Panasonic Projection Television Pt 52dl52 Operating Instructions

11
Audio
OUTPBY PRDVD(Y- PB-PR) OUT
L R
AUDIOL
R
VIDEO
2 1COMPONENT
VIDEO INPUT
PR
PB
Y
How to connect the COMPONENT VIDEO Input Terminals
(DVD Player)
Note:
Similar connections are available at the COMPONENT VIDEO Input 1, 2 Terminals.
Installation
How to connect the DIGITAL IN Terminals
When connecting a DTV decoder to DIGITAL-IN, be sure not to select “SKIP” or “PC” from the INPUT LABEL menu. Failing
to do so may result in a distorted display or black out (refer to page 36).
1. Connecting a DTV...

12
Installation
AUDIO VIDEO S VIDEO
L
R
2 13INPUT PROG
OUT
AUDIOL
R
DIGITAL IN
DIGITAL IN cable
(Supplied)
K1HA24DA0005 (2 m) PC with digital
RGB video out
Audio Connect a cable that matches
the audio output terminal on the
computer.
2 × RCA plug
Note:
If your PC does not support the Plug-and-Play capability (DDC1/2B) for displays, it will require reconfiguration after the
display is connected to the PC.
Pin No.Signal Name
T.M.D.S. data 2-
T.M.D.S. data 2+
T.M.D.S. data 2 shielded
DDC clock
DDC data...

13
Conversion adapter (if necessary)
AudioRGBD-SUB 15P
2 × RCA plug PC cable
(supplied)
K1HA30DA0003 (2 m)
Connect a cable that matches
the audio output terminal on the computer.
PC INPUTINPUT 4
VIDEO
L-AUDIO-R
COMPUTER
Installation
How to connect the PC Input Terminals
Signal Names for D-SUB 15P Connector
Pin Layout for PC Input
Terminal
Pin No.
1
2
3
4
5
Pin No.
6
7
8
9
10
Pin No.
11
12
13
14
15
Signal Name
R
G
B
GND (Ground)
GND (Ground)
Signal Name
GND (Ground)
GND (Ground)
GND (Ground)
NC (not...

14
Illuminated Remote Control
Location of Controls
Power button
Press to turn the TV ON or OFF (See page 18, 19).
Note: The TV’s power cord must first be plugged into the wall outlet
and then turned on at the POWER switch (standby mode).
R-TUNE button
Switches to previously viewed channel or video mode. MUTE button
Press this button to mute the sound, press again to cancel the mute.
Operation of other Device
TV
DTVCBL
AUXDVD
VCR
DBS
RCVR
Mode Selection buttons
Selects the operation mode for the remote...

15
ACTION
123
456
78
09
TV
DTVCBL
AUXDVD
VCR
DBS
RCVR
POWER
CH
CH VOL VOL
PLAY R-TUNE PROGGUIDE RECALLSAP
PAGE EXIT
PIP SPLIT MOVE SWAPSTOP PAUSERECPIP MAXFFPIP MINREW
BBE
MENU
FREEZE
TV/VCRPIP CH
VCR CHSEARCHOPEN/CLOSE
MUTEASPECTTV/VIDEOLIGHT
ACTIONCH
CH VOL VOL
RECALLBBE
MENU
GUIDE PAGE EXIT
Direct program number
selection buttons Lights the remote control buttons.
Press to illuminate remote buttons.
Returns to normal viewing from the MENU screen.
Previous item in MENU. TV/VIDEO button
The input mode...

16
AUDIO VIDEO S-VIDEO
L
R2 13INPUT PROG
OUTAUDIOL
R
DIGITAL INAUDIOL
RVIDEO
2 1COMPONENT
VIDEO INPUTPRPBY
ANT1 ANT2SPLIT
OUTAUDIO VIDEO S VIDEO
L
R
2 13INPUT PROG
OUT
AUDIOL
R
DIGITAL IN
AUDIOL
R
VIDEO
2 1COMPONENT
VIDEO INPUT
PR
PB
Y
DLPTMA TEXAS INSTRUMENTS TECHNOLOGYHDTVCOMPATIBLE   1080 i / 720p
PC INPUT
VOLUMETV/VIDEO ACTIONCHANNEL
LAMP TEMPG-POWER ON
POWER
S-VIDEO
VIDEOL-AUDIO-R
INPUT 4
Input1 terminals
 (see page 10)
Input2 terminals (see page 10) Component signal input
(see page 11)
Location of...

17
Cable TV / VHF, UHF and CATV
INPUT
OUTPUTDLPTMA TEXAS INSTRUMENTS TECHNOLOGYHDTVCOMPATIBLE   1080 i / 720p
VOLUMETV/VIDEO ACTIONCHANNELLAMP TEMPG-POWER ON
POWER
ANTENNA TERMINAL ON THE
BACK OF THE PROJECTION TV
CABLE BOX To Antenna
Input
Incoming Cable from
Antenna or Cable TV
System.
Power switch
Remote control sensorOperation can be done
from the TV set.
• Volume adjusters
• Channel selectors
DTV
AUXDVD
VCR
DBS
RCVR
SAP
MUTEASPECTTV/VIDEOLIGHT
POWER
CH
VOL VOL
ACTION
TV
CBL
When the antenna cable is...

18
Push the Power switch on the projection TV to turn the power
on.
Push the Power switch on the projection TV to turn the set off.
Example: The screen above is displayed for a while after the
projection TV is turned on. (Setting condition is an
example.)
Power ON / OFF
Connecting the Plug to the Wall Outlet
Turning the Power ON and OFF
DLPTMA TEXAS INSTRUMENTS TECHNOLOGYHDTVCOMPATIBLE   1080 i / 720p
DLPTMA TEXAS INSTRUMENTS TECHNOLOGYHDTVCOMPATIBLE   1080 i / 720p
LAMP TEMPG-POWER ON
POWER
Always be...

19
Power ON / OFF
ACTION
TV
DTVCBL
AUXDVD
VCR
DBS
RCVR
CH
CH VOL VOL
RECALLSAPBBE
MENU
MUTEASPECTTV/VIDEOLIGHT
POWER
POWER
Power (ON/Off) button
Push the Power button to turn the projection TV ON,
from Stand-by mode.
The Power Indicator will blink Green.
Approximately 10 seconds
The Power Indicator will become Green.
Push the Power button to turn the projection TV to
Stand-by mode.
The Power Indicator will become Orange.
Approximately 10 seconds
The Power Indicator will blink Orange.
Approximately 90...

20
MODE
PROG  CHAN
OTHER  ADJ. IDIOMA /
LANGUE
CC
SET UPENGLISH
Roller Guide Menu Navigation
1
ACTIONCH
CH VOL VOL
2
ACTIONCH
CH VOL VOL3
ACTIONCH
CH VOL VOL
4
ACTIONCH
CH VOL VOL
5
ACTIONCH
CH VOL VOL
Press to display the roller guide menu.
Press to rotate to desired icon.
Press to display the main menu and
submenu field.
Press to select main menu feature.
Press to enter submenu field.
Press to select desired submenu feature.
Press to select or adjust.
Press twice to return to the roller guide.
EXITSET...