Panasonic Projector Pt Ae2000u Operating Instructions

ENGLISH - 21
Basic Operation
Projecting an image
1. Switch on the connected devices.
 Press the play button of the required device.
2. Press the INPUT button to select the required input 
method if needed. See “Switching the input signal” 
on page 23.
 The image will be projected on the screen.
1. Press the ASPECT button to select the required 
aspect mode. See “Switching the aspect ratio” on 
page 23.
2. Adjust the projected image with the lens shift dials. 
See “Lens shift and positioning” on page 16....

22 - ENGLISH
Basic Operation
Remote control operation
You can operate the projector with the remote control 
within the remote range 7 m (2211).
QFacing to the projector
Ensure the remote control emitter is facing to the 
remote control signal receptor on front/back of the 
projector and press the required buttons to 
operate.
QFacing to the screen
Ensure the remote control emitter is facing to the 
screen and press the required buttons to operate 
the projector. The signal will be reflected off the...

Basic Operation
Remote control operation
ENGLISH - 23
You can switch the input method manually 
by pressing the INPUT button. Press the 
button several times or press I H to cycle 
through the input methods as follows. The 
actual projected image will be changed in a 
while.
 The graphical guidance will be displayed on the upper 
right of the projected image and you can confirm the 
selected input method which is highlighted in yellow. See 
“INPUT GUIDE” on page 40.
The aspect ratio will be selected...

Basic Operation
Remote control operation
24 - ENGLISH
You can display the image brightness and 
contrast level of the input signal with a 
waveform. See “WAVEFORM MONITOR” 
on page 32.
JDisplaying the waveform
1. Press the WAVEFORM button and display the 
waveform monitor.
 Press the WAVEFORM button again to escape from 
the waveform mode.
2. Press ENTER button until the required waveform 
option is displayed.
 In FULL SCAN mode, press F G I H to change 
the waveform position.
 In SINGLE LINE SCAN mode,...

Basic Operation
Remote control operation
ENGLISH - 25
QAdjusting with RGB options
1. Press the ENTER button until the required option 
is displayed.
2. Press the PIC. ADJUST twice to display the 
GAMMA of the ADVANCED MENU menu.
3. Press G several times to display the required 
brightness option.
4. Adjust the brightness option by pressing I H.
 Adjust the bottom line of the waveform to 0% 
(0 IRE or 7.5 IRE).
 Setting range: -16 to +16
5. Press G once to display the required contrast 
option.
6. Adjust...

Basic Operation
Remote control operation
26 - ENGLISH
You can adjust a selected color individually 
and save and retrieve under the PICTURE 
MODE setting. Press the COLOR M. button 
to open the menu.
JCreate a new profile
QAdjusting the selected color
Select a color and adjust COLOR, TINT and 
BRIGHTNESS.
1. Select the CURSOR menu and press ENTER.
 The projected image is captured, and the target 
cursor is displayed. 
 When the LOG is fully stored, the target cursor will 
not be displayed. See “Managing...

Basic Operation
Remote control operation
ENGLISH - 27
QSaving a log setting as a profile
Return to the COLOR MANAGEMENT menu and 
save the stored log as a profile. Make sure that the 
PICTURE MODE is not switched.
1. Select the PROFILE SAVE menu and press 
ENTER
 The PROFILE SAVE menu is displayed. You can 
save the profile as USER1, USER2 and USER3.
2. Press ENTER to save the profile
 The confirmation screen is displayed. Press ENTER 
again to save.
3. Use F G I H to specify the location of the...

28 - ENGLISH
Settings
Menu Navigation
The menu system allows you to access functions which do not have their own dedicated buttons on the remote 
control. The menu options are structured and categorized. You can navigate through the menu with F G H I 
buttons.
Main menu and sub-menu
NOTE:
• Some default settings vary by the selected input signal.
• Sub-menu items vary according to the selected input signal.
• Some settings are adjustable without any signals.
Main menuSub-menuOptions (Underlined is...

Menu Navigation
ENGLISH - 29
Settings
Main menuSub-menuOptions (Underlined is default setting)Page
POSITION H-POSITION
• Default: 0page 36
V-POSITION
• Default: 0page 36
DOT CLOCK
*1
*1.COMPUTER signals only
• Default: 0page 36
CLOCK PHASE
*2
*2.COMPUTER/COMPONENT signals only
• Default: 0page 36
ASPECT 4:3 16:9 14:9page 36
ZOOM1 ZOOM2 JUST
WSS
*3
*3.VIDEO/S-VIDEO/COMPONENT signals only
page 38
OVER SCAN
*4
*4. Not available with COMPUTER signals
• Default: 0page 38
KEYSTONE
• Default: 0page 38
AUTO...

Settings
Menu Navigation
30 - ENGLISH
JDisplaying the main menu
Press the MENU button to display the main 
menu and the operating guidance.
JAdjusting with the bar scale 
items
The triangle mark under the bar indicates factory 
default setting and the square indicates the current 
setting.
JReturning to the previous menu
Press the MENU or RETURN button to return to 
the previous menu. Press repeatedly to escape 
from the menu mode and return to the projection.
JOperating procedure
1. Press F G to scroll...