Panasonic Projector Pt D12000u Operating Instructions

							ENGLISH – 51
Basic Operation
On-screen menus
 
MAIN MENU
The main menu consists of the following 11 menu 
items. When a main menu item is selected, the screen 
changes to a sub-menu selection screen.
Icon MAIN MENU item
PICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
P IN P
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
  SUB MENU
The sub-menu screen appears, and you can set and 
adjust the various items in the sub-menu.
PICTURE (pp. 54-59)  „
ENTER
PICTURE
PICTURE MODE
 CONTRAST
 BRIGHTNESS
 COLOR
 TINT
 COLOR TEMPERATURE
 GAMMA
 SYSTEM DAYLIGHT VIEW
 SHARPNESS
 NOISE REDUCTION
 DYNAMIC IRIS
SYSTEM SELECTOR
 MENU SELECT
 CHANGE REGISTERSTANDARD
0
0
0
0
DEFAULT
DEFAULT
OFF
0
OFF
OFF
AUTO1
Note
The factory default values may vary depending on  • 
the PICTURE menu.
▲▼◄►
ENTER
DEFAULT MENU
Menus are extensively used for configuring, 
adjusting or reconfiguring the projector.
MENUPress to display the MAIN 
MENU screen.
Select the item to be set.
Press to display the menu 
of the desired item.
ENTER
MAIN MENU
 PICTURE
 POSITION
 ADVANCED MENU
 DISPLAY LANGUAGE
 DISPLAY OPTION
 PROJECTOR SETUP
  P IN P
 TEST PATTERN
 SIGNAL LIST
 SECURITY
 NETWORK
 MENU SELECT
 SUB MENU
Some menu items may not be valid for certain  • 
signal formats applied to the projector. 
The menu items that cannot be adjusted or used 
are shown in gray characters, and they cannot 
be selected. 
						

							52 – ENGLISH
On-screen menus (continued)
POSITION (pp. 60-63)  „
ENTER
POSITION
SHIFT
ASPECT
ZOOM
CLOCK PHASE
GEOMETORY
 MENU SELECT
 SUB MENUDEFAULT
0
OFF
ADVANCED MENU (pp. 64-68)  „
ADVANCED MENU
DIGITAL CINEMA REALITY
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING
FRAME DELAY
RASTER POSITION
 MENU SELECT
 CHANGEAUTO
OFF
DEFAULT
DISPLAY LANGUAGE (p. 69)  „
ENTER
DISPLAY LANGUAGE
C ENGLISH
 DEUTSCH
 FRANÇAIS
 ESPAÑOL
 ITALIANO
 
ÔŠ  ¤ UXVVOMN à´	¯
 SELECT
 SET
DISPLAY OPTION (pp. 70-76)  „
DISPLAY OPTION
COLOR MATCHING
LARGE SCREEN CORRECTION
SCREEN SETTING
RGB IN
DVI-D IN
AUX DVI IN
AUX SDI IN
ON-SCREEN DISPLAY
BACK COLOR
STARTUP LOGO
 MENU SELECT
 CHANGEOFF
OFF
BLACK
LOGO3
PROJECTOR SETUP (pp. 77-84)  „
PROJECTOR SETUP
PROJECTOR ID
INSTALLATION
ALTITUDE MODE
DIRECTION
LAMP SELECT
LAMP RELAY
RS-232C
REMOTE2 MODE
STATUS
AIR FILTER CLEANING
AUTO POWER OFF
FUNC1
 MENU SELECT
 CHANGEALL
FRONT-FLOOR
ON
HORIZONTAL
QUAD
OFF
DEFAULT
DISABLE1/2
PROJECTOR SETUP
DATE AND TIME
SAVE ALL USER DATA
LOAD ALL USER DATA
INITIALIZE
SERVICE PASSWORD2/2
P IN P (pp. 85-86)  „
TEST PATTERN (p. 87)  „
SIGNAL LIST (pp. 45-47)  „
SECURITY (pp. 88-90)  „
SECURITY
SECURITY PASSWORD
SECURITY PASSWORD CHANGE
DISPLAY SETTING
TEXT CHANGE
CONTROL DEVICE SETUP
 MENU SELECT
 CHANGEOFF
OFF
NETWORK (pp. 91-104)  „
NETWORK
NETWORK STANDBY
NETWORK SETUP
NETWORK CONTROL
NETWORK STATUS
 MENU SELECT
 CHANGEOFF 
						

							ENGLISH – 53
Basic Operation
 
Using the menu screens
Press MENU. 1. 
The “MAIN MENU” appears on the screen. • 
ENTER
MAIN MENU
 PICTURE
 POSITION
 ADVANCED MENU
 DISPLAY LANGUAGE
 DISPLAY OPTION
 PROJECTOR SETUP
  P IN P
 TEST PATTERN
 SIGNAL LIST
 SECURITY
 NETWORK
 MENU SELECT
 SUB MENU
Press ▲▼ to select the desired  2. 
item.
The selected item is displayed with the colors  • 
set by OSD DESIGN. (p. 75)
ENTER
MAIN MENU
 PICTURE
 POSITION
 ADVANCED MENU
 DISPLAY LANGUAGE
 DISPLAY OPTION
 PROJECTOR SETUP
  P IN P
 TEST PATTERN
 SIGNAL LIST
 SECURITY
 NETWORK
 MENU SELECT
 SUB MENU
Press ENTER to establish your  3. 
selection.
The submenu for the selected option will now  • 
open.
ENTER
POSITION
SHIFT
ASPECT
ZOOM
CLOCK PHASE
GEOMETORY
 MENU SELECT
 SUB MENUDEFAULT
0
OFF
Press ▲▼ button to highlight the  4. 
desired adjustment item, then 
press ◄► to change or adjust 
the parameter value.
For some items, an individual adjustment  • 
screen containing a bar scale will appear as 
shown in the diagram below when ◄► is 
pressed.
CONTRAST
 ADJUST0
If no button is pressed for approx. 5 seconds  • 
while the individual adjustment screen is 
displayed, the screen will return to the previous 
page.
Returning to the previous screen  „
When the “MENU” is on the screen, pressing  • 
the MENU button returns to the previous page.
When the “MAIN MENU” is on the screen,  • 
pressing MENU clears all menus from the 
screen.
Menu items setting  „
The bottom prompt line differs on each menu  • 
depending on the selected menu option:
A prompt “◄► CHANGE” appears when  • 
changing the setting.
A prompt “◄► ADJUST” appears for a  • 
separate bar graph.
If there are more adjustments (items) available  • 
for a menu item, a page number will appear at 
the top-right of the screen.
Resetting to the factory 
default
If an adjustment item is selected and DEFAULT 
is pressed, the adjustment value will return to the 
factory default setting.
Press DEFAULT. 1. 
ENTER
PICTURE
PICTURE MODE
 CONTRAST
 BRIGHTNESS
 COLOR
 TINT
 COLOR TEMPERATURE
 GAMMA
 SYSTEM DAYLIGHT VIEW
 SHARPNESS
 NOISE REDUCTION
 DYNAMIC IRIS
SYSTEM SELECTOR
 MENU SELECT
 CHANGE REGISTERSTANDARD
0
0
0
0
DEFAULT
DEFAULT
OFF
0
OFF
OFF
AUTO1 
						

							54 – ENGLISH
Adjusting the picture
 
Switching the picture mode
The user can switch to the desired picture mode 
suitable for the image source and the environment in 
which this projector is used.
Press ▲▼ to select “PICTURE  1. 
MODE”.
PICTURE
PICTURE MODE
 CONTRASTSTANDARD
0
Press ◄► to switch “PICTURE  2. 
MODE”.
The setting will change as follows each time  • 
◄► is pressed.
STANDARD
USER
CINEMA
GRAPHIC
NATURAL
DYNAMIC
STANDARD: • 
The picture becomes suitable for moving images in 
general.
CINEMA: • 
The picture becomes suitable for movie sources.
NATURAL: • 
The picture complies with sRGB.
DYNAMIC: • 
The light output is maximized for use in bright 
areas.
GRAPHIC: • 
The picture becomes suitable for input from to the 
personal computer.
USER: • 
The COLOR TEMPERATURE and GAMMA settings 
can be adjusted.
Note
Factory defaults are “GRAPHIC” for RGB system  • 
and “STANDARD” for moving images.
When ENTER is pressed while “PICTURE MODE”  • 
has been selected, the current Picture Mode page 
settings are saved and will be used as the presets 
when new signals are input. The data will be saved 
for all items in the PICTURE menu except for the 
SYSTEM SELECTOR setting.
  Adjusting Contrast
Adjusts the Contrast (white level).
Press ▲▼ to select  1. 
“CONTRAST”.
PICTURE MODE
 CONTRAST
 BRIGHTNESSSTANDARD
0
0
▲▼◄►
ENTER
DEFAULT MENU
You can adjust pictures to suit your preference.
MENUPress to display the MAIN 
MENU screen.
Press to select 
“PICTURE”.
Press to display the 
“PICTURE” menu.
ENTER
MAIN MENU
 PICTURE
 POSITION
 ADVANCED MENU
 DISPLAY LANGUAGE
 DISPLAY OPTION
 PROJECTOR SETUP
  P IN P
 TEST PATTERN
 SIGNAL LIST
 SECURITY
 NETWORK
 MENU SELECT
 SUB MENU
Some menu items may not be valid for certain  • 
signal formats applied to the projector. 
						

							ENGLISH – 55
Basic Operation
Press ◄► or ENTER. 2. 
The “CONTRAST” individual adjustment screen  • 
will be displayed.
CONTRAST
 ADJUST0
Press ◄► to adjust the level. 3. 
Operation AdjustmentAdjustment 
range
Press ► 
button.
Raises the picture 
brightness and the 
picture becomes clearer.Maximum value 
31
Press ◄ 
button.Lowers the picture 
brightness and 
weakens the picture. Minimum value 
-31
Attention
If you need to adjust the “BRIGHTNESS”, it should  • 
be adjusted before other adjustments are made.
  Adjusting Brightness
Adjusts the brightness (black level) of the picture.
Press ▲▼ to select  1. 
“BRIGHTNESS”.
 CONTRAST
 BRIGHTNESS
 COLOR0
0
0
Press ◄► or ENTER. 2. 
The “BRIGHTNESS” individual adjustment  • 
screen will be displayed.
BRIGHTNESS
 ADJUST0
Press ◄► to adjust the level. 3. 
Operation AdjustmentAdjustment 
range
Press ► 
button.Increases the 
brightness of the dark 
(black) parts of the 
screen.Maximum value 
31
Press ◄ 
button.Reduces the brightness 
of the dark (black) parts 
of the screen.Minimum value 
-31
  Adjusting Color
This adjusts the depth of the colors.
Press ▲▼ to select “COLOR”. 1. 
 BRIGHTNESS
 COLOR
 TINT0
0
0
Press ◄► or ENTER. 2. 
The “COLOR” individual adjustment screen will  • 
be displayed.
COLOR
 ADJUST0
Press ◄► to adjust the level. 3. 
Operation AdjustmentAdjustment 
range
Press ► 
button.Deepens colors.Maximum value 
50
Press ◄ 
button.Weakens colors.Minimum value 
-50
  Adjusting Tint
This adjusts skin tones in the pictures.
Press ▲▼ to select “TINT”. 1. 
 COLOR
 TINT
 COLOR TEMPERATURE0
0
DEFAULT
Press ◄► or ENTER. 2. 
The “TINT” individual adjustment screen will be  • 
displayed.
TINT
 ADJUST0
Press ◄► to adjust the level. 3. 
Operation AdjustmentAdjustment 
range
Press ► 
button.Adjusts skin tone 
toward reddish-purple.Maximum value 
31
Press ◄ 
button.Adjusts skin tone 
toward greenish color.Minimum value 
-31
  Adjusting the color 
temperature
Used to set the projector’s white point. Three presets 
and two user-definable modes are available. A 
colorimeter should be used if available.
Carry out this adjustment while the signals to be  • 
adjusted are being projected.
Press ▲▼ to select “COLOR  1. 
TEMPERATURE”.
 TINT
 COLOR TEMPERATURE
 GAMMA0
DEFAULT
DEFAULT
Press ◄► or ENTER. 2. 
The “COLOR TEMPERATURE” individual  • 
adjustment screen will be displayed.
COLOR TEMPERATURE
 CHANGEDEFAULT 
						

							56 – ENGLISH
Adjusting the picture (continued)
Press ◄► to switch “COLOR  3. 
TEMPERATURE”.
The setting will change as follows each time  • 
◄► is pressed.
DEFAULT
HIGH
USER1
MIDDLE
USER2
LOW
When any setting other than “OFF” has been  • 
selected for color matching, the COLOR 
TEMPERATURE setting is fixed at “USER1”.
“DEFAULT” cannot be selected when the picture  • 
mode has been set to “USER”.
To further adjust toward the   „
desired white balance
Select “USER1” or “USER2” in  4. 
Step 3.
Press ENTER. 5. 
The “WHITE BALANCE” screen will be  • 
displayed.
WHITE BALANCE
WHITE BALANCE HIGH
WHITE BALANCE LOW
Press ▲▼ to select “WHITE  6. 
BALANCE HIGH” or “WHITE 
BALANCE LOW”.
Press ENTER. 7. 
The “WHITE BALANCE HIGH” RGB settings  • 
are used to set the projector’s white point color 
temperature. The “WHITE BALANCE LOW” 
RGB settings are used to adjust the color 
temperature of the black levels.
WHITE BALANCE HIGH
RED
GREEN
255
255
Press ▲▼ to select “RED”,  8. 
“GREEN” or “BLUE”.
Press ◄► to adjust the level. 9. 
Item Operation AdjustmentAdjustment 
range
REDPress ► 
button.Deepens red.Maximum 
value
HIGH : 255
LOW : 127
Minimum 
value
HIGH : 0
LOW : -127
Default
HIGH : 255
LOW : 0 Press ◄ 
button.Weakens red.
GREENPress ► 
button.Deepens green.
Press ◄ 
button.Weakens green.
BLUEPress ► 
button.Deepens blue.
Press ◄ 
button.Weakens blue.
Note
All colors will not be displayed properly unless  • 
adequate adjustment is made. If the adjustment 
does not look suitable, you can press DEFAULT to 
return the setting for the selected item only to the 
factory default setting.
The color temperature cannot be adjusted for the  • 
internal test pattern (p. 87). Be sure to project the 
input signal when adjusting the color temperature.
  Gamma setting
This switches the gamma mode.
Press ▲▼ to select “GAMMA”. 1. 
 COLOR TEMPERATURE
 GAMMA
 SYSTEM DAYLIGHT VIEWDEFAULT
DEFAULT
OFF
Press ◄► or ENTER. 2. 
The “GAMMA” individual adjustment screen  • 
will be displayed.
GAMMA
 CHANGEDEFAULT
Press ◄► to switch “GAMMA”. 3. 
The setting will change as follows each time  • 
◄► is pressed.
DEFAULT
2.6
USER1*
2.5
USER2*
2.2
*  “USER1” and “USER2” can hold user-defined 
gamma curves uploaded to the projector through 
the RS-232 terminal.
Additional Gamma settings can be made available 
for selection from a sub-menu.
Consult your dealer for more information.
Note
“DEFAULT” cannot be selected when the picture  • 
mode has been set to “USER”.
 System daylight view setting
This corrects images so that they appear vivid when 
projected under bright lighting.
Press ▲▼ to select “SYSTEM  1. 
DAYLIGHT VIEW”.
 GAMMA
  SYSTEM DAYLIGHT VIEW
 SHARPNESSDEFAULT
OFF
0
Press ◄► or ENTER. 2. 
The “SYSTEM DAYLIGHT VIEW” individual  • 
adjustment screen will be displayed.
SYSTEM DAYLIGHT VIEW
 CHANGEOFF 
						

							ENGLISH – 57
Basic Operation
Press ◄► to switch “SYSTEM  3. 
DAYLIGHT VIEW”.
The setting will change as follows each time  • 
◄► is pressed.
3 (High)
OFF (No correction)
2 (Medium)
1 (Low)
 
Sharpness setting
This adjusts the sharpness of the pictures.
Press ▲▼ to select  1. 
“SHARPNESS”.
 SYSTEM DAYLIGHT VIEW
 SHARPNESS
 NOISE REDUCTIONOFF
0
OFF
Press ◄► or ENTER. 2. 
The “SHARPNESS” individual adjustment  • 
screen will be displayed.
SHARPNESS
 ADJUST0
Press ◄► to adjust the level. 3. 
Operation AdjustmentAdjustment 
range
Press ► 
button.Contours become 
sharper.
0 to 15
Press ◄ 
button.Contours become 
softer.
Note
The possible setting range will vary depending on  • 
the input signal.
  Noise reduction setting
This can be used to adjust pictures if they contain 
interference as a result of poor quality of the input 
signal.
Press ▲▼ to select “NOISE  1. 
REDUCTION”.
 SHARPNESS
 NOISE REDUCTION
 DYNAMIC IRIS0
OFF
OFF
Press ◄► or ENTER. 2. 
The “NOISE REDUCTION” individual  • 
adjustment screen will be displayed.
NOISE REDUCTION
 CHANGEOFF
Press ◄► to switch “NOISE  3. 
REDUCTION”.
The setting will change as follows each time  • 
◄► is pressed.
2 (Medium)
1 (Low)
3 (High)
OFF (No correction)
Note
When “FRAME DELAY” is set to “SHORT”, the  • 
noise reduction setting function cannot be used.
  Dynamic iris setting
Pictures with the optimum contrast will be displayed 
by automatically providing aperture compensation 
and signal compensation to suit the pictures 
concerned.
Press ▲▼ to select “DYNAMIC  1. 
IRIS”.
 NOISE REDUCTION
 DYNAMIC IRIS
SYSTEM SELECTOROFF
OFF
AUTO1
Press ◄► or ENTER. 2. 
The “DYNAMIC IRIS” individual adjustment  • 
screen will be displayed.
DYNAMIC IRIS
 CHANGEOFF
Press ◄► to switch “DYNAMIC  3. 
IRIS”.
The setting will change as follows each time  • 
◄► is pressed.
2 (Intermediate)
1 (Low)
USER3 (High)
OFF (No correction)
To further adjust the selected   „
compensation amount
Select “USER” in step 3. 4. 
Press ENTER. 5. 
The “DYNAMIC IRIS” screen will be displayed. • 
DYNAMIC IRIS
AUTO IRIS
MANUAL IRIS
DYNAMIC GAMMAOFF
OFF
OFF
Use ▲▼ to select the item to be  6. 
adjusted, and then use ◄► to 
adjust the amount of correction. 
						

							58 – ENGLISH
Adjusting the picture (continued)
AUTO IRIS (Automatic aperture   „
adjustment)
OFF (No automatic 
adjustment)
3 (High)
1 (Low)
2 (Intermediate)
MANUAL IRIS (Fixed aperture   „
adjustment)
OFF (No fixed iris)
63 (High)
1 (Low)
2œ62 (Intermediate)
DYNAMIC GAMMA (signal   „
compensation amount 
adjustment)
OFF (No automatic 
correction)
3 (High)
1 (Low)
2 (Intermediate)
Note
The contrast is set to the maximum level when  • 
“DYNAMIC IRIS” is set to “3”.
  Registering the picture mode 
settings as presettings
The picture settings that have been made in the 
PICTURE MODE screen can be registered.
Select “PICTURE MODE” in the “PICTURE” screen  • 
to carry out this operation.
Press ENTER. 1. 
A confirmation screen will appear. • 
ENTER
OKCANCEL SAVE AS DEFAULT SETTING
FOR DYNAMIC?

CHANGE

EXECUTE
Press ◄► to select “OK”. 2. 
Press ENTER. 3. 
Note
If the registered picture mode is selected after  • 
registering the picture mode settings as presettings, 
the new signals will be displayed with the registered 
adjustments.
Setting the  system selector
This enables the projector to automatically recognize 
input signals. Furthermore, if unstable signals are 
input, the system format can be selected manually.
Press ▲▼ to select “SYSTEM  1. 
SELECTOR”.
 NOISE REDUCTION
 DYNAMIC IRIS
SYSTEM SELECTOROFF
OFF
AUTO1
Press ENTER. 2. 
The “SYSTEM SELECTOR” screen will be  • 
displayed.
SYSTEM SELECTOR
C AUTO1
 AUTO2
Press ▲▼ to switch “SYSTEM  3. 
SELECTOR”, and then press 
ENTER.
The system formats that can be selected differ  • 
depending on the input signals.
S-video / Video terminal input   „
signal
Select from AUTO1, AUTO2, NTSC, NTSC4.43, 
PAL, PALM, PAL-N, SECAM, and PAL60.
Note
Press the DEFAULT button to return to “AUTO1”. • 
“AUTO1” automatically selects from NTSC,  • 
PAL, SECAM, NTSC4.43, and PAL60. “AUTO2” 
automatically selects from NTSC, PAL-M, and 
PAL-N.
RGB1 / RGB2 / DVI-D terminal   „
input signal
Select from RGB and YPBPR.
Note
Refer to the types of signals compatible with the  • 
projector. (pp. 122-123)
Input module  „
ET-MD77SD1:
Select from AUTO, 480i and 576i.
ET-MD77SD3:
Select from AUTO, 1 080/60i, 1 035/60i, 720/60p, 
1 080/24p, 1 080/50i, 1 080/30p, 1 080/25p, 
1 080/24sF, 720/50p, and 480i, 576i. 
						

							ENGLISH – 59
Basic Operation
ET-MD100SD4:
When single link SDI signals
Select from AUTO YCbCr, 1 080/60i, 1 035/60i, 
720/60p, 1 080/24p, 1 080/50i, 1 080/30p, 
1 080/25p, 1 080/24sF, 720/50p, 480i, and 576i.
When dual link SDI signals
Select from AUTO RGB, AUTO X’Y’Z’, 
1 920/24p/RGB, 2 048/24p/RGB, 2 048/24p/XYZ, 
1 920/24sF/RGB, 2 048/24sF/RGB, 2 048/24sF/
XYZ, 1 920/25p/RGB, 1 920/30p/RGB, 1 920/50i/
RGB, and 1 920/60i/RGB.
Note
Press the DEFAULT button to return to AUTO  • 
YCbCr or AUTO RGB.
“AUTO RGB” automatically selects from 1 920/24p/ • 
RGB, 2 048/24p/RGB, 1 920/24sF/RGB, 
2 048/24sF/RGB, 1 920/25p/RGB, 1 920/30p/RGB, 
1 920/50i/RGB, and 1 920/60i/RGB. “AUTO X’Y’Z’” 
automatically selects from 2 048/24p/XYZ and 
2 048/24sF/XYZ.
To display pictures complying 
with the  sRGB standard
sRGB is the international color reproduction standard 
(IEC61966-2-1) established by IEC (International 
Electrotechnical Commission).
To reproduce colors more faithfully in compliance 
with the sRGB standard, perform the following setting 
procedure.
Set “COLOR MATCHING”  1. 
adjustment to “OFF”. (p. 70)
Display the “PICTURE” screen.  2. 
(p. 54)
Press ▲▼ to select “PICTURE  3. 
MODE”.
PICTURE
PICTURE MODE
 CONTRASTNATURAL
0
Press ◄► to select “NATURAL”. 4. 
Press ▲▼ to select  “COLOR”. 5. 
 BRIGHTNESS
 COLOR
 TINT0
0
0
Press DEFAULT on the remote  6. 
control to restore the factory 
default.
Follow the same procedure  7. 
(steps 5-6) to restore the factory 
default for “TINT”, “COLOR 
TEMPERATURE” and “GAMMA”.
Note
sRGB is only enable when RGB signals are being  • 
input. 
						

							60 – ENGLISH
Adjusting the position
 
Shift adjustment
This function allows the user to adjust the raster 
position vertically or horizontally if the position of 
the image projected on the screen is displaced 
even when the projector is properly aligned with the 
screen, and the internal test patterns are correctly 
framed.
Press ▲▼ to select  “SHIFT”. 1. 
POSITION
SHIFT
ASPECT
DEFAULT
Press ENTER. 2. 
The “SHIFT” screen will be displayed. • 
SHIFT
V
H12
212
Press ▲▼◄► to adjust the  3. 
position.
For horizontal (right and left) 
  „
adjustment
Operation Adjustment
Press ► button.The picture 
position moves 
to the right.
Press ◄ button.The picture 
position moves 
to the left.
For vertical (up and down)   „
adjustment
Operation Adjustment
Press ▲ button.The picture 
position moves 
up.
Press ▼ button.The picture 
position moves 
down.
Press MENU three times. 4. 
The on-screen indications disappear and the  • 
normal screen appears again.
▲▼◄►
ENTER
DEFAULT MENU
You can adjust the position as required.
MENUPress to display the MAIN 
MENU screen.
Press to select 
“POSITION”.
Press to display the 
“POSITION” menu.
ENTER
MAIN MENU
 PICTURE
 POSITION
 ADVANCED MENU
 DISPLAY LANGUAGE
 DISPLAY OPTION
 PROJECTOR SETUP
  P IN P
 TEST PATTERN
 SIGNAL LIST
 SECURITY
 NETWORK
 MENU SELECT
 SUB MENU