Panasonic Projector PT-DX610UL User Manual

ENGLISH - 101
Chapter 4 Settings  —   [NETWORK] menu
[E-mail set up] page
You can send E-mail to an E-mail address (maximum two addresses) set in advance when a problem occurs or the cumulative operating time 
of a lamp reaches a set value.
Click [Detailed set up]
 → [E-mail set up].
(1)
(2)
(3)
(4)
(5)
(6)
1 [ENABLE]
Select [Enable] to use the E-mail function.
2
 
[SMTP
  SERVER NAME]
Enter the IP address or the server name of the E-mail server 
(SMTP). To enter the server name, the setup of the DNS...

102 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
(11)
(10)
(9)
9 [E-MAIL ADDRESS 2]
Enter the E-mail address to be sent when two E-mail addresses 
are to be used.
Leave it blank when two E-mail addresses are not to be used.
10
 
Settings of the conditions to send E-mail
Select the conditions to send E-mail to the second E-mail 
address.
[MAIL

 CONTENTS]:
Select either [NORMAL] or [SIMPLE].
[ERROR]:
An E-mail message is sent when an error occurred in the self-
diagnosis.
[LAMP1 RUNTIME]:
An E-mail...

ENGLISH - 103
Chapter 4 Settings  —   [NETWORK] menu
Contents of mail sent
Example of E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been established.
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : DW640
Serial No               : SH1234567
-----  E-mail setup data -----
TEMPERATURE WARNING SETUP 
MINIMUM TIME           at [ 60] minutes interval 
INTAKE AIR TEMPERATURE Over [ 45 degC / 113 degF ] 
ERROR                   [ OFF ] 
LAMP1...

104 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
Example of the E-mail sent for an error
The following E-mail is sent when an error has occurred.
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : DW640
Serial No               : SH1234567
-----  check system -----
MAIN CPU BUS   [   OK   ]
FAN   [   OK   ]
INTAKE AIR TEMPERATURE   [   OK   ]
OPTICS MODULE TEMPERATURE   [   OK   ]
AROUND LAMP TEMPERATURE   [   OK   ]
LAMP1 REMAIN TIME   [   OK   ]
LAMP2 REMAIN TIME   [   OK   ]...

ENGLISH - 105
Chapter 4 Settings  —   [NETWORK] menu
[Administrator] account
(1)
(2)
(3)
(4)
(5)
(6)
(7)
1 [Account]
Displays the account to change.
2
 
[Current][User name]
Enter the user name before the change.
3

 
[Current][Password]
Enter the current password.
4

 
[New][User name]
Enter the desired new user name. (Up to 16 characters in single 
byte) 5

 [New][Password]
Enter the desired new password. (Up to 16 characters in single 
byte)
6
 
[New][Password(Retype)]
Enter the desired new password...

106 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
[Change password] (For user rights)
Only the change of password is enabled under the user rights.
(1)
(2)
(4) (3)
1 [Old Password]
Enter the current password.
2
 
[New Password]
Enter the desired new password. (Up to 16 characters in single 
byte) 3

 [Retype]
Enter the desired new password again.
4
 
[OK]
Determines the change of password.
Note
rfTo change the account of the administrator, you must enter the [Current] [User name] and [Password]....

ENGLISH - 107
Chapter 4 Settings  —   [NETWORK] menu
[Tools] page
Click [Tools] on the control page.
1
2
3
4
5
1 [Control System]
Set the information required for communicating with the 
controller to be connected with the projector
.
2
 
[User Password]
Set the user rights password for the RoomV

iew control page.
3
 
[Admin Password]
Set the administrator rights password for the RoomV

iew control 
page.
4
 
Network Status
Displays the settings of wired LAN. [DHCP]
Displays the current setting.
[Ip...

108 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
[Help] page
Click [Help] on the control page.
The [Help Desk] window is displayed.
1
1 [Help Desk]
Messages can be sent to or received from an administrator who 
uses Crestron RoomV
iew.  

ENGLISH - 109
Chapter 5 Maintenance
This chapter describes inspection when there are problems, and maintenance methods.  

110 - ENGLISH
Chapter 5 Maintenance  —   Lamp/Temperature/Filter indicators
Lamp/Temperature/Filter indicators
Managing the indicated problems
If a problem should occur inside the projector, the lamp indicators // the temperature indicator  and the filter 
indicator  will inform you by lighting or flashing.
Check the status of the indicators and manage the indicated problems as follows.
Attention
rfWhen switching of f the projector to deal with problems, make sure to follow the procedure in “Switching...