Panasonic Projection Television Pt 52dl52 Operating Instructions

							11
Audio
OUTPBY PRDVD(Y- PB-PR) OUT
L R
AUDIOL
R
VIDEO
2 1COMPONENT
VIDEO INPUT
PR
PB
Y
How to connect the COMPONENT VIDEO Input Terminals
(DVD Player)
Note:
Similar connections are available at the COMPONENT VIDEO Input 1, 2 Terminals.
Installation
How to connect the DIGITAL IN Terminals
When connecting a DTV decoder to DIGITAL-IN, be sure not to select “SKIP” or “PC” from the INPUT LABEL menu. Failing
to do so may result in a distorted display or black out (refer to page 36).
1. Connecting a DTV Decoder to DIGITAL IN
AUDIO VIDEO S VIDEO
L
R
2 13INPUT PROG
OUT
AUDIOL
R
DIGITAL IN
DIGITAL IN cable
(Supplied)
K1HA24DA0005 (2 m) DTV Decoder
AudioDIGITAL IN terminals
2 × RCA plug
By inputting a High-bandwidth Digital Content Protection high-definition picture source to the DIGITAL IN terminal of this
television, high-definition pictures can be displayed on the screen in their digital form. (This terminal is for use in the future
when High-bandwidth Digital Content Protection DTV decoders, DVD players and D-VHS are put on the market.)
Note:
The DIGITAL IN terminal can only be used with 1080i, 720p and 480p picture signals. Set the DTV Decode DIGITAL OUT
terminal Output setting to 1080i, 720p or 480p. For detailed information, refer to the DTV decoder instruction manual. If
you cannot display the picture because your DTV decoder does not have a DIGITAL OUT terminal Output setting, use the
component Video Input (or the S Video Input or Video Input). In this case the picture will be displayed as an analog signal. 
						

							12
Installation
AUDIO VIDEO S VIDEO
L
R
2 13INPUT PROG
OUT
AUDIOL
R
DIGITAL IN
DIGITAL IN cable
(Supplied)
K1HA24DA0005 (2 m) PC with digital
RGB video out
Audio Connect a cable that matches
the audio output terminal on the
computer.
2 × RCA plug
Note:
If your PC does not support the Plug-and-Play capability (DDC1/2B) for displays, it will require reconfiguration after the
display is connected to the PC.
Pin No.Signal Name
T.M.D.S. data 2-
T.M.D.S. data 2+
T.M.D.S. data 2 shielded
DDC clock
DDC data
T.M.D.S. data 1-
T.M.D.S. data 1+
T.M.D.S. data 1 shieldedSignal Name
+5 V DC
Ground
Hot plug sense
T.M.D.S. data 0-
T.M.D.S. data 0+
T.M.D.S. data 0 shielded
T.M.D.S. clock shield
T.M.D.S. clock+
T.M.D.S. clock-Pin No.
Connection port view Digital RGB Input Connector
Pin LayoutsDIGITAL IN terminals When connecting a PC to DIGITAL-IN, be sure to select “PC” from the INPUT LABEL menu. Failing to do so may result in
a distorted display or black out (refer to page 36).
2. Connecting a PC to DIGITAL IN 
						

							13
Conversion adapter (if necessary)
AudioRGBD-SUB 15P
2 × RCA plug PC cable
(supplied)
K1HA30DA0003 (2 m)
Connect a cable that matches
the audio output terminal on the computer.
PC INPUTINPUT 4
VIDEO
L-AUDIO-R
COMPUTER
Installation
How to connect the PC Input Terminals
Signal Names for D-SUB 15P Connector
Pin Layout for PC Input
Terminal
Pin No.
1
2
3
4
5
Pin No.
6
7
8
9
10
Pin No.
11
12
13
14
15
Signal Name
R
G
B
GND (Ground)
GND (Ground)
Signal Name
GND (Ground)
GND (Ground)
GND (Ground)
NC (not connected)
GND (Ground)
Signal Name
GND (Ground)
SDA
HD / SYNC
VD
SCL
1
6 7 83
94 5
10
15 14 13 12 11
2
Notes:
(1) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will
need to make setting changes to the computer at the time of connection.
(2) Some PC models cannot be connected to the set.
(3) There is no need to use an adapter for computers with PC / AT compatible D-SUB 15P terminal.
(4) The computer shown in the illustration is for example purposes only.
(5) Additional equipment and cables shown are not supplied with this set.
(6) The picture will become dark if a PC signal with a vertical scanning frequency of 62 Hz is input. To obtain the optimum
picture quality with the projection TV, a vertical scanning frequency of 60 Hz is recommended.
(7) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
Digital and analog RGB signals that can be input
The table below lists the different types of digital and analog RGB signals that can be input.
If a signal which differs greatly from any of the types listed below is input, the picture
image may not be displayed correctly, or a black background may displayed.
Note:
The number of dots for this set is 800 × 600 for NORMAL display. Number of dots other than 800 × 600 in the above data,
will be converted to 800 × 600 (with the exception of MAC 16, which will be displayed in 832 × 624 dots). Display mode name No. of dots (H 
× ×× ×
× V)Horizontal scanning Vertical scanning DIGITAL PC INPUT
frequency (kHz) frequency (Hz) IN (Analog)
VGA400 640 × 400 31.5 70.1∗∗
VGA480 640 × 480 31.5 59.9∗∗
SVGA 800 × 600 37.9 60.3∗∗
XGA 1024 × 768 48.4 60.0∗∗
MAC16 832 × 624 49.7 74.6∗
720p 1280 × 720 45.0 60.0∗
∗ Mark:
Input signal can be displayed. 
						

							14
Illuminated Remote Control
Location of Controls
Power button
Press to turn the TV ON or OFF (See page 18, 19).
Note: The TV’s power cord must first be plugged into the wall outlet
and then turned on at the POWER switch (standby mode).
R-TUNE button
Switches to previously viewed channel or video mode. MUTE button
Press this button to mute the sound, press again to cancel the mute.
Operation of other Device
TV
DTVCBL
AUXDVD
VCR
DBS
RCVR
Mode Selection buttons
Selects the operation mode for the remote control. (See page 58)
VCR Mode Selection for Remote Control
Digital Video Disk Mode Selection for Remote ControlAux Mode Selection for Remote Control
TV Mode Selection for Remote ControlDigital Broadcasting Satellite for
Remote Control Receiver/Amplifier Mode Selection
for Remote Control
Digital TV Mode Selection for Remote Control
Cable TV Mode Selection for Remote Control
PIP or SPLIT FREZE
TV/VCR Switch
TV/DBS Switch
-
-
PIP or SPLIT CH up/down
VCR CH up/down
TV/DBS CH up/down
-
-
PIP Search
-
-
OPEN/CLOSE
-
TV
VCR
CABLE/DBS
DVD/LD/CD
RCVR
TV
VCR
CABLE/DBS
DVD/LD/CD
RCVRPIP Minimize/Maximize
VCR REW/FF
-
Skip Search REW/FF
Surround 
-/+
-
PLAY
-
PLAY
-
-
VCR RECORD
DBS RECORD
-
--
Pause
-
Pause
--
STOP
-
STOP
-
Buttons Buttons
DevicePIP MAXFFSTOPPIP MINREWPLAYPAUSE
Buttons Buttons
DeviceSEARCHOPEN/CLOSERECFREEZETV/VCRPIP CH
VCR CH
ASPECT button
Change of screen size (See page 44).
R-TUNE
ZOOM1ZOOM2 FULL JUST
4 : 3 
						

							15
ACTION
123
456
78
09
TV
DTVCBL
AUXDVD
VCR
DBS
RCVR
POWER
CH
CH VOL VOL
PLAY R-TUNE PROGGUIDE RECALLSAP
PAGE EXIT
PIP SPLIT MOVE SWAPSTOP PAUSERECPIP MAXFFPIP MINREW
BBE
MENU
FREEZE
TV/VCRPIP CH
VCR CHSEARCHOPEN/CLOSE
MUTEASPECTTV/VIDEOLIGHT
ACTIONCH
CH VOL VOL
RECALLBBE
MENU
GUIDE PAGE EXIT
Direct program number
selection buttons Lights the remote control buttons.
Press to illuminate remote buttons.
Returns to normal viewing from the MENU screen.
Previous item in MENU. TV/VIDEO button
The input mode changes each time this button is pressed.
[Example]
GUIDE button
for DBS.
Location of Controls
SAP button
Selects Audio mode (See page 37).
Page up/down for DBS,
skip +/- for DVD & CD.
Swap pictures in Split Screen and Picture in Picture operation
(See page 40, 43).PROG dash button
Program dash channel numbers for DTV and DBS.
PROG
Move PIP frame in Picture in Picture Operation (See page 41).
Split Screen (see page 42)
Picture in Picture Operation (see page 40)
COMPONENT 2 TV
COMPONENT 1
VIDEO 3 VIDEO 4 DIGITAL-IN PCVIDEO 1
VIDEO 2
Reduces volume
Moves cursor to the
left during menu
mode.
Displays menu
Press to access
DTV, DBS or DVD
menus.
During TV mode press
to select BBE ON or
BBE OFF.Changes to the next channel down
Moves cursor downward during menu mode.Increases volume
Moves cursor to
the right during
menu mode. Changes to the next channel up
Moves cursor upward during menu mode.
Press to display
time, channel,
sleep timer and
other options.
STEREO SAP MONO 
						

							16
AUDIO VIDEO S-VIDEO
L
R2 13INPUT PROG
OUTAUDIOL
R
DIGITAL INAUDIOL
RVIDEO
2 1COMPONENT
VIDEO INPUTPRPBY
ANT1 ANT2SPLIT
OUTAUDIO VIDEO S VIDEO
L
R
2 13INPUT PROG
OUT
AUDIOL
R
DIGITAL IN
AUDIOL
R
VIDEO
2 1COMPONENT
VIDEO INPUT
PR
PB
Y
DLPTMA TEXAS INSTRUMENTS TECHNOLOGYHDTVCOMPATIBLE   1080 i / 720p
PC INPUT
VOLUMETV/VIDEO ACTIONCHANNEL
LAMP TEMPG-POWER ON
POWER
S-VIDEO
VIDEOL-AUDIO-R
INPUT 4
Input1 terminals
 (see page 10)
Input2 terminals (see page 10) Component signal input
(see page 11)
Location of Controls
Controls and Terminals on the Projection TV
Input mode selection buttons (see page 15)Volume up(+) / down(–) buttons (see page 15, 17)
Channel up / down
buttons
(see page 15, 17) Action button (Press to
make selections.)
Input4 terminals
Video camera and TV game
cable terminal Open
Open
PC Input terminal Press the 
 
mark on the center of the
front cover to open.
  FRONT
Lamp unit
(see page 7)
Speaker panelRemote Control Sensor (see page 18, 19) TEMP
This indicator lights up when there is an abnormal
temperature in the unit (see page 65) LAMP
This indicator lights up when there is a malfunction with the
lamp unit (see page 7, 65) POWER INDICATOR
G-POWER ON
 (see page 18, 19)
POWER SWITCH
 (see page 18)
Prog out terminals
(see page 10)
  REARDIGITAL IN Terminals (see page 11, 12)
Input3 terminals (see page 10) 
						

							17
Cable TV / VHF, UHF and CATV
INPUT
OUTPUTDLPTMA TEXAS INSTRUMENTS TECHNOLOGYHDTVCOMPATIBLE   1080 i / 720p
VOLUMETV/VIDEO ACTIONCHANNELLAMP TEMPG-POWER ON
POWER
ANTENNA TERMINAL ON THE
BACK OF THE PROJECTION TV
CABLE BOX To Antenna
Input
Incoming Cable from
Antenna or Cable TV
System.
Power switch
Remote control sensorOperation can be done
from the TV set.
• Volume adjusters
• Channel selectors
DTV
AUXDVD
VCR
DBS
RCVR
SAP
MUTEASPECTTV/VIDEOLIGHT
POWER
CH
VOL VOL
ACTION
TV
CBL
When the antenna cable is connected to the TV antenna
terminal via a cable box or VCR, set the TV channel to CH3
or CH4.
This does not apply when signal is input from VIDEO
INPUT.
VHF, UHF and CATV Cable TV
Confirming
Confirm that registration with cable TV provider and
connection of equipment are completed. Turn the CABLE
BOX on and select the desired volume level.
Press while pointing the remote control
towards the CABLE BOX.
Note:
The remote control code number is set for
Panasonic products.
When peripheral equipment does not
operate, reset code (See page 58 - 59).
Operate the CABLE BOX and select the desired
volume level.
POWER
CBL1
2
3Press  CBL  to confirm.Press to turn the TV on (See page 18,
19). Press 
TV to operate the TV set with
the remote control.
Press to select the desired
channel.
Select the desired volume level.
Notes:
(1) The channel number and volume level remain the same
even after the TV is turned off.
(2) Power consumption and howls can be reduced if the
volume level is lowered.1
2
3
4
POWER
TV
ACTIONCH
CH VOL VOL
ACTIONCH
CH VOL VOL 
						

							18
Push the Power switch on the projection TV to turn the power
on.
Push the Power switch on the projection TV to turn the set off.
Example: The screen above is displayed for a while after the
projection TV is turned on. (Setting condition is an
example.)
Power ON / OFF
Connecting the Plug to the Wall Outlet
Turning the Power ON and OFF
DLPTMA TEXAS INSTRUMENTS TECHNOLOGYHDTVCOMPATIBLE   1080 i / 720p
DLPTMA TEXAS INSTRUMENTS TECHNOLOGYHDTVCOMPATIBLE   1080 i / 720p
LAMP TEMPG-POWER ON
POWER
Always be sure to follow the procedure given below to turn the projection TV power ON and OFF.
• The lamp cooling fan will continue to operate for approximately 90 seconds after the power is turned off by the remote control.
After the cooling fan has stopped, the power indicator will not illuminate (Stand-by).
If you wish to turn the power ON while the cooling fan is operating, press the power button on the remote controller. The
power indicator on the TV will then flash in green, and the projection TV will turn ON as soon as the cooling fan stops.
In normal circumstances, use the remote control to turn the power OFF (turning the picture OFF).
Do not disconnect the power cord from the power outlet and do not open any circuit breakers while the cooling
fan is still operating.The projection TV must first be switched on at the wall
outlet.
The projection TV will become standby mode.
CH 3
SAPJUST
VIVID
Power switch
Remote control sensor 
						

							19
Power ON / OFF
ACTION
TV
DTVCBL
AUXDVD
VCR
DBS
RCVR
CH
CH VOL VOL
RECALLSAPBBE
MENU
MUTEASPECTTV/VIDEOLIGHT
POWER
POWER
Power (ON/Off) button
Push the Power button to turn the projection TV ON,
from Stand-by mode.
The Power Indicator will blink Green.
Approximately 10 seconds
The Power Indicator will become Green.
Push the Power button to turn the projection TV to
Stand-by mode.
The Power Indicator will become Orange.
Approximately 10 seconds
The Power Indicator will blink Orange.
Approximately 90 seconds.
The power Indicator light will go out.
Note:
The TV will still consume some power as long as the
power cord is still inserted into the wall outlet.
Menu Language Selection
In SET UP Menu, Select IDIOMA/LANGUE to change menu language to ENGLISH, ESPAÑOL (Spanish) or FRANÇAIS
(French). (refer to page 22)
LED
Not illuminated
Green
Green blink
Orange
Orange blink
ACTION
Stand – by
Power – ON
Power – ON
(approximately 10 seconds after)
Power – OFF (Blanking mode)
(approximately 10 seconds after)
Power – OFF (Cooling mode)
(approximately 90 seconds after)
The Power Indicator
ENGLISH 
						

							20
MODE
PROG  CHAN
OTHER  ADJ. IDIOMA /
LANGUE
CC
SET UPENGLISH
Roller Guide Menu Navigation
1
ACTIONCH
CH VOL VOL
2
ACTIONCH
CH VOL VOL3
ACTIONCH
CH VOL VOL
4
ACTIONCH
CH VOL VOL
5
ACTIONCH
CH VOL VOL
Press to display the roller guide menu.
Press to rotate to desired icon.
Press to display the main menu and
submenu field.
Press to select main menu feature.
Press to enter submenu field.
Press to select desired submenu feature.
Press to select or adjust.
Press twice to return to the roller guide.
EXITSET UP
ON  MUTE
MODEPROG  CHAN
OTHER  ADJ. IDIOMA /
LANGUE
CCCCCC
SET UP
OFFNO
ON  MUTE
MODEPROG  CHAN
OTHER  ADJ. IDIOMA /
LANGUE
CCCC
CC
SET UP
C1 NO
MODE
PROG  CHAN
OTHER  ADJ. IDIOMA /
LANGUE
CCCCCC
SET UP
OFF ON  MUTENO
ON  MUTE
MODEPROG  CHAN
OTHER  ADJ. IDIOMA /
LANGUE
CCCCCC
SET UP
OFFNO
Submenu field Main menu field
EXITSET UP
NORMAL PICTURE
Press to exit roller guide.
This returns the set to the normal viewing.