Panasonic Projector Pt Ae900u Operating Instructions

							ENGLISH
TQBJ 0182
LCD Projector 
Operating Instructions
Model No.
PT-AE900U
R
Before operating this product, please read the instructions carefully an\
d save this
manual for future use.For assistance, please call : 1-888-View-PTV(843-9788) or send e-mail to : [email protected]
or visit us at www.panasonic.com (U.S.A)
For assistance, please call : 787-750-4300 or visit us at www.panasonic.co.jp/global/ (Puerto Rico) 
						

							2-E
NGLISH
IMPORTANT SAFETY NOTICE Dear Panasonic Customer:This instruction booklet provides all the necessary operating information that
you might require. We hope it will help you to get the most out of your new
product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should
note it in the space provided below and retain this booklet in case service is
required.Model number:  PT-AE900USerial number:
ENGLISH
-3
Preparation
WARNING: 
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
Power Supply:This LCD Projector is designed to operate on 100 V – 240 V, 50 Hz/60
Hz AC, house current only.
CAUTION:The AC power cord which is supplied with the projector as an accessory can
only be used for power supplies  up to 125 V, 7 A. If you need to use higher
voltages or currents than this, you will need to obtain a separate 250 V
power cord. If you use the accessory cord in such situations, fire may result.
CAUTION:
This equipment is equipped with a three-
pin grounding-type power plug. Do not
remove the grounding pin on the power
plug. This plug will only fit a grounding-
type power outlet. This is a safety feature.
If you are unable to insert the plug into
the outlet, contact an electrician. Do not
defeat the purpose of the grounding plug.
WARNING:This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
–  Reorient or relocate the receiving antenna.
–  Increase the separation between the equipment and receiver.
–  Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
–  Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION:To assure continued compliance, use only shielded interface cables when
connecting to computers or peripheral devices. 
Any unauthorized changes or modifications to this equipment will void the
users authority to operate.
If you use serial port to connect PC for external control of projector, you
must use optional RS-232C serial interface cable with ferrite core. Any
unauthorized changes or modifications to this equipment will void the
user’s authority to operate.
Do not remove 
						

							ENGLISH
-5
Preparation
4-E
NGLISH
ContentsPreparationIMPORTANT SAFETY NOTICE ...2
Precautions with regard to 
safety .........................................6
Accessories ...............................10
Before use ..................................11
Location and function of each
part ...........................................13Getting startedSetting-up ...................................18
Projection methods, Projector
position, Projection distances,
Setting up range using the lens shift
function
Connections ...............................22
Connecting to video equipment,
Connecting to equipment
compatible with HDMI, 
Connecting to computer
Preparation for the remote
control unit ..............................25Basic operationTurning on the power ................26
Turning off the power................28Useful functionsSetting the aspect ratio .............30
Selecting the picture mode.......33
Turning on the button lights.....33
Retrieving the saved picture
settings ....................................34Turning off the picture momentarily
...34
Displaying the “PICTURE” menu
.....35
Displaying the “ADVANCED MENU”
...35
Using the Cinema Color
Management function ............36
Adjustments and settingsOn-screen menus ......................40
Menu screens, Menu operation
guide, Returning a setting to the
factory default
Adjusting the picture.................44
PICTURE MODE, CONTRAST,BRIGHT, COLOR, TINT,
SHARPNESS, COLOR TEMP., 
DYNAMIC IRIS, Noise
Reduction(NR), CINEMA REALITY,
TV-SYSTEM, ADVANCED MENU, 
MEMORY SAVE, MEMORY LOAD,
SIGNAL MODE, 
Projecting sRGB-
compatible pictures
Adjusting the position...............48
Horizontal position, Vertical position,
DOT CLOCK, CLOCK PHASE,
ASPECT, WSS, OVER SCAN,
KEYSTONE, AUTO SETUPChanging the display language
...50
Option settings ..........................51
OSD, OSD DESIGN, OSD
POSITION, AUTO SEARCH, BACK
COLOR, STARTUP LOGO,
DESK/CEILING, FRONT/REAR,
OFF TIMER, FAN CONTROL,
LAMP POWER, LAMP RUNTIME
Care and maintenanceWhen the TEMP indicator and the
LAMP indicator are illuminated
...54
Cleaning and replacing 
the air filter ..............................56
Replacing the lamp unit ............57
Before calling for service..........60
Cleaning and maintenance .......61
OthersSpecifications ............................62
Appendix ....................................64
List of compatible signals, General
arrangement of the “COLOR
MANAGEMENT” menu, Using the
SERIAL connector, Projection
dimensions calculation methods 
Dimensions ................................69Trademark acknowledgements
...70
Declaration of Conformity
Model Number:  PT-AE900U
Trade Name:Panasonic
Responsible party:  Panasonic Corporation of North America.
Address:  One Panasonic Way Secaucus New Jersey 07094
Telephone number:  1-888-View-PTV(843-9788)
This device complies with Part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING:
Not for use in a computer room as defined in the Standard for the Protection
of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. 
						

							ENGLISH
-7
Preparation
6-E
NGLISH
Precautions with regard to safetyWARNINGIf you notice smoke, strange smells or noise coming from the projector,
disconnect the power cord plug from the wall outlet.
BDo not continue to use the projector in such cases, otherwise fire or
electric shocks could result.
BCheck that no more smoke is coming out, and then contact an Authorized
Service Center for repairs.
BDo not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place which is not strong enough to
take the full weight of the projector.
BIf the installation location is not strong enough, it may fall down or tip over,
and severe injury or damage could result.
Installation work (such as ceiling suspension) should only be carried
out by a qualified technician.
BIf installation is not carried out correctly, there is the danger that injury or
electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is
dropped or the cabinet is broken, disconnect the power cord plug from
the wall outlet.
BContinued use of the projector in this condition may result in fire or electric
shocks.
BContact an Authorized Service Center for repairs.
Do not overload the wall outlet.
BIf the power supply is overloaded (for example, by using too many
adapters), overheating may occur and fire may result.
Do not remove the cover or modify it in any way.
BHigh voltages can cause fire or electric shocks.
BFor any inspection, adjustment and repair work, please contact an
Authorized Service Center.
Clean the power cord plug regularly to prevent it from becoming
covered in dust.
BIf dust builds up on the power cord plug, the resulting humidity can
damage the insulation, which could result in fire. Pull the power cord plug
out from the wall outlet and wipe it with a dry cloth.
BIf not using the projector for an extended period of time, pull the power
cord plug out from the wall outlet.Do not do anything that might damage the power cord or the power
cord plug.
BDo not damage the power cord, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
BIf the power cord is used while damaged, electric shocks, short-circuits or
fire may result.
BAsk an Authorized Service Center to carry out any repairs to the power
cord that might be necessary.
Do not handle the power cord plug with wet hands.
BFailure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
BIf the plug is not inserted correctly, electric shocks or overheating could
result.
BDo not use plugs which are damaged or wall outlet which are coming
loose from the wall.
Do not place the projector on top of surfaces which are unstable.
BIf the projector is placed on top of a surface which is sloped or unstable, it
may fall down or tip over, and injury or damage could result.
Do not place the projector into water or let it become wet.
BFailure to observe this may result in fire or electric shocks.
Do not place liquid containers on top of the projector.
BIf water spills onto the projector or gets inside it, fire or electric shocks
could result.
BIf any water gets inside the projector, contact an Authorized Service
Center.
Do not insert any foreign objects into the projector.
BDo not insert any metal objects or flammable objects into the projector or
drop them onto the projector, as doing so can result in fire or electric
shocks.
Do not allow the + and - terminals of the batteries to come into contact
with metallic objects such as necklaces or hairpins.
BFailure to observe this may cause the batteries to leak, overheat, explode
or catch fire.
BStore the batteries in a plastic bag and keep them away from metallic
objects.
During a thunderstorm, do not touch the projector or the cable.
BElectric shocks can result.
Do not use the projector in a bath or shower.
BFire or electric shocks can result. 
						

							ENGLISH
-9
Preparation
8-E
NGLISH
Do not look into the lens while the projector is being used.
BStrong light is emitted from the projector’s lens. If you look directly into this
light, it can hurt and damage your eyes.
BBe especially careful not to let young children look into the lens. In
addition, turn off the power and disconnect the power cord plug when you
are away from the projector.Do not place your skin into the light beam while the projector is being used.BStrong light is emitted from the projector’s lens. If you place directly into
this light, it can hurt or damage your skin.
Do not place your hands or other objects close to the air outlet port.
BHeated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port [allow at
least 10cm (4”) of space], otherwise burns or damage could result.
Replacement of the lamp should only be carried out by a qualified
technician.
BThe lamp has high internal pressure. If improperly handled, explosion
might result.
BThe lamp can easily become damaged if struck against hard objects or
dropped, and injury or malfunctions may result.
When replacing the lamp, allow it to cool for at least one hour before
handling it.
BThe lamp cover gets very hot, and touching it can cause burns.
Before replacing the lamp, be sure to disconnect the power cord plug
from the wall outlet.
BElectric shocks or explosions can result if this is not done.
Do not allow infants or pets to touch the remote control unit.
BThe accessory remote control unit can be used to operate not only the
projector but also other appliances such as air conditioners and electrical
device by programming them using the learning function. If the remote
control unit operated inappropriately, fire or injury may result.
BKeep the remote control unit out of the reach of infants and pets after
using it.CautionDo not cover the air inlet port or the air outlet port.
BDoing so may cause the projector to overheat, which can cause fire or
damage to the projector.
BDo not place the projector in narrow, badly ventilated places such as
closets or bookshelves.
Do not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.
BUsing the projector under such conditions may result in fire or electric
shocks.When disconnecting the power cord, hold the plug, not the cord.
BIf the power cord itself is pulled, the cord will become damaged, and fire,
short-circuits or serious electric shocks may result.
Always disconnect all cables before moving the projector.
BMoving the projector with cables still attached can damage the cables,
which could cause fire or electric shocks to occur.
Do not place any heavy objects on top of the projector.
BFailure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
Do not short-circuit, heat or disassemble the batteries or place them
into water or fire.
BFailure to observe this may cause the batteries to overheat, leak, explode
or catch fire, and burns or other injury may result.
When inserting the batteries, make sure the polarities (+ and -) are
correct.
BIf the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.
Use only the specified batteries.
BIf incorrect batteries are used, they may explode or leak, and fire, injury or
contamination of the battery compartment and surrounding area may
result.
Do not mix old and new batteries.
BIf the batteries are inserted incorrectly, they may explode or leak, and fire,
injury or contamination of the battery compartment and surrounding area
may result.
Do not put your weight on this projector.
BYou could fall or the projector could break, and injury may result.
BBe especially careful not to let young children stand or sit on the projector.
Disconnect the power cord plug from the wall outlet as a safety
precaution before carrying out any cleaning.
BElectric shocks can result if this is not done.
Ask an Authorized Service Center to clean inside the projector at least
once a year.
BIf dust is left to build up inside the projector without being cleaned out, it
can result in fire or problems with operation.
BIt is a good idea to clean the inside of the projector before the season for
humid weather arrives. Ask your nearest Authorized Service Center to
clean the projector when required. Please discuss with the Authorized
Service Center regarding cleaning costs.
We are constantly making efforts to preserve and maintain a clean
environment. Please take non repairable units back to your dealer or a
recycling company. 
						

							ENGLISH
-11
Preparation
10-E
NGLISH
AccessoriesCheck that all of the accessories shown below have been included with your
projector.
Before useCautions regarding setting-upAvoid setting up in places which are subject to vibration or shocks.
The internal parts can be damaged, which may cause malfunctions or
accidents.
Avoid setting up in places which are subject to sudden temperature
changes, such as near an air conditioner.
The life of the lamp may be shortened.
Do not set up the projector near high-voltage power lines or near
motors.
The projector may be subject to electromagnetic interference.
If installing the projector to the ceiling, ask a qualified technician to
carry out all installation work.
You will need to purchase the separate installation kit (Model No.ET-PKE300/
ET-PKE700). Furthermore, all installation work should only be carried out by a
qualified technician.
If using this projector at high elevations (above 1 400 m), set the “FAN
CONTROL” to “HIGH”. (Refer to page 53.)
Failure to observe this may result in malfunctions. NOTICE:
BThis product has a High Intensity Discharge (HID) lamp that contains a
small amount of mercury. It also contains lead in some components.
Disposal of these materials may be regulated in your community due to
environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries
Alliance: 
Remote control unit
(EUR7914Z20 x1)
AA batteries for remote control unit
(x2)
Power cord
(K2CG3FR00001 x 1) 
						

							ENGLISH
-13
Preparation
12-E
NGLISH
Notes on useIn order to get the best picture quality
Draw curtains or blinds over any windows and turn off any lights near the
screen to prevent outside light or light from indoor lamps from shining onto
the screen.
Do not touch the surfaces of the lens with your bare hands.
If the surface of the lens becomes dirty from fingerprints or anything else, this
will be magnified and projected onto the screen. Moreover, when not using
the projector, retract the lens and then cover it with the lens cover.
Screen
Do not apply any volatile substances which may cause discoloration to the
screen, and do not let it become dirty or damaged.
Lamp
The lamp may need to be replaced earlier due to variables such as individual
lamp characteristics, usage conditions and the installation environment,
especially when the projector is subjected to continuous use for more than
10 hours or the power is frequently turned on and off.
Liquid crystal panel
BDo not project the same image for long periods of time, as this may remain
as an afterimage on the liquid crystal panel.
BThe liquid crystal panel of the projector is built with very high precision
technology to provide fine picture details. Occasionally, a few non-active
pixels may appear on the screen as fixed points of blue, green or red.
Please note that this does not affect the performance of your LCD.
Location and function of each part#Projector control panel (page 16)
$Zoom ring (page 27)
%Focus ring (page 27)
&Projection lens
'Air inlet port
Do not cover this port.
(Air filter (page 56)
)Shift lever (page 27)
This lever adjusts the lens direction.
*Front adjustable legs (L /R) (page 27)
+Lens cover
,Remote control signal receptor (page 25)
-Air outlet port
Do not cover this port.WARNINGDo not place your hands or other objects close to the air outlet port.
BHeated air comes out of the air outlet port. Do not place your hands or
face, or objects which cannot withstand heat close to this port [allow at
least 10cm (4”) of space], otherwise burns or damage could result.Projector 

%˛
& $
'
˛ ( #
˛ * ˛ -
˛ ,
˛ +˛
*˛
) 
						

							14-E
NGLISH
ENGLISH
-15
Preparation
Connector panel
#$ % & '
)
(
#SERIAL connector (pages 22, 23, 24 and 66)
This connector is used to connect a personal computer to the projector in
order to control the projector externally. (RS-232C compatible)
$HDMI IN connector (page 23)
This connector is used to input HDMI signals.
%PC IN (RGB input) connector (page 24)
This connector is used to input RGB signals from a PC.
&COMPONENT 1 IN [YP
BPR(C
BCR) input] connectors (page 22)
These connectors are used to input YP
BPRsignals from compatible
equipment such as a DVD player.
'S-VIDEO IN connector (page 22)
This connector is used to input signals from an S-VIDEO-compatible
equipment such as a video deck.
(VIDEO IN connector (page 22)
This connector is used to input video signals from a video equipment such
as a video deck.
)COMPONENT 2 IN [YP
BPR(C
BCR) input] connectors (page 22)
These connectors are used to input YP
BPRsignals from compatible
equipment such as a DVD player. #Connector panel (page 15)
$Air inlet port
Do not cover this port.
%Power input socket (AC IN) (page 26)
The accessory power cord is connected here.
Do not use any power cord other than the accessory power cord.
&Security lock 
This can be used to connect a commercially-available theft-prevention
cable (manufactured by Kensington). This security lock is compatible with
the Microsaver Security System from Kensington.
'Lamp unit cover (page 57)
(MAIN POWER switch (pages 26 and 28)
Projector 




  
						

							ENGLISH
-17
Preparation
16-E
NGLISH
*) (& '#% &$
) (
& *
.
/ -
2 3+
7456
01,'
Projector control panel
Remote control unit
&Arrow (
F F
, G G
, I I
and H H
) buttons (page 42)
These buttons are used to select and adjust items in the on-screen menus.
'ENTER button (page 42)
This button is used to accept and to activate items selected in the on-screen menus.
(MENU button (page 40)
This button is used to display the menu screen. When a menu screen is being
displayed, it can be used to return to a previous screen or to clear the screen.
)INPUT select buttons(page 27)
These buttons are used to switch the input signals from the connected equipment.
*POWER button (pages 26 and 28)
+LIGHT button (page 33)
This button is used to illuminate the buttons on the remote control unit.
,Buttons to operate the selected device
These buttons are used to operate the devices which have been
programed into the remote control unit using the preset or learning
functions of the remote control unit. Refer to “Remote control unit Guide”
for details.
-PROJECTOR button
Buttons from &to (and .are used to operate both the projector and
the other devices which have been programed in the remote control unit.
Be sure to press the PROJECTOR button before operating the projector.
.RETURN button (page 42)
When a menu screen is being displayed, this button is used to return to a
previous screen or to clear the screen.
/SHUTTER button (page 34)
This button is used to momentarily turn off the picture.
0MEM. LOAD (MEMORY LOAD) button (page 34)
This button is used to display the “MEMORY LOAD” menu.
1C.C.M (Cinema Color Management) button (page 36)
This button is used to display the “COLOR MANAGEMENT” menu.
2ADVANCED button (pages 35 and 46)
This button is used to display an item from the “ADVANCED MENU”.
3MAIN button (pages 35 and 44)
This button is used to display an item from the “PICTURE” menu.
4ASPECT button (page 30)
This button is used for aspect adjustment (vertical and horizontal proportions).
5PIC. MODE(PICTURE MODE) button (page 33)
Pressing this button will change the picture mode.
6NORMAL button (page 43)
This button is used to reset the projector adjustment values to the factory
default settings.
7LCD display
The selected device is displayed at the upper side. The setting guide for
the preset and learning functions and the button operation guide for the
selected device are displayed at the lower side. #Power indicator (pages 26, 28 and 29)
This indicator illuminates red when the main power is switched on (standby
mode), and it illuminates green when a picture starts to be projected.
$LAMP indicator (page 55)
This indicator illuminates when it is time to replace the lamp unit. It flashes
if a circuit abnormality is detected.
%TEMP indicator (page 54)
This indicator illuminates if an abnormally high temperature is detected
inside the projector. If the temperature rises above a certain level, the
power supply will be turned off automatically and the indicator will flash. 
						

							L
L
SHSW
82.9 mm
(3-1/4˝)
ENGLISH
-19
Projection distancesNOTE:
BThe dimensions in the table above are approximate.
BFor details about projected image distances, refer to page 69.NOTE:
BPlace the projector so that it is vertical to the screen.
Getting started
Setting-upProjection methodsIn way of installing projector, any one of the following four projection methods
are used. Select whichever projection method matches the setting-up
method. (The projection method can be set from the “OPTION” menu. Refer
to page 52 for details.)
BFront-desk projection
BRear-ceiling projection
(Using a translucent screen)
Menu items Setting
DESK
FRONT DESK/CEILING
FRONT/REAR
Menu items Setting
CEILING
REAR DESK/CEILING
FRONT/REAR
NOTE:
BYou will need to purchase the separate ceiling bracket (ET-PKE300/
ET-PKE700) when using the ceiling installation method.
BDo not set up the projector vertically or tilted horizontally, otherwise it
may cause damage to the projector.
BIt is recommended that you set up the projector in a place that is tilted
at less than ±30°vertically. Setting up the projector in places that are
tilted at more than ±30°vertically may shorten component life.
18-E
NGLISH
Projector position
L: Projection distance
SH: Image height
SW: Image width
Screen
1.01 m(40˝) 0.50 m(1´7˝) 0.89 m(2´11˝) 1.2 m(3´11˝) 2.4 m(7´10˝)
1.27 m(50˝) 0.62 m(2´) 1.11 m(3´7˝) 1.5 m(4´11˝) 3.0 m(9´10˝)
1.52 m(60˝) 0.75 m(2´5˝) 1.33 m(4´4˝) 1.8 m(5´10˝) 3.7 m(12´1˝)
1.77 m(70˝) 0.87 m(2´10˝) 1.55 m(5´1˝) 2.1 m(6´10˝) 4.3 m(14´1˝)
2.03 m(80˝) 1.00 m(3´3˝) 1.77 m(5´9˝) 2.4 m(7´10˝) 4.9 m(16´)
2.28 m(90˝) 1.12 m(3´8˝) 1.99 m(6´6˝) 2.7 m(8´10˝) 5.5 m(18´)
2.54 m(100˝) 1.24 m(4´) 2.21 m(7´3˝) 3.1 m(10´2˝) 6.2 m(20´4˝)
3.05 m(120˝) 1.49 m(4´10˝) 2.66 m(8´8˝) 3.7 m(12´1˝) 7.4 m(24´3˝)
3.81 m(150˝)
5.08 m(200˝)1.87 m(6´1˝)
2.49 m(8´2˝)3.32 m(10´10˝)
4.43 m(14´6˝)4.6 m(15´1˝)
6.2 m(20´4˝)9.3 m(30´6˝)
12.4 m(40´8˝)
Screen size (16:9)
Diagonal
lengthHeight 
(SH)Width 
(SW)Projection distance (L)
Wide 
(LW)Telephoto 
(LT)
Screen
BFront-ceiling projection
Menu items Setting
CEILING
FRONT DESK/CEILING
FRONT/REAR
BRear-desk projection
(Using a translucent screen)
Menu items Setting
DESK
REAR DESK/CEILING
FRONT/REAR