Panasonic Projector Pt D4000e Operating Instructions

21
ENGLISH
Projection
Powering up the projector
When using an optional lens, install a projection
lens before powering up the projector. (Refer to
page 23.)
Remove the lens cover beforehand.
Connect the supplied power cord. 
(220 - 240 V AC, 50 Hz/60 Hz)
Press the “ I ” marked side of the MAIN
POWER switch to turn on the power.
The power indicator lights up red, and the projector is
placed in the standby mode.
Press the “ I ” button. [on the main unit
or the remote control]
The power indicator...

22
Projection
Powering off the projector
Press the POWER STANDBY “”
button.
Select “OK” with  or  button and
press the ENTER button.
(Or press the POWER STANDBY “”
button again.)
The projection of the image stops, and the power
indicator of the main unit lights up orange. (The
cooling fan keeps running.)
Wait until the power indicator of the
main unit turns to red (i.e., until the
cooling fan stops). 
Press the “” marked side of the MAIN
POWER switch to remove all power
from the projector. 
• The...

23
ENGLISH
How to adjust the lensHow to install and remove
the projection lens
How to install the
projection lens
Align the guide of the projection lens
with the guide groove in the main unit.
Turn the lens clockwise until it clicks
into place.
How to remove the
projection lens
Turn the lens counterclockwise as
far as it will go.
While holding down the lens release
button, turn the lens further
counterclockwise.
Remove the lens.
Note• Before replacing the lens, turn off the
projector’s power.
• Do not...

24
How to adjust the lensAutomatic adjustment
(AUTO SETUP)
Automatic adjustment function adjust the resolution,
clock phase and image position automatically when
dots-structured analogue RGB signals such as
computer signal are supplied. (Automatic adjustment is
not available if moving picture input signals or signals
having a dot clock frequency of more than 150 MHz
are supplied.) When DVI signals are input, the image
position is adjusted automatically.
It is recommended to supply images with a bright...

25
ENGLISH
On-screen menus
Structure of menu screens
Menus are extensively used for configuring, adjusting or reconfiguring the projector.
The menus structure is as follows:
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
OPTION1
OPTION2
TEST PATTERN
NETWORK
SECURITY
SUB MENU MENU SELECT
NETWORK
HOST NAME
DHCP
IP ADDRESS
SUBNET MASK
GATEWAY
NETWORK STATUS
STORE
MENU SELECT
OFF192.168.    0.    8
255.255.255.    0
192.168.    0.    1
ADJUST
PROJECTOR
DISPLAY LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS...

26
On-screen menus
Returning to the previous
page
• Pressing the MENU button returns the screen to
the previous menu page.
• When the MAIN MENU is on the screen, pressing
the MENU button clears all menus from the
screen.
Menu items shown in
black characters
• Some menu items may not be valid for certain
signal formats applied to the projector. 
The menu items that cannot be adjusted or used
are shown in black characters, and they cannot be
selected.
Menu items setting
• The bottom prompt line differs on...

27
ENGLISH
Adjusting the picture
PICTURE MODE
The picture mode can be selected from the
following depending on viewing conditions and the
video signal source in use:
DYNAMIC : Picture brightness/contrast ratio is
increased to suit brighter viewing
environments.
GRAPHIC : The picture becomes suitable for
input from to the personal
computer.
STANDARD : The picture becomes suitable for
moving images in general.
CINEMA : The picture becomes suitable for
movie sources.
NATURAL : The picture becomes suitable...

28
Adjusting the pictureAdjusting the position
POSITION
SHIFT
ASPECT      
ZOOM
CLOCK PHASE 
KEYSTONE
MENU SELECT
4:3
+16
SUB MENU
SHIFT
The position where the images are displayed can
be moved here.
: The position is moved horizontally.
: The position is moved vertically.
ASPECT
AUTO : (For S-Video/Video signals only)At this setting, when S1 video signals*1are
identified as being input to the S-Video
connector or video ID signals are identified
as being input to the video connector, the
images are...

29
ENGLISH
• If the picture size is compressed or
enlarged by using the 16:9 aspect ratio
when the projector is used for
profitable purpose or in the presence
of an audience (for example, in a
coffee shop or at a hotel etc.), it may
infringe the rights of the copyright
owner of the original picture.
• 
If a picture with the standard (4:3)
aspect ratio is projected at a wide
aspect ratio, parts of the picture may run
over the screen bounds or the overall
picture may be distorted. To view the
picture at...

30
How to use ADVANCED MENU
Changing the display language
RASTER POSITION
When the whole area where the input picture can
be displayed is not used, the picture can be moved
to any position inside the display area.
: These adjust the value in the horizontal
direction.
: These adjust the value in the vertical
direction.
XGA MODE
This mode takes effect only when XGA (RGB)
signals are input.
XGA : This is the standard setting.
WXGA : Select this mode when WXGA signals
are input.
SXGA MODE
This mode takes...