Panasonic Projector Pt Dw730ul Operating Instructions

							[SECURITY] menu 
ENGLISH - 71
Settings
Note 
z
The logo is displayed on the whole screen in 
the normal projection condition when [DEFAULT 
LOGO] is set. Since the menu screen is displayed, 
it is not possible to see the whole image even if the 
logo display is canceled by pressing the  
button. 
 
z
Separate software   Logo Transfer Software¡  is 
re quired to create and register the pictures of [USER 
LOGO]. Refer to the application software  download 
f

rom the website support information  
(http://panasonic.net/avc/projector/software/).
[TEXT CHANGE]
You can change the text displayed  when the text display 
is enabled by selecting [TEXT] in [DISPLAY SETTING].
 
1)  Press ▲▼ to select [TEXT CHANGE]. 
2)  Press the  button. 
 
z
The [TEXT CHANGE] screen is displayed. 
3)  Press  ▲▼◀▶ to select the text, and press 
the  button to enter the t ext. 
 
z
Up to 22 characters can be entered.
4)  Press ▲▼◀▶ to select [OK] and 
press the  button. 
 
z
The text is changed.
[MENU LOCK]
You can set to enable/disable the menu operation by 
displaying the menu with the  button. 
1)  Press ▲▼ to select [MENU LOCK]. 
2)  Press ◀▶ to switch [MENU LOCK]. 
 
z
The setting will change as follows each time 
you press the button.
[OFF][ON]
[OFF]Releases the lock of the menu operation. 
[ON] Locks the menu operation. 
Note  
z
The  button operations will be disabled 
when an incorrect password is entered after setting 
[MENU LOCK] to [ON]. 
 
z
The password setting is set to [OFF] at the time of 
purchase or when [ALL USER DATA] is initialized. 
 
z
The unlock status is maintained until the projector 
is set to the standby mode.
[MENU LOCK PASSWORD]
You can change the MENU LOCK PASSWORD. 
1)  Press ▲▼ to select [MENU LOCK 
PASSWORD].
2)  Press the  button.
 
z
The [MENU LOCK PASSWORD] screen is 
displayed.
3)  Press ▲▼◀▶ to select the text, and press 
the  button to enter the text. 
 
z
Up to 16 characters can be entered.
4)  Press ▲▼◀▶ to select [OK] and 
press the  button. 
 
z
Select [CANCEL] to stop.
Attention  
z
The init ial password when used for the first time or 
a

fter initializing all the user data is  “
AAAA ”
. 
 
z
Change the pass word periodically that is hard to guess.
[CONTROL DEVICE SETUP]
You can enable/disable the button operations on the 
control panel and the remote control. 
1)  Press ▲▼ to select [CONTROL 
DEVICE SETUP]. 
2)  Press the  button. 
 
z
The [CONTROL DEVICE SETUP] screen is 
displayed. 
3)  Press ▲▼ to select [CONTROL PANEL]  
or [REMOTE CONTROLLER]. 
4)  Press the  button. 
 
z
The [CONTROL PANEL] or [REMOTE 
CONTROLLER] screen is displayed. 
 
■ [CONTROL PANEL]
 
z
You can set the limitation on the control from 
the control panel. 
[ENABLE] Enables the button operation from 
the main unit. 
[DISABLE] Disables the button operation from 
the main unit.  
						

							[SECURITY] menu 
72 - ENGLISH
Settings
 
■ [REMOTE CONTROLLER]
 
z
You can set the limitation on the control from 
the remote control. 
[ENABLE] Enables the button operation from 
the remote control. 
[DISABLE] Disables the button operation from 
the remote control. 
5)  Press ▲▼ to select [ENABLE] or 
[DISABLE], and press the  
button. 
6)  When the confirmation is displayed,  select [OK] or [CANCEL], and press 
the  button. 
Note
 
z
When a button operation is performed on the device 
set to [DISABLE], the [SECURITY PASSWORD] 
screen  is displayed. Enter the security password. 
 
z
The [SECURITY PASSWORD] screen will 
disappear when the  button is pressed or 
there is no operation for approximately ten seconds. 
 
z
The power cannot be turned off (the standby mode 
cannot be set) if the operations of both [CONTROL 
PANEL] and [REMOTE CONTROLLER] are set to 
[DISABLE].
 
 
z
When the setting has completed, the menu screen 
will disappear. To
 operate continuously, press the 
 button to display the main menu.  
						

							[NETWORK] menu 
ENGLISH - 73
Settings
[NETWORK] menu 
Select [NETWORK] from the main menu, and 
select the item from the sub-menu. 
Refer to “
Navigating through the menu ”
 
(
 page 41) regarding the operation of the menu 
screen.   
z
After selecting the item, press ÛÝ/¢/£ to set. 
[NETWORK SETUP]
Perform the initial setting of the network before using 
the network function. 
1)  Press ▲▼ to select [NETWORK 
SETUP]. 
2)  Press the  button. 
 
z
The [NETWORK SETUP] screen is displayed. 
3)  Press ▲▼ to select an item, and 
change the settings according to the 
operation instructions of the menu. 
[PROJECTOR 
NAME] Change the setting when using a 
DHCP server. 
[DHCP] Set this to [ON] when using a 
DHCP server to acquire the IP 
address automatically. Set to [OFF] 
when not using a DHCP server.
[IP ADDRESS]  Enter the IP address when not 
using a DHCP server. 
[SUBNET 
MASK] Enter the subnet mask when not 
using a DHCP server. 
[DEFAULT 
GATEWAY] Enter the default gateway address 
when not using a DHCP serv
er.
 
[STORE] Save the current network settings. 
4)  Press ▲▼ to select [STORE], and 
press the  button. 
5)  When the confirmation is displayed,  select [OK] or [CANCEL], and press 
the  button.
Note
 
z
When using a DHCP server, confirm that the DHCP 
server is running. 
 
z
Consult your network administrator regarding the IP 
address, subnet mask, and default gateway. 
[NETWORK CONTROL]
You can set up the control method of the network. 
1)  Press ▲▼ to select [NETWORK 
CONTROL]. 
2)  Press the  button. 
 
z
The [NETWORK CONTROL] screen is 
displayed. 
3)  Press ▲▼ to select an item, and press 
◀▶ to ch ange the setting. 
[WEB 
CONTROL] Set to [ON] to control with the Web 
browser. 
[PJLink 
CONTROL] Set to [ON] to control with the 
PJLink protocol. 
[COMMAND  CONTROL] Set to [ON] to control with the 
/ 
terminal control command format 
(
 page 99). 
Refer to  “
Control commands via 
LAN ”
 (
 page 96). 
[COMMAND  PORT] Set the port number used for 
command control. 
[STORE] Save the current network control 
settings.
 
4)  Press ▲▼ to select [STORE], and 
press the  button. 
5)  When the confirmation is displayed,  select [OK] or [CANCEL], and press 
the  button.
[NETWORK STATUS]
Displays the status of the network for the projector 
body. 
1)  Press ▲▼ to select [NETWORK 
STATUS]. 
2)  Press the  button. 
 
z
The [NETWORK STATUS] screen is displayed.  
						

							[NETWORK] menu 
74 - ENGLISH
Settings
Network connections
The projector has a network function, and the following operations are available from the computer using the Web 
browser control.  
z
Setting and adjustment of the projector
 
z
Display of the projector status 
 
z
Transmission of an E-mail message when there is a problem with the projector 
Note  
z
A LAN cable is required to use the network function. 
Computer
Projector
LAN cable (straight) LAN cable (straight)
Hub
 
z
A Web browser is required to use this function. Confirm that the Web browser can be used beforehand. 
Compatible OS:   Windows XP/Windows Vista/Windows 7, Mac OS X v10.4/v10.5/v10.6
Compatible browser:  Internet Explorer 6.0/7.0/8.0, Safari 2.0/3.0/4.0 (Mac OS)
 
z
Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be 
used beforehand. 
 
z
Use a LAN cable that is straight-through and compatible with category 5 or higher.
  
 
z
Use a LAN cable with length of 100 m or shorter. 
 
■ Name and function of network function parts 
(1) (2) (3)
(1) LAN 10/100 lamp (yellow)
Lights on when connected to the 100BASE-TX. 
(2)  terminal (10BASE-T/100BASE-TX)  Used to connect the LAN cable here.  (3) LAN LINK/ACT lamp (green)
Lights on when connected. 
Flashes when transmitting/receiving data. 
Attention
 
z
Connect the LAN to the indoor equipment. 
						

							[NETWORK] menu 
ENGLISH - 75
Settings
Accessing from the Web browser 
1)  Start up the Web browser on the computer. 
2)  Enter the IP address set on the projector into the URL entry field of the Web browser.  3)  Enter the user name and the password. 
 
z
The factory default setting of the user name is user1 (user rights)/ad\
min1 (administrator rights) and the 
password is panasonic (lower case). 
4)  Click [OK]. 
 
z
The [Projector status] page is displayed. 
Note
 
z
 When you wish to control the projector via the Web browser, set [WEB CONTROL] to [ON] in [NETWORK 
CONTROL] (
 page 73).
 
z
Do not perform setting or control simultaneously by starting up multiple Web bro wsers. Do not set or control the 
projector from multiple computers.
 
z
Change the password first. (
 page 86)
 
z
The administrator rights allows to use all functions. The user rights only allows to use [Projector status]
(
 page 7 6), con firmation of the error information page ( page 77), [Net work status] ( page 78), [Basic control] 
(
 page 79), and [Change password] ( page 86). 
 
z
Access will be locked for few minutes when an incorrect password is entered three times consecutively.  
						

							[NETWORK] menu 
76 - ENGLISH
Settings
 
■ Item description
(1)
(2)
(3)
(4)
(5) (1) Page switch tab
Click the tab to switch between pages.
(2) [Status] The status of the projector is displayed by clicking 
this item. 
(3) [Projector control] The [Projector control] page is displayed by clicking 
this item.
(4) [Detailed set up] The [Detailed set up] page is displayed by clicking 
this item. 
(5) [Change password] The [Change password] page is displayed by 
clicking this item. 
 
■ [Projector status] page
Click [Status] 
 [Projector status]. 
Displays the status of the projector for the following items. 
(11)
(12)
(13)
(14)
(15)
(16)
(17) (6)
(7)
(8)
(9)
(10)
(1)
(2)
(3)
(5) (4)
(1) [PROJECTOR TYPE]
Displays the type of the projector. 
(2) [MAIN VERSION] Displays the firmware version of the projector. 
(3) [POWER] Display the power status.
(4) [SHUTTER] Displays the shutter status.
(5) [LAMP SELECT] Displays the [LAMP SELECT] setting (
 page 62).
(6) [SERIAL NUMBER] Displays the serial number of the projector.
(7) [NETWORK VERSION] Displays the network firmware version.
(8) [REMOTE2 STATUS] Displ ays the control status of the  
t

erminal.
(9) [OSD] Displays the on-screen display status.
(10) [LAMP POWER] Displays the [LAMP POWER] setting (
 page 63).
(11) [INPUT] Displays the status of the input selection. 
(12) [INPUT AIR TEMPERATURE] Displays the status of the air intake temperature of 
the projector. 
(13) [OPTICS MODULE TEMPERATURE] Displays the status of the internal temperature of 
the pro jector.
 
(14) [AROUND LAMP TEMPERATURE] Displays the status of the temperature around the 
lamp of the projector. 
(15) [LAMP1]/[LAMP2]/[RUNTIME] Displays the status and the usage time of the lamp. 
(16) [SELF TEST] Displays the self-diagnosis information. 
(17) [PROJECTOR RUNTIME] Displays the operation times of the projector.  
						

							[NETWORK] menu 
ENGLISH - 77
Settings
 
■ Error information page
When [Error (Detail)] is displayed on the [Projector status] screen, c\
lick it to display the error details.
 
z
The projector may go into the standby status to protect the projector de\
pending on the contents of the 
error. 
[OK]: Normal operation
[FAILED]: Occurrence of trouble
 
z
Description of problem occurrence [FAILED]: 
Parameter  Description
[MAIN CPU BUS] There is a problem with the microcomputer circuitry. Consult your 
dealer. 
[FAN] There is a problem with the fan or the fan drive circuit. Consult your 
dealer.  
[INTAKE AIR TEMPERATURE] The air intake temperature is too high. It may be used in an operating 
environment where the temperature is high, such as near a heating 
appliance.
[OPTICS MODULE TEMPERATURE] The temp
erature inside the projector is high. It may be used in an 
o

perating environment where the temperature is high, such as near a 
heating appliance.
[AROUND LAMP TEMPERATURE] The temperature around the lamp is high. The air exhaust port may 
be blocked. 
[LAMP1 REMAIN TIME] The usage time of the lamp has exceeded the specified time, and it is 
time to replace the lamp. 
[LAMP2 REMAIN TIME]
[LAMP1 STATUS] The lamp has failed to turn on. Wa

it a while until the luminous lamp 
cools off, and then turn on the power. 
[LAMP2 STATUS]
[SHUTTER] There is a problem with the shutter circuitry. Consult your dealer.  
[INTAKE AIR TEMP.SENSOR] There is a problem with the sensor used to detect intake air 
temperature. Consult your dealer.  
[OPTICS MODULE TEMP.SENSOR] There is a problem with the sensor used to detect temperat
ure inside 
t

he projector. Consult your dealer.  
[AROUND LAMP TEMP. SENSOR] There is a problem with the sensor used to detect exhaust air 
temperature. Consult your dealer.  
[BATTERY] The battery replacement is required. Consult your dealer. 
[AIRFLOW SENSOR]
There is a problem with the air volume sensor. Consult your dealer. 
[COLOR WHEEL] There is a problem with the color wheel or the color wheel drive 
circuit. Consult your dealer.
   
[COVER OPEN] The attachment of the lamp unit cover is incomplete. Check the lamp 
unit cover. (
 page 92)
[FILTER UNIT] The air filter unit is not attached. Check the air filter unit. (
 page 90)
[AIR FILTER] There are too much dust accumulated in the air filter unit. 
Set the  s
witch (
 page 3 5) to , and clean the 
air filter (
 page 89). 
						

							[NETWORK] menu 
78 - ENGLISH
Settings
 
■ [Network status] page
Click [Status] 
 [Network status].
The current network setting status is displayed. 
 
■ [Access error log] page
Click [Status] 
 [Access error log].
The error log on the WEB server is displayed such as access to the pages\
 that do not exist or access with 
unauthorized user names or passwords.
 
■ [Access log] page
Click [Status] 
 [Access log].
The log such as user name accessed to the WEB control page, accessed IP address, accessed time is 
displayed.
Note
 
z
[Access error log]/[Access log] will display the recent few thousand accesses/requests. If many accesses/
requests are made at a time, some of them may not be found in the informati\
on. 
 
z
Confirm [Access error log]/[Access log] periodically.  
						

							[NETWORK] menu 
ENGLISH - 79
Settings
 
■ [Basic control] page
Click [Projector control] 
 [Basic control]. 
(1)
(2)
(3)
(4)
(6)
(5) (1) [POWER] ([ON]/[STANDBY])
Switches between on/off of the power. 
(2) [SHUTTER] ([ON]/[OFF]) Switches between use or not use of the shutter 
function. 
(3) [OSD] ([ON]/[OFF]) Switches between on (display)/off (no display) of the 
on-screen display function. 
(4) [SYSTEM] ([SELECTOR]) Switches the system method. 
(5) On-screen display of the projector The same contents as the on-screen display of the 
projector  are displayed here. T

he confirmation and 
change of the setting contents of the menu can be 
performed. This is displayed even if the on-screen 
display function is set to off (no display). 
(6) [INPUT SELECT] ([RGB1]/[RGB2]/[DVI-D]/ [VIDEO]/[S-VIDEO])
Switches the input signal.
 
■ [Detail control] page
Click [Projector control] 
 [Detail control]. 
(1)
(2)
(8) (3)
(4)
(5)
(6)
(7)
(1) Control of the projector
The projector is controlled by pressing the buttons 
as the buttons on the remote control. The on-
screen display of the projector at the right of the 
control page is updated after the controlling. 
(2) [LENS] Adjusts the projection lens. 
(3) [TEST PATTERN] Displays the test pattern. 
(4) [GET OSD] Updates the on-screen display of the projector at 
the right of the control page. 
(5 ) [
SUB MEMORY]
Switch the sub memory 
(6) [SYSTEM DAYLIGHT VIEW] Switches the system daylight view settings.
(7) [FREEZE] Turn the projected image to the still image 
temporarily.
(8) [SIDE BY SIDE] (PT-DW730U only) Two different input signals can be displayed 
simultaneously.  
						

							[NETWORK] menu 
80 - ENGLISH
Settings
 
■ [Network config] page
Click [Detailed set up] 
 [Network config]. 
 
z
The [CAUTION!] screen is displayed by clicking [Network config]. 
 
z
The current settings are displayed by pressing the [Next] button. 
 
z
The following setting change screen is displayed by pressing the [Change] button. \
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) (1) [PROJECTOR NAME]
Enter the name of the projector. Also enter the host 
name if it is required when using a DHCP server, etc. 
(2) [DHCP ON]/[DHCP OFF] To enable the DHCP client function, set to [DHCP 
ON]. 
(3) [IP ADDRESS] Enter the IP address when not using a DHCP server. 
(4) [SUBNETMASK] Enter the subnet mask when not using a DHCP 
server. 
(5) [DEFAULT GATEWAY] Enter the gateway address wh en not using a DHCP 
s

erver. 
(6) [DNS1] Allowed characters for the entry of DNS 1 server 
address (primary): 
Numerics (0 - 9) and period (.)
(Example: 192.168.0.253) 
(7) [DNS2] Allowed characters for the entry of DNS 2 server 
address (secondary): 
Numerics (0 - 9) and period (.)
(Example: 192.168.0.254) 
(8) [Back]/[Next] Press [Next] to display the setting confirmation 
screen. Press [Submit] to update the set tings. 
 
■ [Adjust clock] page
Click [Detailed set up] 
 [Adjust clock]. 
(1)
(2)
(3)
(4)
(5) (1) [Time zone]
Selects the time zone. 
(Japan is GMT +09:00) 
(2) [Set time zone] Updates the time zone setting. 
(3) [Date] Enter the date to be changed. 
(4) [Time] Enter the time to be changed. 
(5) [Set date and time] Updates the date and time settings. 
Note
 
z
The replacement of the battery inside the projector is required when the time goes out of alignment right after 
correcting the time. Please consu lt your dealer.