Panasonic Projector PT-DZ16K Specifications

							List of compatible  signals
The  signals  that  can  be input  to  this  projector  ar e shown  in  the  table  below . Horizontal  scanning  fre-
quencies  of  15  kHz  to  100 kHz,  vertical  scanning  fr equencies  of  24Hz  to  120 Hz,  and  a dot  clock  of
162  MHz  maximum  can  be  input .
NOTE: The  native  resolution  of  this  projector is 1,920×  1,080 pixels.  If  the display  resolution  of  the input  signal  is  differe nt from  the
native  resolution,  image compression  or  expansion  will  be  used  to  convert  the input signal  to  a level  within  the  native  resolu tion.
Display mode Display
resolution
(dots)*
1
Scanning frequency
H
(kHz) V
(kHz)Dot clock
frequency
(MHz) Format
720 × 480i
720 × 576i
720 × 480i
720 × 576i
720 × 483
720 × 576
1280 × 720
1920 × 1080 i
1280 × 720
1920 × 1080 i
1920 × 1080
1920 × 1080 i
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
640 × 400
640 × 480
800 × 600
832 × 624
1024 × 768
1152 × 864
1152 × 870 1
5.7
1 5.6
1 5.7
1 5.6
3 1.5
3 1.3
4 5.0
3 7.5
3 3.8
2 8.1
2 7.0
2 7.0
2 8.1
3 3.8
6 7.5
5 6.3
3 1.5
3 7.9
3 1.5
3 5.0
3 7.9
3 7.5
4 3.3
3 5.2
3 7.9
4 8.1
4 6.9
5 3.7
4 9.7
3 9.6
4 8.4
5 6.5
6 0.0
6 5.5
6 8.7
8 1.4
9 8.8
5 3.7
6 4.0
6 7.5
77.1
6 8.7 59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
24.0
48.0
25.0
30.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.0
60.0
70.1
75.0
81.6
85.0
100.0
120.0 60.0
70.0
74.9
85.0
75.1 

13.5
1 5.7
1 5.6 59.9
50.0 27.0
7
4. 3
148.5 25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
86.0
94.5
113.3
139.1 81.6
94.2
108.0
119.7
100.0
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
480i (525i)
576i (625i)
720(1440) × 480
480i (525i)
576i (625i)
480p (525p)
576p (625p)
720/60p
720/50p
1080/60i
1080/50i
1080/24p
1080/24sF
1080/25p
1080/30p
1080/60p
1080/50p
V
ESA400
VGA480
SVGA
MAC16
XGA
MXGA
MAC21 V
IDEO/
Y/C(RGB1)
SDI/RGB1/R GB2
HDMI/DVI-D
SDI/ HDMI/DVI-D/
RGB1/RGB2
HDMI/DVI-D/RGB1/
RGB2  HDMI/DVI-D/RGB1/
RGB2 
* 1
* 2W
hen 1125(1035)/60i signal input, it displays as 1125(1080)/60i signa\
ls. 
Pixel-Repetition signal(dot clock frequency 27.0MHz) only.
  .
*1
720(1440) × 480*1
*2
As of April 2014
11/14
PT-DZ16K3-Chip DLP™ Projector 
SFD14M020  
						

							Display modeDisplay
resolution
(dots)Scanning frequency
H
(kHz) V
(kHz)Dot clock
frequency
(MHz) Format
1280 × 720
1280 × 768
1280 × 768
1280 × 768
1280 × 800
1280 × 800
1280 × 800
1280 × 960
1280 × 1024
1366 × 768
1400 × 1050
1440 × 900
1600 × 1200
1680 × 1050
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1200
1920 × 1200
1920 × 1200 3
7.1
4 4.8
7 6.3
9 2.6
3 9.6
4 7.8
4 7.4
6 0.3
6 8.6
4 1.3
4 9.7
4 9.3
6 2.8
7 1.6
6 0.0
5 2.4
6 4.0
7 2.3
7 8.2
8 0.0
9 1.1
4 7.7
3 9.6
5 4.1
6 4.0
6 5.2
6 5.3
7 8.8
8 2.2
5 5.9
4 6.3
7 5.0
6 5.3
5 4.1
5 5.6
6 6.6
6 7.2
6 1.8
7 4.0
7 4.6 49.8
59.9
100.0
120.0 49.9
59.9
60.0
74.9
84.8
50.0
59.8
59.9
74.9
84.9
60.0
50.0
60.0
66.3
72.0
75.0
85.0
59.8
49.9
50.0
60.0
60.0
60.0
72.0
75.0
59.9
49.9
60.0
60.0
50.0
49.9
59.9
60.0
49.9
60.0
59.9 60.5
74.5
131.8
161.6 65.3
79.5
68.3
102.3
117.5
68.0
83.5
71.0
106.5
122.5
108.0 88.0
108.0
125.0
135.1
135.0
157.5
85.5
69.0
99.9
108.0
122.6
121.8
149.3
155.9
106.5
86.8
162.0
146.3
119.5
141.5
138.5
173.0
158.3
154.0
193.3
1280 × 72
0
1280 × 76 8
1280 × 80 0
MSXGA
SXGA
1366×768
SXGA+
WXGA+
UXGA
WSXGA 1600 × 900
4
6.4
5 5.9 49.9
60.0 96.5
119.0
1600×900
+
1920×1080
WUXGA HDMI/DVI-D/R
GB1
RGB2
RGB 1/RGB2
HDMI/DVI-D/R GB1/
RGB2
RGB 1/RGB2
*
3
*3
*3
*3
*
Compliant 
with  VESA  CVT-RB  (Coor dinated  Video  Timing-Reduced  Blanking).
*4
*4
3
* Image resolution is reduced by the image processing circuit before proje\
ction.4
As of April 2014
12/14
PT-DZ16K3-Chip DLP
						

							500 mm  (1  ft  8 in ) or  more 500 mm  (1  ft  8  in) 
or  more 50
0 mm  (1  ft  8 in ) 
or  more
Do not stack pr ojector 
units dire ctly on top of 
one another.
10
0 mm
(3 -15/ 16  in ) 
or  more
N otes  on projector  placement  and  operation 
The  projector  uses  a  high-wattage  lamp  that becomes  very  hot  during  operation.  Please observe  the
following  precautions .
1. Never  place objects  on  top  of  the  projector  while  it  is  operating.
2. Make  sure the re is  an  unobstructed  space  of  500  mm  (1 feet  8  inches)  or  more around  the  projec -
tor’s  exhaust  openings.
3. Do  not  stack  projector  units  directly  on  top  of  one  anothe r. If  two  units  must  be  stacked for back-
up  use  in  or dinary  projection,  use  a method  as  shown below  and  provide  ample  space  between the
units  to  ensu re that  exhaust  heat  does not  accumulate  near the  intake  opening  or  around the  units.
D ual  stacked  projection  is  not  recommended.
4. Make  sure that  nothing  blocks the projector’s  air intake  and exhaust  openings.  Also,  install  the  pro-
jector  so  that  cool  or  hot  air from  other  air  conditioning  equipment  does not  flow  dire ctly  toward  the
pr ojector ’s air  intake  or  exhaust  openings.
5. Do  not  install  the  projector  in  an  enclosed  space.  If  it  is  necessary  to  install  it  in  an  enclosed
s pace,  add  a  separate  ventilation  system.  If ventilation  is  insufficient,  hot  air will  accumulate  at  the
intake  opening.  This  may  cause  the  projector’s  protective  circuit  to  interrupt  projector  operation.
6. If the  projector  is  installed  in  an enclosed  space,  ensure that  the  temperatur e  of  the  air  surrounding
the  projector  is  between  0° Cand 40°C( 32°Fand  104°F).  Also  make sure that  the  projector’s  intake
and  exhaust  openings  are  not  blocked.  Even  though  the  air  surr ounding  the  projector  is  40°
 C
( 104°F )or less,  if  hot  exhaust  air accumulates  inside  the  space,  it  may cause  the  projector’s  protec -
tive  circuit  to  interrupt  projector  operation.  Pay  particular  attention  to  the  surrounding  temperatur e
conditions  when planning  the  installation.
7. If the  projector  is  not  to  be set  on  the  floor  using  adjuster  legs,  install  it  by using  the  five  ceiling-
m ount  sc rew  holes  (screw  diameter:  M6, length  of  each screw  hole  in  the  projector:  30  mm (1-3/16
inches)).  Pr ovide  a space  of  5  mm  (3/16 inches)  or  more b etween  the  projector  and  the  mountin g
surface  by inserting  metal spacers.
As of April 2014 13/14
PT-DZ16K3-Chip DLP™ Projector 
SFD14M020  
						

							Operating the  projector  continuousl y
1.  If  the  projector  is  to  be  operated  continuously  one  week,  use  the  quad-lamp  optical  system ’s alternating
lamp  operation  (lamp  relay)  function.  The  pr ojector  cannot  be  operated  continuously  one  week  in  quad -
lamp  mode.  Allow  a  minimum  of  two  hours  per  day  of  non-operation  time  for  each  lamp  if  the  projecto r
is  to  be  operated  continuously  for  mo re than  one  week.
2.  The  lamp  replacement  cycle  duration  becomes  shorter  if  the  projector  is  operated  repeatedly  for  shor t
periods.
We ights  and dimensions  shown  are approximate.  Specifications  and  appearance  are  subject  to change  without  notice.
Pr oduct  availability  dif fers depending  on  region  and country . This  product  may  be  subject  to  export  control  regulations.
DLP  and  the  DLP  logo are  trademarks  of Texas  Instruments.  
PJLink  is  a register ed trademark,  or a  trademark  application  has  been  filed,  in  Japan,  the United  States,  and  other countries  and  regions.  
All  other  trademarks  are  the  property  of  their  respective  trademark  owners.
Direction  of  air intake  and  exhaust
Intake
Exhaust
As of April 2014 14/14
PT-DZ16K3-Chip DLP