Panasonic Progressive Wide Plasma Display Th 42pwd5 Operating Instructions

11
PR/CR/RPB/CB/B Y/G
COMPONENT/RGB INAV
VDHDRLS VIDEO
INVIDEO
INAUDIO
INRLAUDIOAUDIOVIDEO
OUT
1
PC    IN SERIAL
2
Connections
SPEAKER
Terminals (R)
– Cable fixing bands
Secure any excess cables with bands, as required.
SPEAKER
Terminals (L)
Pass the attached cable fixing
band through the clip as
shown in the figure.
AV Terminals
(see page 12, 13)To tighten:
PullTo tighten:
Pull Push
the catch To secure cables connected to Terminals, wrap
the cable fixing band around them then pass the
pointed end...

12
1
2
1
2
Connections
Speakers connection
When connecting the speakers, be sure to use only the optional accessory
speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
AV Input Terminals connection
Connect the signal source equipment.
An S VIDEO VCR connection
Speakers (Optional accessories)
Luminance earth
Luminance inChrominance earth
Chrominance in
S VIDEO 4 pin socket
(S VIDEO VCR)
S VIDEO
Video input to
S VIDEO
socket Audio input to
L/R socketsAUDIO 2×RCA audio...

13
Connections
VIDEO signal connection
S VIDEO
INVIDEO
OUT
Audio
OUTVideo
OUT
RL
VIDEO
RCA-BNC video cableVideo input to
BNC socket
Audio input to
L/R sockets AUDIO
2×RCA audio cables
VIDEO
RCA video cable
Audio
OUTVideo
OUT
RL
Video input to
BNC socket
RCA-BNC adapter plug
Audio input to L/R sockets AUDIO
2×RCA audio cables
(VCR)
(VCR)
AV
RLAUDIO
INVIDEO
IN
S VIDEO
IN
AV
RLAUDIO
INVIDEO
IN
BNC cable
VIDEO
OUT
VIDEO OUT
MONITOR DEVICE
(Example) color CRT monitor Notes:
(1) S-Video input will override the...

14
Connections
COMPONENT/RGB Input connection
Notes:
(1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “COMPONENT”. (see page 36)
(2) Additional equipment, cables and adaptor plugs shown are not supplied with this set.
Component signals (Y, PB, PR) connection
Notes:
(1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “RGB”. (see page 36)
(2) Additional equipment, cables and adaptor plugs shown are not supplied with this set.
RGB signal (R, G, B, HD, VD) connection
Audio...

15
Connections
PC Input Terminals connection
Notes:
(1) Computer signals which can be input are those with a horizontal scanning frequency of 15.6 to 110 kHz and vertical
scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200
lines.)
(2) The display resolution is a maximum of 640 × 480 dots when the aspect mode is set to “NORMAL”, and 852 × 480 dots
when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may...

16
Connections
1 678
39
45
1015 14 13 12 11
2
Signal Names for D-sub 15P Connector
Pin layout for PC input
terminal
Pin No.
1
2
3
4
5
Pin No.
6
7
8
9
10
Pin No.
11
12
13
14
15
Signal Name
R
G
B
GND (Ground)
GND (Ground)
Signal Name
GND (Ground)
GND (Ground)
GND (Ground)
NC (not connected)
GND (Ground)
Signal Name
GND (Ground)
SDA
HD/SYNC
VD
SCL
∗ ∗∗ ∗
∗ Mark:
By installing the RGB(digital)Terminal
Board(TY-42TM4D) to this set the PC
input signal can be displayed. VIDEO/COMPONENT/RGB/PC/DVI input signals...

17
Connections
SERIAL Terminals connection
Notes:
(1) Use the RS-232C cable to connect the computer to the Plasma Display.
(2) The computer shown is for example purposes only.
(3) Additional equipment and cables shown are not supplied with this set.
SERIALRS-232C 
straight cable
D-sub 9p
COMPUTER
Less than
3 15/16
(10 cm)
Ferrite core 
(large size)
(supplied)
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
The SERIAL terminal conforms to the RS-232C interface...

18
INPUT
SURROUND
VOL
NR
SELECT
OSD  LANGUAGE
SET
English (
UK)
Deutsch
Fran  ais
Italiano
Es
pa  ol
ENGLISH (
US)
R - STANDBY
G   POWER ONINPUT—   VOL      +
R - STANDBY
G   POWER ONTY-42PWD5
VIDEONORMAL
Power ON/OFF
Press the  
button on the remote control to turn the
Plasma Display off.
Power Indicator: Red (STAND-BY)
Press the 
 
button on the remote control to turn the
Plasma Display on.
Power Indicator: Green
To turn the power for the Plasma Display off, press the 
 
switch
on the Plasma Display,...

19
Selecting the On-Screen Menu Language
Select the Input Signal
R - STANDBY
G   POWER ONINPUT—   VOL      +
—  VOL      +INPUT
Press the INPUT button to select the input
video signal desired from equipment such as
a VCR which has been connected to the
Plasma Display.
SURROUND
VOL
NR
INPUT
INPUT
Power ON/OFF and Input Signal Selection
Input signals will change as follows:
For COMPONENT INPUT (see page 36)
For RGB INPUT (see page 36)
VIDEO          COMPONENT          PC
VIDEO          RGB          PC
SET...

20
PLASMA DISPLAY
INPUT
SURROUND
VOL
NR
PICTURE
SOUNDSET UP
ASPECT PICTURE
POS. /SIZE
OFF TIMER
PC
SET  UP
SIGNAL
SCREENSAVER
COMPONENT/RGB-IN  SELECT
RGB
OSD  LANGUAGEENGLISH (
US)
MULTI DISPLAY SETUPSET UP TIMER
On-Screen Menu Display from Remote Control
To PICTURE adjust menu
 (see page 28)
To ADVANCED  SETTINGS
(see page 28, 29)
To PICTURE POS./SIZE adjust
menu (see page 24)
During “VIDEO (S VIDEO)” and
“COMPONENT” input signal modes.Press to select each item.
PICTURE
NORMALIZE
PICTURE  MENU...