTOR 
SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE].
1) Press qw to switch the setting.
3/4
ENTERSET CHANGE
If STANDBY MODE is set to ECO, you cannot use...

Chapter 1 Preparation — About your projector
26 - ENGLISH
About your projector
Remote control
1
3 2
4
5
8 7 6 6
9
10 16
17
18
19 15
11 13
20
22 21
24 23
12
14 25
26
Front To p
Bottom
1 Power standby  button
Sets the projector to the state where the projector is switched 
off (standby mode) when the  switch on the 
projector is set to  and in the projection mode.
2  Power on < b> button
Starts projection when the  switch on the 
projector is set to  when the power is switched off 
(standby mode).
3...

Chapter 1 Preparation — About your projector
ENGLISH - 27
 
f Avoid contact with liquids or moisture.
 
f Do not attempt to modify or disassemble the remote control.
Note
 
f When operating the remote control by directly pointing the remote contro\
l signal receiver of the projector, operate the remote control at 
a distance approx. 30 m (98'5") or shorter from the remote control signal receiver. The remote control can control at angles of up to ±30° 
vertically and horizontally, but the...

Chapter 1 Preparation — About your projector
28 - ENGLISH
202118 19
Projection direction
Bottom
To p
18 Burglar hook port
Attaches a burglar prevention cable, etc.
19  Luminance sensor (x page 68) 20 
Lens release button
21  Lamp cover
The lamp unit is inside.
Attention
 
f Do not block the ventilation ports (intake and exhaust) of the projector .
 
r Control panel
7 3 5
6
8
1
2
3
4
1 
Power standby  button
Sets the projector to the state where the projector is switched 
off (standby mode) when the...

Chapter 1 Preparation — About your projector
ENGLISH - 29
 
r Connecting terminals
1 234 5 678
9 11
10 1213
1  terminal
This is the LAN terminal to connect to the network. This is also 
used when connecting a device for transmitting video and audio 
signals via the LAN terminal.
2   terminal
This is the terminal to input HDMI signals.
3   terminal
This is the terminal to connect to the remote control by cable 
when controlling the projector by wired remote control.
4   terminal
This is the terminal to...

Chapter 1 Preparation — Using the remote control
30 - ENGLISH
Using the remote control
Inserting and removing the batteries
(ii)(i)
Fig. 1Fig. 2
1) Open the cover. (Fig. 1)
2)  Insert the batteries and close the cover (insert the m side first). (Fig. 2)
 
f When removing the batteries, perform the steps in reverse order.
Setting the ID number of the remote control
When you use the system with multiple projectors, you can operate all th\
e projectors simultaneously or each projector individually using...