Panasonic Projector Pt D5500 Specifications

41
ENGLISH
Basic control page
This page is the first page displayed when the projector is accessed through a Web browser.
To move from another page, click [Projector control], then [Basic control]. 
Power On/Off control 
Shutter control
Network set up button
Click this item, and a network set up page for IP address and
other items appear.
Change password button
Signal System Switching
Control button
Click this item, and a projector control
page appears.
E-mail set up button
Click this item, and an E-mail...

42
Using Web Browser Control 
Detail control page
Click [Projector control], then [Detail control] to display the Detail control page.
Pressing these buttons controls the projector and updates the on-screen
description on the right of the control page when control is finished.
This button updates the on-screen
description on the right of the control
page with the latest information.
On-screen status is displayed, even if
the on-screen of projector is set to off.
Monitor information page
Click [Projector...

43
ENGLISH
When [FAILED] has appeared for an item
Parameter
MAIN CPU BUS
FAN
OPTICS MODULE
TEMPERATURE
INPUT AIR TEMPERATURE
AROUND LAMP
TEMPERATURE
LAMP REMAIN TIME
LAMP STATUS
SHUTTER
AIR FILTER
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
AROUND LAMP 
TEMP. SENSOR
BATTERY
AIRFLOW SENSOR
COLOR WHEEL
˜
COVER OPEN
Description
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
The temperature inside the...

44
Using Web Browser Control 
Periodic warning interval setting (E-mail
is sent on the checked days of the
week/times)
Enter the E-mail address of your
desired recipient.
Select the conditions for sending E-mail.
ERROR:
an error is detected by self-
diagnosis.
LAMP RUNTIME:
remaining lamp service time has
reached the value set in the field.
INPUT AIR TEMPERATURE:
intake air temperature has reached the
value set in the field.
E-mail set up page
With this projector, if a problem occurs or if the lamp usage...

45
ENGLISH
• Only alphanumeric characters, “.”, “_”, “-”, or “@” are available to set an E-mail address.Note
Select the conditions for sending the second E-mail.
ERROR:an error is detected by self-diagnosis.
LAMP RUNTIME:remaining lamp service time has reached the value set in the field.
INPUT AIR TEMPERATURE: intake air temperature has reached the value set in the field.
Enter the E-mail address to which the
E-mail is to be sent when two E-mail
addresses are going to be used. Do not
enter it when the...

46
Using Web Browser Control 
Ping test page
This page makes it possible to check whether the network is connected to the E-mail server, authentication server, DNS server, etc.
Click [Network set up], then [Ping test] to display the Ping test page.
Display which appears
when the connection was
successful.
Display which appears
when the connection failed.
DNS server set up page
Click [Network set up], then [DNS server set up] to display the DNS server set up page.
Primary DNS server address
Available...

47
ENGLISH
Contents of mail sent
• Mail with the contents shown below is sent when the E-mail
settings have been established.
Adjust clock page
Click [Network set up], then [Adjust clock] to display the Adjust clock page.
• Mail with the contents shown below is sent
when an error has occurred.
• If the time becomes incorrect immediately after setting the correct time, then the battery needs to
be changed. Contact the dealer where you bought the projector to have the battery changed.
Note
=== Panasonic...

48
Using Web Browser Control 
Network config page
Click [Network set up], then [Network config] to display the Network config page.
Network status page
Click [Network set up], then [Network status] to display the Network status page.
Set this to ON to enable the DHCP client
function.
Enter the IP address if DHCP server is
not used.
Enter the gateway address if DHCP
server is not used.
Enter the name of the projector here. Enter the host name
here if it is required when the DHCP server is going to be...

49
ENGLISH
Using the PJLink™protocol
The network functions of the projector are compatible with PJLink™Class 1. The operations mentioned below can
be performed from a personal computer using the PJLink™protocol.
• Projector settings
• Projector status inquiry
Supported commands
The commands for controlling the projector using the PJLink™protocol are as given in the table below.
PJLink™security authentication
The password used for PJLink™is the same as the password set for WebBrowser control. 
When using...

50
Setting the security
The projector’s security function enables the password
input screen to be displayed or a company’s URL
address to be set and displayed underneath the
projected images.
PASSWORD
SET INPUT
(When using the projector for the first time)
Press the , , , , , ,  and 
buttons in this order, and press the ENTER button.
(When the password has been changed)
Input the new password, and press the ENTER button.
PASSWORD 
It is possible to display the password input screen
each time the power is...