Panasonic Projector Pt D10000e Operating Instructions

ENGLISH – 11
Getting Started
Do not place the projector over 2 700 m above sea level. When using it 
over 1 400 m above sea level, set the “
ALTITUDE”, described on page 76, 
to “
HIGH”.
Otherwise the life of the product may be shortened.
Do not install the projector vertically facing downward. 
If the projector is installed vertically facing downward or at a 45° angle at the front or rear, the lamp unit will not 
cool down correctly and this will shorten the operating life of the lamp and the...

12 – ENGLISH
Location and function of each part
Front■
Remote control unit
#  Remote control operation indicator lamp
The lamp flashes when any remote control button 
is pressed.
$ POWER 
STANDBY button ................. (pp. 34, 36)
When the projector is in projection mode with the 
MAIN POWER switch of the projector at the “ l ” 
side, this button switches the projector to standby 
mode.
%  POWER ON button ............................. (
pp. 34, 35)
When the projector is in standby mode with the 
MAIN...

ENGLISH – 13
Getting Started
1 SHUTTER button ........................................ (p. 43)
Press this button to black out the image 
temporarily.
2 ASPECT button ........................................... (
p. 45)
Switches the image aspect ratio.
3  LENS (FOCUS, ZOOM, SHIFT) button ...... (
p. 37)
These buttons are used to adjust the projection 
lens. 
4  Function 1 (FUNC1) button ........................ (
p. 44)
This button can control the functions set in 
“
FUNC1” of the “OPTION1” screen from...

14 – ENGLISH
Front■
Projector Main Unit
Location and function of each part (continued)
Rear■
$%&()
*+-. / 01
#  Projectin lens cover ................................... (p. 33)
$  Projection lens (optional)
Lens for projecting images on the screen.
%  Remote control receiver window (front) .. (
p. 17)
This window receives the signal beam emitted from 
the remote control.
& 
LAMP (LAMP1, LAMP2, LAMP3, LAMP4) 
monitor
 ...................................................... (p. 107)
These light when it is...

ENGLISH – 15
Getting Started
Controls■Side■
#$% 12&( ) * + -
./0
#  AC IN terminal ............................................. (
p. 34)
Connect the supplied line power cord into this 
receptacle.
Do not connect any other cable to this socket.
$  MAIN POWER switch ......................... (
pp. 35, 36)
Use this switch to turn on “I” and off “○” the 
commercial line power applied to the projector.
% Slot cover .................................................... (
p. 28)
Install the input module here.
&...

16 – ENGLISH
#  REMOTE1 lN/OUT terminal ........................(p. 18)
When two or more main units are used in the 
system, they can be connected and controlled with 
a wired remote control cable (M3 jack).
$  REMOTE2 IN terminal ..............................(
p. 106)
The user can remotely control the main unit by 
using an external control circuit to this terminal 
(D-SUB 9-pin female).
%  SERIAL IN terminal ....... (
pp. 25, 26, 79, 102-105)
This terminal is an RS-232C compliant input 
terminal...

ENGLISH – 17
Getting Started
Loading batteries
When loading supplied AA batteries into the battery 
compartment of the Remote Control, make sure that 
their polarities are correct.
1.  Open battery compartment lid.
Open the lid in the order # and then $.
2. Insert the batteries.
Into battery compartment, with their polarities 
orientated as indicated (
+, –) in the 
compartment.
3.  Close the battery compartment 
lid.
Replace the battery compartment lid over the 
compartment and slide until it clicks....

18 – ENGLISH
Note
The Remote Control may not function properly if an 
object is in the light path.
The Remote Control receiver may not function 
properly in intense ambient light such as fluorescent 
lamps. Carefully site the projector so its Remote 
Control receiver windows will not be directly 
exposed to intense light.
  Setting projector ID 
number to remote control
Every projector has its ID number and the ID number 
of the controlling projector must be set to the remote 
control in advance so that...

ENGLISH – 19
Getting Started
Examples of system expansion
The projector is provided with a number of terminals and optional accessories to enable various system 
expansions. Both input and output are provided to all terminals on the main unit.
The following are some examples of system expansion:
Installation
System 1
The optional high- or low-ceiling mount bracket flexibly fits the projector in 
individual site conditions.
System 2
Connection to a computer via the DVI-D IN terminal or DVI-D input module...

20 – ENGLISH
 
Adjusting the feet
The four adjustable feet mounted at the bottom of the projector are level-adjustable (0 mm–15 mm) which can be 
used when the floor surface is not horizontal.
  Projection scheme
This projector can use any of the four projection schemes. Select the most suitable scheme to the situation of your 
location. Use the OPTION menu on the menu screen to choose the desired projection scheme. (
p. 76)
Installation geometry
When planning the projector and screen geometry, refer to...