Panasonic Projector Pt Dw5100u Operating Instructions

41
Setting the network
The settings required for the network must be
established in order to use the Web browser (page 42)
functions that the PC uses to control the projector.
HOST NAME : Make alteration if necessary
when to use the DHCP
server.
DHCP : Set the DHCP item to ON
when to acquire an IP
address automatically using
the DHCP server. 
Set to OFF if DHCP server is
not used.
IP ADDRESS : Enter the IP address if DHCP
server is not used.
SUBNET MASK : Enter the subnet mask if
DHCP server is not...

42
Using Web Browser Control 
Accessing from the Web browser
Start the Web browser on your PC, then
enter the IP address which was set in
the projector.
Enter “user1” in the user name field,
then enter the password in the
password field.
The default setting is “panasonic” (all lower case). If
you have changed the password, enter the new
password here. 
The host name set in the projector is displayed in
the “Realm” field.
Click [OK]. 
The Basic Control page is displayed.
Password change page
Click [Change...

43
Basic control page
This page is the first page displayed when the projector is accessed through a Web browser.
To move from another page, click [Projector control], then [Basic control]. 
Detail control page
Click [Projector control], then [Detail control] to display the Detail control page.
Control button
Click this item, and a
projector control page
appears.E-mail set up button
Click this item, and an E-mail setting
page appears.
SYSTEM: Signal System Switching
Change password buttonNetwork set up...

44
Using Web Browser Control 
Error information page
When  is displayed on the status information screen, click it to display the error details.
• Depending on the nature of the error, the projector may be placed in the standby mode for its own
protection.Note
Monitor information page
Click [Projector control], then [Status information] to display the Status information page.
This page displays the projector statuses established for the items shown below.
Displays self-diagnosis information.
Displays...

45
When [FAILED] has appeared for an item
Parameter
MAIN CPU BUS
FAN
OPTICS MODULE
TEMPERATURE
INPUT AIR TEMPERATURE
AROUND LAMP
TEMPERATURE
LAMP REMAIN TIME
LAMP STATUS
SHUTTER
AIR FILTER
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
AROUND LAMP 
TEMP. SENSOR
BATTERY
AIRFLOW SENSOR
COLOR WHEEL
COVER OPEN
Description
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
The temperature inside the projector is...

46
Using Web Browser Control 
• Only alphanumeric characters, “.”, “_”, “-”, or “@” are available to set an E-mail address.Note
Periodic warning interval setting (E-mail
is sent on the checked days of the
week/times)
Enter the E-mail address of your
desired recipient.
Select the conditions for sending E-mail.
ERROR:
an error is detected by self-
diagnosis.
LAMP RUNTIME:
remaining lamp service time has
reached the value set in the field.
INPUT AIR TEMPERATURE:
intake air temperature has reached the
value...

47
Authentication server set up page
The authentication server is set on this page when POP authentication or SMTP authentication is required for mail transmissions.
Click [Network set up], then [Authentication set up] to display the authentication server set up page.
For SMTP authentication, change the
authentication method to use, as desired.
Change the authentication method as desired.
Enter the POP server name.
Available input characters:
alphanumeric characters (A - Z, a - z, 
0 - 9), hyphen (-)...

48
Using Web Browser Control 
Contents of mail sent
• Mail with the contents shown below is sent when the E-mail
settings have been established.
Adjust clock page
Click [Network set up], then [Adjust clock] to display the Adjust clock page.
• Mail with the contents shown below is sent
when an error has occurred.
• If the time becomes incorrect immediately after setting the correct time, then the battery needs to
be changed. Contact the dealer where you bought the projector to have the battery changed....

49
Network config page
Click [Network set up], then [Network config] to display the Network config page.
Network status page
Click [Network set up], then [Network status] to display the Network status page.
Set this to ON to enable the DHCP client
function.
Enter the IP address if DHCP server is
not used.
Enter the gateway address if DHCP
server is not used.
Enter the name of the projector here. Enter the host name
here if it is required when the DHCP server is going to be
used, for instance.
Enter the...

50
Using the PJLink™protocol
The network functions of the projector are compatible with PJLink™Class 1. The operations mentioned below can
be performed from a personal computer using the PJLink™protocol.
• Projector settings
• Projector status inquiry
Supported commands
The commands for controlling the projector using the PJLink™protocol are as given in the table below.
PJLink™security authentication
The password used for PJLink™is the same as the password set for WebBrowser control. 
When using these...