Panasonic Projector Pt Ae900u Operating Instructions

ENGLISH
-21
Getting started
20-E
NGLISH
Setting up range using the lens shift functionThis projector can be placed in various places by controlling the shift lever at
the front side of the projector to move the lens in order to adjust the position
of the projected image.
BVertical lens shift
When shift lever is
moved down (full)
When shift lever is
moved up (full)
NOTE:
BTurn the shift lever right to secure the shift lever.
BWhen the lens has been shifted fully to the right or left, you will not be
able...

ENGLISH
-23
Getting started
22-E
NGLISH
Connecting to video equipment
NOTE:
BBe sure to use an HDMI cable which conforms to HDMI specifications. 
If inappropriate cables are used, the connected equipment may not
operate correctly.
B
This projector can be connected to HDMI and DVI equipment, but some
equipment may not operate correctly, for example images may not appear
.
ConnectionsNotes on connectionsB
Read the instruction manual for each peripheral device carefully before connecting it.
B
Turn off the...

ENGLISH
-25
Getting started
24-E
NGLISH
To RGB output
Operating rangeIf the remote control unit is held so that it is facing directly in front of the remote
control signal receptor, the operating range is within approximately 7 m (23´) from
the surfaces of the receptor. Furthermore, the remote control unit can be operated
from an angle of ±30° to the left or right and ±15° above or below the receptor
. #Open the cover.
$Insert the batteries so that the polarities are correct, and then close
the cover....

ENGLISH
-27
Basic operation
Press the input select button to select the input signal.BA picture will be projected in accordance with the selected input signal.
Follow the procedure below when you set the projector up first, and when
you change the setup place.&
Input select
button
Changing
signals
Input select
button
Changing
signals Control 
panel
Remote
control 
unit
VIDEO
S-VIDEO
YP
BPR1
HDMI
YP
BPR2
PC
VIDEOS-VIDEO
YP
BPR1
YP
BPR2
PCHDMI
˛ $
˛ &
˛ (˛ '
˛ ( ˛ *
˛ )
˛
#
Turning on the powerBefore...

ENGLISH
-29
Basic operation
28-E
NGLISH
NOTE:
BDuring projection of an image, the cooling fan will operate, emitting a
small noise as it operates. This noise may change depending on the
ambient temperature. Turning the lamp on or off will cause this noise to
increase a little.
BBy using the “OPTION” menu to set “LAMP POWER” to “LOW”, the
operating sound of the fan can be reduced. (Refer to page 53.)
BYou can also turn off the power by pressing the POWER button twice or
by holding it down for at least 0.5...

ENGLISH
-31
Useful functions
30-E
NGLISH
Setting the aspect ratio (ASPECT)This projector allows you to change the aspect ratio to match the type of
input signal.
JUST\
4:3\
16:9\
14:9\
ZOOM1\
ZOOM2
4:3\
16:9\
V SCROLL
*“V SCROLL” cannot be set when a VGA or
SVGA signal is being input.
4:3\
16:9
[When a 525p (480p) or 625p (576p) signal is
being input]
4:3\
16:9\
JUST\
ZOOM [When an NTSC, 525i (480i) or 525p (480p)
YP
BPRsignal is being input]
AUTO\
4:3\
16:9\
JUST\
ZOOM
S-VIDEO/VIDEO/
YP
BPR1/YP
BPR2
PC...

ENGLISH
-33
Useful functions
32-E
NGLISH
Turning on the button lights (LIGHT)
Press the LIGHT button.
BThe buttons on the remote control unit will be
illuminated.
BPress the LIGHT button again to turn off the
button lights. The button lights will be turned off
automatically when no buttons on the remote
control unit are pressed for 10 seconds.
NOTE:
BThe picture mode can also be selected from “PICTURE MODE” in the
“PICTURE” menu.
B
When the 
“PICTURE MODE
”menu is selected, the settings will switch...

ENGLISH
-35
Useful functions
34-E
NGLISH
NOTE:
BOnly the settings saved in the “MEMORY SAVE” menu will be
displayed in the “MEMORY LOAD” menu. (Refer to page 47.) BThe “MEMORY LOAD” menu will be displayed.
BPress the For Gbutton to select the setting
you want to retrieve, then press the ENTER
button.Retrieving the saved picture
settings (MEM. LOAD)If you have saved the adjusted picture settings using the “MEMORY SAVE”
menu, you can retrieve the saved picture settings.
Press the MEM. LOAD button.Turning...

ENGLISH
-37
Useful functions
36-E
NGLISH
CURSORYou can select a color in the projected image, and adjust the color settings.
Press the ENTER button to display the cursor (
B).
#Select the color you want to adjust with the cursor.
BPress the F, G, Iand Hbuttons to move the cursor, and then press
the ENTER button.
BThe selected color (
C) and the “CURSOR” menu (
A) will be displayed.
$Adjust the items in the “CURSOR” menu.
BThe color adjusted in the “CURSOR” menu (
D) will be displayed. 
COLORAdjusts the...

ENGLISH
-39
Useful functions
38-E
NGLISH
NOTE:
BAfter saving the adjusted settings, the “PROFILE” setting will
automatically change to the setting saved in the “PROFILE SAVE”
menu. If you continue to adjust colors to make other profiles, change
the “PROFILE” setting to “NORMAL” manually.
BWhen the “COLOR MANAGEMENT” menu is closed, or if the “PROFILE”
settings are changed before the adjusted color settings have been saved,
the “PROFILE SAVE” confirmation screen will be displayed. However, if
you change...