Panasonic Projector Pt D5500 Specifications

51
ENGLISH
Using the serial terminals
Pin assignments and signal names
Communication conditions (Factory setting)
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
The main unit is equipped with SERIAL terminals located in its terminal section on the side, and this terminal is
compliant with RS-232C. Also a serial output terminal is provided to enable plural projector control....

52
Using the REMOTE2 IN terminal provided on the side of
the main unit, it is possible to operate the projector from a
control panel etc. furnished in a distant location where
infrared remote control signal cannot be received.
Pin assignments and control
Be sure to short-circuit Pins  and
when controlling.
Using the REMOTE 2 terminal
D-Sub 9-pin (female) 
external appearance
• The following buttons on the remote
control and the operation area of the
projector can no longer be operated when
pins and are...

53
ENGLISH
Indication of lamp monitor
This projector is equipped with 3 indicators to show when a lamp needs replacement or there is an abnormal
internal temperature. These lamps flash or light up to indicate a problem.
Turn the power off and follow the steps below.
Temperature monitor (TEMP) Lamp 1 monitor (LAMP 1) Lamp 2 monitor (LAMP 2) (Power indicator)
• To solve any problems that the TEMP and LAMP monitor show, first turn the power off by
following the steps on pages 22, 23.
• 
If the power...

54
Cleaning and replacement of air filter
If too much dust accumulates on the air filter, [CLEAN THE AIR FILTER]* appears at the lower left of the screen,
and the temperature monitor (TEMP) will blink once. If even more dust is allowed to accumulate, the temperature
inside the main unit will rise, the temperature monitor (TEMP) will blink twice, and the power is turned off.
Clean the air filter section once every 100 hours or so as a guideline depending on the location of projector
operation.
* It...

55
ENGLISH
Replacing the lamp unit
Precautions on lamp unit replacement
Remove the power plug and confirm that the surroundings of the lamp unit have cooled off.
Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled,
explosion might result.
A used lamp unit may burst if it is handled violently.
For disposition of used lamps, request an industrial waste disposal contractor.
If you continue to use a lamp after the replacement time, the lamp may...

56
Replacing the lamp unit
Lamp unit replacement steps
Turn the power off by following the steps on page 23, remove the power plug and
confirm that the surroundings of the lamp unit have cooled off.
Check that the fan has stopped running.
Have a Phillips screwdriver ready ahead of time.
Remove the screw securing the lamp unit
cover, and then slide the lamp unit cover
a little toward the left, and remove it.
Remove the two screws securing the
fan unit.
Lamp unit cover
Open the fan unit as shown in the...

57
ENGLISH
Ceiling Mount Bracket Safeguards
The projector and the ceiling mount bracket are designed sufficiently safety though, make sure the safety cable
provided with the projector is installed and attached to the bottom of the projector when mounting in the ceiling for
safety and security.
Installation work of the ceiling mount bracket should only be carried by a qualified technician according to the
following procedure.
• Even if it is guarantee period, the manufacturer is not responsible for any...

58
Before asking for service --- check the following points.
SymptomsChecks
• Is the power cord plug correctly plugged in?
• Is the MAIN POWER turned on?
• Is electricity running to the power outlet?
• Is the temperature monitor (TEMP) indicator on the front of the unit flashing or
turned on? (See page 53)
• Is the lamp monitor (LAMP) indicator on the front of the unit flashing or turned on?
(See page 53)
• Is the lamp unit door installed correctly?
• A wrong ID is set. (See pages 15 and 36)
Power does...

59
ENGLISH
Specifications
PT-D5700EPT-D5700ELPT-DW5100EPT-DW5100EL
Power supplyAC 220 - 240 V, 50 Hz/60 Hz
Power consumption750 W (about 15 W in standby without fan running)
DLPTMpanel
Panel size
Display system
Number of pixels0.7 inch (aspect ratio 4:3)0.65 inch (aspect ratio 15:9)
DLPTMchip x 1, DLPTMtype
786 432 pixels (1 024 x 768 dots)983 040 pixels (1 280 x 768 dots)
Lens
Powered zoom
Powered focus control
1 to 1.32
F=1.7 to 2.0  
f=25.6 mm to
33.8 mm1 to 1.32
F=1.7 to 2.0  
f=25.6 mm to
33.8 mm...

60
Specifications
Interface ports
RGB2 input terminal
Video input terminal
S-Video input terminal
Serial input/output terminal
Remote1 input/output terminal
Remote2 input terminal
DVI-D input terminal
LAN terminal
1 set of high-density, D-Sub 15-pin (female)
[For YP
BPRinput]
Y: 1.0 V [p-p] synchronization signal included, P
BPR: 0.7 V[p-p] 75 Ω
[For RGB input] 0.7 V[p-p] 75 ΩFor G-SYNC: 1.0 V[p-p] 75 Ω
HD/SYNC: TTL, high-impedance, positive/negative polarity
automatically adjusted
VD:
TTL,...