Panasonic Projector Pt D5500 Specifications

							31
ENGLISH
INPUT RESOLUTION
Input resolution adjustment achieves the best
image when the screen flickers or halo is observed
around the contour.
: These select the items listed below.
: These select the value.
“TOTAL DOTS”, “DISPLAY DOTS”, “TOTAL
LINES” and “DISPLAY LINES”
Each item automatically displays a value in
response to the type of the input signal. If vertical
stripes appear on the screen or the image is partly
missing, increase or decrease the displayed value
while observing the screen to achieve the optimal
value.
CLAMP POSITION
(For RGB/YPBPRsignals only)
Use the clamp position adjustment to achieve the
optimal value when dark areas of the image are
crushed or displayed in green.
Adjust with the  buttons.
The value changes from 0 to 255.
The optimal value for the clamp position adjustment
• If dark areas are crushed:
The optimal value is the point where the dark
area is best improved.
• If the dark areas are displayed in green:
The optimal value is the point where the
green area becomes dark and clear.
EDGE BLENDING
This projector has the function to hide the seams
for multi-screens.
Press to select “EDGE
BLENDING”.
Press to switch “EDGE
BLENDING”.
OFF : When the multi-screens are not going to
be used.
ON : When using “EDGE BLENDING” function.
Press to select “BRIGHT
ADJUST”.
Press the ENTER button.
The “BRIGHT ADJUST” screen will be displayed.
Press to select “BRIGHT INSIDE”.
Press the ENTER button.
The “BRIGHT INSIDE” adjustment screen will be
displayed.
When “INTERLOCKED” is set to “OFF”,
individual adjustment of “R”, “G” and “B” will be
possible.
Press the ENTER button.
The “EDGE BLENDING” screen will be displayed.
Press  to specify the area to be
adjusted.
• To joint the top : set “UPPER” to “ON”.
• To joint the bottom : set “LOWER” to “ON”.
• To joint the left : set “LEFT” to “ON”.
• To joint the right : set “RIGHT” to “ON”.
Press the ENTER button to toggle “ON”
and “OFF”.
Press  to adjust the compensation
width and start position.

Press to select “MARKER”.
Press the ENTER button to select “ON”.
A marker for adjusting the picture position appears.
The optimal point is the position where the red line
of one frame overlaps the green line of the other
frame.  However, depending on the installation
environment or the lens to be used, dot-
misalignment may occur.
The correction widths of the jointed frames must be
the same value all the time. The optimal joint
cannot be achieved if the jointed frames have
different correction widths.
• The abovementioned vertical stripes
will not appear on the screen when all
white signals are input.
• 
The picture may be distorted during the
adjusting operation, but this is not a fault.
• The input resolution can be adjusted
only when RGB signal input is applied
with RGB1 and RGB2 IN.
• Automatic adjustment is not available
if signals having a dot clock frequency
of more than 150 MHz are supplied.
Note
• The clamp position can be adjusted
only when the RGB signal input is
applied with RGB1 and RGB2 IN.
Note
The optimal point is where these lines overlap.
Red line Red lineGreen line Green line
(Continued on the next page)
%&~	
@&O
 
 
 
 .
 
 
						

							32
How to use ADVANCED MENU
Changing the display language
RASTER POSITION
When the whole area where the input picture can
be displayed is not used, the picture can be moved
to any position inside the display area.
: These adjust the value in the horizontal
direction.
: These adjust the value in the vertical
direction.
XGA MODE
This mode takes effect only when XGA (RGB)
signals are input.
XGA : This is the standard setting.
WXGA : Select this mode when WXGA signals
are input.
SXGA MODE
This mode takes effect only when SXGA (RGB)
signals are input.
SXGA : This is the standard setting.
SXGA+: Select this when the screen is cut off.
DISPLAY LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
ÔŠ 
¤
SELECT
SET
Menus, setting items, adjustment screens, and
control button names will be displayed in the
language the user chooses.
The available languages are:
ENGLISH, DEUTSCH, FRANÇAIS, ESPAÑOL,
ITALIANO, , ,  , .
• The projector’s on-screen display is
set to the English language by default.Note
Press  to select an item, and press
to adjust the setting.
Once adjustment is complete, press the MENU
button to return to “BRIGHT ADJUST”.
Press  to select the part of
“UPPER”, “LOWER”, “RIGHT”, “LEFT”.
Use  to adjust the width for
correcting the “BRIGHT INSIDE” setting
(0 to 255).
Press to select “BRIGHT OUTSIDE”.
Press the ENTER button.
The “BRIGHT OUTSIDE” adjustment screen
will be displayed.
When “INTERLOCKED” is set to “OFF”, individual
adjustment of “R”, “G” and “B” will be possible.
Press  to select an item, and press
to adjust the setting.
Projection range Edge blending width (right) 
BRIGHT adjustment (right)
Marker
BRIGHT INSIDE BRIGHT OUTSIDE
• The “BRIGHT ADJUST” is a function for
making the brightening of the bright level
in those areas where the pictures
overlap less conspicuous when multi-
screens have been configured using
“EDGE BLENDING”. The optimal point is
where, after the “BRIGHT INSIDE” has
been adjusted, the compensation
amount is the same for the bright levels
in the areas where the pictures overlap
and where the pictures do not overlap. 
If, after the “BRIGHT INSIDE”
adjustment, only the vicinity of the
borders of the areas where the
pictures overlap and where the
pictures do not overlap becomes
bright, proceed to adjust the top,
bottom, left and right widths.
Alternatively, if only the vicinity of the
borders has darkened as a result of
the width adjustments, proceed with
the “BRIGHT OUTSIDE” adjustment.
• When a rear screen or screen with a
high gain is used, the joints may
appear to be discontinuous depending
on the viewing position.
• When any setting other than “OFF”
has been selected for “EDGE
BLENDING”, the “AI” is not adjustable.
Note
%&~	
@&O
 
 
 
 .
 
 
						

							33
ENGLISH
OPTION1 settings
OPTION1
COLOR MATCHING
COLOR CORRECTION
CONTRAST MODE
AUTO SIGNAL 
BACK COLOR 
STARTUP LOGO
SUB MEMORY LIST
DVI EDID
CHANGE MENU SELECTOFF
USER
 NORMAL
OFF
BLUE
OFF
EDID2:PC
DVI SIGNAL LEVEL0-255:PC
FUNC1
OSD POSITION1
OSD MEMORYON
COLOR MATCHING
When multiple sets are used simultaneously, this
projector allows the user to correct the difference of
colours among the sets.
Press to select “COLOR
MATCHING”.
Press to switch “COLOR
MATCHING”.
The setting will change as follows each time 
is pressed.
OFF : Colour matching adjustment is not
carried out.
3COLORS : It is possible to adjust the 3 colours
of “R (Red)”, “G (Green)” and “B
(Blue)” and “Wh (White)”*.
* When “3COLORS” is selected,
only the brightness can be
adjusted for “Wh”.
7COLORS : It is possible to adjust the 7 colours
of “R (Red)”, “G (Green)”, “B (Blue)”,
“Cy (Cyan)”, “Mg (Magenta)”, “Ye
(Yellow)” and “Wh (White)”.
MEASURE : Refer to “Adjusting the colour
matching using a colourimeter” on
the right for details on these modes.
If “3COLORS” or “7COLORS” was selected in step
2.
Press the ENTER button.
The “COLOR MATCHING: 3COLORS” or “COLOR
MATCHING: 7COLORS” screen will be displayed.
Press to select “R”, “G”, “B” and
“Wh”. 
(“R”, “G”, “B”, “Cy”, “Mg”, “Ye” and “Wh” when
selecting “7COLORS”.)
Press the ENTER button.
Press  to adjust the values.
These values can be adjusted from 0 to 2048.
(If the default value of the colour is 2048, the value
can be adjusted from 256 to 2048.)
Adjusting the colour matching
using a colourimeter
The “R (Red)”, “G (Green)”, “B (Blue)”, “Cy (Cyan)”,
“Mg (Magenta)”, “Ye (Yellow)” and “Wh (White)”
colours can be changed to the desired hues using a
colourimeter which is capable of measuring the
chromaticity coordinates and luminance.
Inputting the current luminance and chromaticity
coordinates
Press to select “COLOR
MATCHING”.
Press to select “MEASURE”.
Press the ENTER button.
The “COLOR MATCHING:MEASURE” screen will
be displayed.
Press to select “MEASURED DATA”.
Press the ENTER button.
The “MEASURED DATA” screen will be displayed.
Use the colourimeter to measure the
luminance (Y) and chromaticity
coordinates (x, y).
Press  to select the colours, and
press  to select their values.
• The effects of correcting the adjustment colour
When tuning the correction colour that
is the same as the adjustment colour
: The brightness of the adjustment
colour changes.
When tuning the correction colour RED
: RED is added to or reduced from
the adjustment colour.
When tuning the correction colour GREEN
: GREEN is added to or reduced
from the adjustment colour.
When tuning the correction colour BLUE
: BLUE is added to or reduced from
the adjustment colour.
• This adjustment should be carried out
by a person who is familiar with the
projector or by a service person
because a high level of skill is required
to make successful adjustment.
• 
Pressing the DEFAULT button will
restore the factory defaults for all items.
• When any setting other than “OFF”
has been selected for “COLOR
MATCHING”, “AI”, “COLOR
CORRECTION” and “COLOR TEMP”
settings are not adjustable.
• When “AUTO TESTPATTERN” is set
to “ON”, the test pattern for adjusting
the adjustment colour is automatically
displayed.
Note
(Continued on the next page)
%&~	
@&O
 
 
 
 .
 
 
						

							34
OPTION1 settings
COLOR CORRECTION
OFF : This is the standard setting.
USER : The six colours of red, green, blue, cyan,
magenta and yellow can be adjusted
and registered for each of four signal
systems: Video, S-Video, RGB and
YP
BPR.
Press the ENTER button to make the
detailed settings.
RETURN STORE
SUB MEMORY LIST
   
 
  - : RGB1-XGA60
1: RGB1-XGA60
2: VIDEO-NTSC
3:
4: 
5: 
6: 
7: 
8:
SELECT
CONTRAST MODE
There are two modes for adjusting to the operating
environment.
NORMAL : The brightness is set to maximum.
HIGH : The contrast is set to maximum.
AUTO SIGNAL
The position where the screen is displayed can be
adjusted automatically without pressing the AUTO
SETUP button on the remote control each time
signals are input when signals are input frequently
such as when the projector is used at a conference.
ON : Auto setup is performed automatically
when the video signals of the images
being projected have changed.
OFF : The input auto setup function is set to
OFF.
BACK COLOR
You can set the colours of the screen when no
signal is input to the projector.
BLUE : Set screen colour to blue.
BLACK : Set screen colour to black.
LOGO1 : The picture registered by the user will
be projected.
LOGO2 : The Panasonic logo is projected.
STARTUP LOGO
This sets the startup logo that is projected when the
power is turned on.
LOGO2 : This is the standard setting. The
Panasonic logo is projected.
NONE : “STARTUP LOGO” is disabled.
LOGO1 : The picture registered by the user will
be projected.
SUB MEMORY LIST
Multiple sets of image adjustment data (PICTURE,
POSITION, ADVANCED MENU adjustment values)
for the same kind of signal can be registered.
COLOR CORRECTION
RRGB
G
B
Cy
Mg
Ye
ADJUST MENU SELECT
0 0
0
0
0
0
The current signal system is displayed.
After all the data has been input, press
the MENU button.
The “COLOR MATCHING:MEASURE” screen will
be displayed.
Inputting the coordinates of a desired colour
Press to select “TARGET DATA”.
Press the ENTER button.
The “TARGET DATA” screen will be displayed.
Press  to select the desired
colours, and press  to input their
coordinates.
After all the data has been input, press
the MENU button.
• If the target data is outside the colour
range of the projector, the colours will
not be projected correctly.
• 
When “AUTO TESTPATTERN” is set to
“ON”, the test pattern for adjusting the
adjustment colour is automatically displayed.
• Set “PICTURE MODE” to “DYNAMIC”
when measuring the measured data
using a colourimeter or other
measuring device.
• 
Depending on the measuring device being
used and the environment in which
measurements are made, discrepancies
sometimes occur in the colour coordinates
of the target data and the values given by
the measuring device.
Note
• Separate software is required in order
to create the pictures to use for
“LOGO1”. Consult your dealer.
Note
%&~	
@&O
 
 
 
 .
 
 
						

							35
ENGLISH
DVI EDID
When the projector and external equipment are
connected by DVI connection but a proper image
cannot be obtained, switch this setting.
EDID1
Select this mainly when external equipment
(DVD player, etc.) that outputs movie video
signals is connected to the DVI terminal.
EDID2:PC
Select this mainly when external equipment
(personal computer, etc.) that outputs still
image video signals is connected to the DVI
terminal.
Mode
EDID1
EDID2:PCEDID data
480p, 576p, 1080/60i, 1080/50i,
720/60p, 720/50p, 1080/60p, 1080/50p
VGA60, SVGA60, XGA50, XGA60,
XGA70, XGA75, XGA85, WXGA768/50*,
WXGA768/60*, SXGA60
DVI SIGNAL LEVEL
When the projector and external equipment are
connected by DVI connection but a proper image
cannot be obtained, switch this setting.
0-255:PC
Select this mainly when connecting external
equipment (personal computer, etc.) using the
DVI terminal output.
16-235
Select this mainly when connecting external
equipment (DVD player, etc.) using the HDMI
terminal output with a conversion cable, etc.
FUNC1
The user can set the function for the remote
control’s FUNC1 button.
SYSTEM SELECTOR: 
The button functions in the same way as
“SYSTEM SELECTOR” of “PICTURE”.
SYSTEM DAYLIGHT VIEW:
This button has the same functions as
“SYSTEM  DAYLIGHT VIEW” of “PICTURE”.
SUB MEMORY LIST:
This button has the same functions as “SUB
MEMORY LIST” of “OPTION1”.
OSD POSITION
The user can specify the position of the on-screen
menu indications.
OSD MEMORY
This lets you save the cursor position in on-screen
menus.
ON : The cursor position is saved.
OFF : The cursor position is not saved.
How to erase sub memory
Select sub memory number (1 to 8) corresponding
to sub memory to be erased using  buttons.
Press the DEFAULT button.
Read the confirmation message and select.
How to select sub memory
Select sub memory number (1 to 8) using the
buttons. Select “–” if you do not wish to
use the sub memory.
Press the ENTER button.
• You cannot select sub memory of a
different signal system.Note
* PT-DW5100E, PT-DW5100EL only
• The optimum setting differs according
to the connected external equipment.
Be sure to check the operating
instructions for the external equipment,
etc.
• Depending on the setting, some
equipment may not provide images or
otherwise operate properly.
Note• 
The optimum setting differs according to
the connected external equipment. Be
sure to check the operating instructions
for the external equipment, etc.
• Depending on the setting, some
equipment may not provide images or
otherwise operate properly.
Note
1 (Top left of the screen)
9 (Bottom right of the screen)
8 (Right centre of the screen)5 (Centre of the screen)
7 (Top right of the screen)
2 (Left centre of the screen)
3 (Bottom left of the screen)
4 (Top centre of the screen)
6 (Bottom centre of the screen)
• Even when this is set to “ON”, the
cursor position is not saved if the main
power of the projector is turned off.Note Registering in sub memory
Select the sub memory number to be registered
using the  buttons.
Press the ENTER button.
• Sub memories range from 1 to 8.Note
%&~	
@&O
 
 
 
 .
 
 
						

							36
OPTION2 settings
OPTION2
PROJECTOR ID          
INSTALLATION
ALTITUDE
DIRECTION
LAMP SELECT
LAMP RELAY
LAMP POWER 
RS-232C
CHANGE MENU SELECTALL
FRONT-FLOOR
LOW
 HORIZONTAL
DUAL
OFF
HIGH
SYSTEM INFORMATION
AUTO POWER OFF
DATE AND TIME DISABLE
PASSWORD
PROJECTOR ID
The projector has an ID number setting function
that helps the user to control two or more projectors
either simultaneously or separately with a single
remote control. The ID number is set to “ALL” by
default. Hence the ID number need not be set
when only one projector is used.
1 – 64 : The ID number is set in this range.
• The ID number can be set to “ALL”, or
selected from “1” to “64”.
• If the projectors are given ID numbers,
their remote controls must be assigned
the same ID numbers, respectively.
• If the ID number of a projector is set to
“ALL”, it can be controlled by the
remote control or the PC with any ID
number. 
If multiple projectors are used and
some of them have their IDs set to
“ALL”, they cannot be controlled
separately from the projectors with
other ID numbers.
For details on remote control ID
setting, see page 15.Note
INSTALLATION
Switch this setting according to the projector
installation method.
FRONT-FLOOR
FRONT-CEILING
REAR-FLOOR
REAR-CEILING
ALTITUDE
The fan can be controlled in accordance with the
operating conditions.
LOW : This is the standard setting.
HIGH : This is selected when using the projector
at an altitude of over 1 400 m.
DIRECTION
The fan can be controlled in accordance with the
direction in which the images are to be projected.
HORIZONTAL : This is the standard setting.
VERTICAL : This is selected when projecting
images at a significant angle
toward the vertical (more than 30
degrees from the horizontal).
H: HORIZONTAL
V: VERTICAL
30° 30°
30° 30°
V
V HH
• Select the correct “DIRECTION” setting
in accordance with the direction in which
the images are to be projected.
Using the projector at the wrong
“DIRECTION” setting will shorten the
service life of the lamps.Attention
%&~	
@&O
 
 
 
 .
 
 
						

							37
ENGLISH
LAMP SELECT
“LAMP SELECT” is used to choose from “SINGLE”
and “DUAL” modes depending on user’s needs or
viewing conditions. 
In “SINGLE” mode, the projector may automatically
select either lamp from the 2 lamps, or the
particular lamp can be specified.
DUAL : Two lamps are used simultaneously.
SINGLE : 
One of either lamps is used (lamp with shorter
operating hours is automatically selected).
LAMP1 : Lamp Unit 1 is always used.
LAMP2 : Lamp Unit 2 is always used.
When one of the above settings is selected, it will
take effect after the ENTER button is pressed.
• If, in the “SINGLE”, “LAMP1” or
“LAMP2” mode, one lamp remains off
or the currently active lamp exceeds 
2 000 hours of cumulative operating
time (when “HIGH” is selected as the
“LAMP POWER” setting), the other
lamp will light. If, in the “DUAL” mode,
one lamp remains off or the currently
active lamp exceeds 2 000 hours of
cumulative operating time (when
“HIGH” is selected as the “LAMP
POWER” setting), the other lamp
alone will light.
However, if both lamps remain off or
the 2 000 hours of cumulative
operating time (when “HIGH” is
selected as the “LAMP POWER”
setting) are exceeded, the projector
will enter the standby mode.
• The colours of the items indicate the
status.
Green Current setting
Yellow Current setting (when a
lamp fails or fails to light)
Red Lamp that has failed to
light
White Any other status
• If the projector is repeatedly used for
short periods of time, the lamps will
need to be replaced more frequently.Note
LAMP RELAY
If using the projector for a continuous period of 24
hours or more, this setting can be used to
automatically switch the lamps that are turned on in
order to reduce the lamp deterioration that can
occur as a result of continuous use.
OFF : This is the standard setting. “LAMP
RELAY” is disabled.
00:00 - 23:00
: This can be set in one hour intervals from
00:00 to 23:00.
• Only when “DUAL” or “SINGLE” is
selected in “LAMP SELECT”, “LAMP
RELAY” is active. If “LAMP1” or
“LAMP2” is selected, “LAMP RELAY”
function is not available.
• When “DUAL” is selected in “LAMP
SELECT”, only one lamp will light for a
4-hour period after the set time.
• When “SINGLE” is selected in “LAMP
SELECT”, the lamp that was off at the
set time will light, and then the lamp
that was lighted until the set time will
turn off.
• The setting time will be the local time.
(page 38)Note
LAMP POWER
The luminance of the projection lamp can be
changed depending on user’s needs or the viewing
conditions.
HIGH : Set when high brightness is necessary.
LOW : Set when high brightness is not
necessary.
• When set to “LOW”, it is possible to
reduce power consumption, reduce
operating noise and extend lamp
service life.Note
RS-232C
This sets the communication parameters at the
serial terminals.
For details on the serial terminals, refer to “Using
the serial terminals” (page 51).
(IN) BAUDRATE : 9600, 19200 or 38400 is
selected.
(IN) PARITY : NONE, EVEN or ODD is
selected.
(OUT) BAUDRATE: 9600, 19200 or 38400 is
selected.
(OUT) PARITY : NONE, EVEN or ODD is
selected.
VPS SYSTEM : MASTER or SLAVE is
selected.
GROUP : A to Z is selected. MASTER
or SLAVE is also selected.
%&~	
@&O
 
 
 
 .
 
 
						

							38
OPTION2 settingsDisplaying the internal test pattern
SYSTEM INFORMATION
The projector’s system information can be viewed.
SYSTEM INFORMATION
MAIN VERSION
NETWORK VERSION
PROJECTOR RUNTIME
LAMP1 LOW
             HIGH
             TOTAL
LAMP2 LOW
             HIGH
LAMP1 ON              TOTAL
RETURN LAMP2 ON1.00.00
1.00      300h
100h
200h
300h
100h
200h
300h
20
20
AUTO POWER OFF
The projector can be automatically set to the
standby mode if no signals are input for the set
duration.
DISABLE: 
This is the standard setting. This function is set
to OFF.
45MIN. – 90MIN.: 
The duration can be set in 15-minute
increments from 45 to 90 minutes.
DATE AND TIME
This lets you set the time zone and the current date
and time for the projector’s internal clock.
TIME ZONE
: Set the time zone of your country.
ADJUST CLOCK
: Set the current date and time.
LOCAL DATE/LOCAL TIME
: Date and time set in above are displayed.
PASSWORD
This function is used by a service person.
Input the password with the numeric buttons (0 to
9) of the remote control and press the ENTER
button to confirm the entry.
The projector has eight types of internal test patterns
to check the condition of the set.
To display test patterns, follow the steps below.
Press the TEST PATTERN button on the
remote control.
Or select “TEST PATTERN” in the MAIN
MENU and search through the various
types of test  patterns by using 
buttons.
• Results of adjustment on the image,
picture quality, position, size and other
factors will not be reflected in test
patterns. Be sure to display the input
signal before performing various kinds
of setting.Note
Cycle of displayed internal
test patterns
MENU screen
 + 
Entry screen
All white
All black
Flag
16:9 frame*
Focus
Colour bars
Window (inversion)
Window
Black on 
white ground
White on 
black ground
* The PT-DW5100E and PT-DW5100EL support the
4:3 frame format.
%&~	
@&O
 
 
 
 .
 
 
						

							39
ENGLISH
Setting the networkConnecting the PC
The settings required for the network must be
established in order to use the Web browser (page 40)
functions that the PC uses to control the projector.
HOST NAME : 
Make alteration if necessary
when to use the DHCP server.
The number of valid characters
is 1 to 12 characters (spaces
not allowed).
DHCP : Set the DHCP item to ON when to
acquire an IP address automatically
using the DHCP server.
Set to OFF if DHCP server is
not used.
IP ADDRESS : Enter the IP address if DHCP
server is not used.
SUBNET MASK : Enter the subnet mask if
DHCP server is not used.
GATEWAY : Enter the gateway address if
DHCP server is not used.
NETWORK STATUS : Displays the network status
of the unit such as DHCP or
IP ADDRESS.
STORE : The settings are stored in the
memory.
NETWORK
HOST NAME
DHCP
IP ADDRESS
SUBNET MASK
GATEWAY
NETWORK STATUS
STORE
MENU SELECT
OFF192.168.    0.    8
255.255.255.    0
192.168.    0.    1
ADJUST
PROJECTOR
• Before using the DHCP server, make
sure the DHCP server is already
functioning.
• For details of IP address, subnet
mask, and gateway, ask the network
administrator.Attention
System requirements
The following system specifications are required in
order to use the networking functions.
• PC
OS : Windows XP/2000/Me (Millennium
Edition)/98SE (Second Edition)
CPU : Pentium  processor or faster
RAM : 64 MB or more (128 MB or more for
Windows XP/2000)
Web browser: Internet Explorer 6.0 or newer,
Netscape Communicator 7.0 or
newer
• LAN cable
Type : Category 5 compatible straight cable
Length : 100 m or less
• If you want to use the E-mail function,
make sure the system can handle E-
mail.
Operation is not guaranteed for all
computers that meet the above
conditions.
Connection example
• Touching the LAN terminal with your
hand (or body) when you are carrying
a static charge may damage the
equipment due to a discharge of static
electricity. Therefore, be careful not to
touch the LAN terminal or metal parts
of the LAN cable.
• Please connect the LAN cable to
indoor devices.Attention
RGB 2 IN
 VDSYNC/HDB/PBG/YRR/P
SERIALREMOTE 1
REMOTE 2 ININOUTLANDVI-D INRGB 1 INVIDEO INS-VIDEO  IN
IN OUT
Personal
computer
Hub LAN cable
(straight)LAN cable
(straight) Projector
10BASE-T or 100BASE-TX
Attention
Returning the network
function setting back to
the factory setting
The user can return all settings of network function
such as IP address, password and E-mail setting to
the factory setting.
Press to select “STORE”.
Hold down the DEFAULT button for 3
seconds.
A confirmation screen will be displayed.
To cancel, press the MENU button. The
“NETWORK” screen will be displayed.
Press the ENTER button.
%&~	
@&O
 
 
 
 .
 
 
						

							40
Using Web Browser Control 
Accessing from the Web browser
Start the Web browser on your PC, then
enter the IP address which was set in
the projector.
Enter “user1” in the user name field,
then enter the password in the
password field.
The default setting is “panasonic” (all lower case). If
you have changed the password, enter the new
password here. 
The host name set in the projector is displayed in
the “Realm” field.
Click [OK]. 
The Basic Control page is displayed.
Password change page
Click [Change password].
• Avoid activating two or more Web browser
simultaneously to work out setting or
control actions.
• Change the password first of all.Note This projector has networking functions which allow it to be controlled through a Web browser on a PC. 
The controlled items are:
• Projector’s settings and adjustment
• Projector’s status display
• Transmission of a E-mail message when the projector has a problem
New password input field
New password input field
(re-enter for confirmation)
Button for executing password change
Button for erasing all entered characters
Old password input field
%&~	
@&O
 
 
 
 .