Panasonic Progressive Plasma Television Th 37pa20 Operating Instructions

11
PROG OUTCOMPONENT VIDEO INPUT
S VIDEO
DIGITAL
IN
VIDEOY
P
B
L
RL
R P
R
1212INPUT
VIDEO
TO AUDIO
AMPAUDIO
ANT 1 ANT 2SPLIT
OUT
Notes:
(1) To obtain optimum quality picture and sound, an Aerial, the correct cable (75 Ohm coaxial) and the correct terminating
plug are required.
(2) If a communal Aerial system is used, you may require the correct connection cable and plug between the wall Aerial
socket and your television receiver.
(3) Your local Television Service Centre or Dealer may be able to assist...

12
Follow this diagram when connecting your television to a cable box only.
Optional Equipment Connections
Note: The remote control must be programmed with supplied codes to operate the cable box (see page 58).
Procedure
1. Select ANT2 in the SET UP menu.
2. Tune the television to Channel 3 or Channel 4.
3. Using the cable box, tune to the premium cable channel you would like to view.
Note:
To use special features such as Favorite Channels and Channel Captions, ANT1 must be selected in the SET UP menu...

13
Cable Connection
Follow this diagram when connecting your television to a VCR only.
Note: The remote control must be programmed with supplied codes to operate the VCR (see page 56, 57).
 VCR Connection
Procedure
1. Select ANT1 in the SET UP menu.  (See page 24)
2. Tune the television to the television program you would like to  view. Viewing a television program
Procedure
 • Option A
1. 
Press the TV/VIDEO button on the remote control to select the video input (VIDEO 1, VIDEO 2, etc.) connected to...

14
Cable Connection
Follow this diagram when connecting your television to both a VCR and a cable box.
Notes:
(1) Similar connections are available at the INPUT 1, 2, 3 input terminals.
     Input 3 is located on the front of the unit.
     Select the desired VIDEO input position by pressing the TV/VIDEO button. (See page 21)
(2) When connecting video cables, priority is given to the S-Video cable when the S-Video input terminal and the video
input terminal are connected at the same time. Note: To use...

15
PROG OUTCOMPONENT VIDEO INPUT
S VIDEO
DIGITAL
IN
VIDEOY
P
B
L
RL
R
ANT 1 ANT 2
PR
1212INPUT
VIDEO
TO AUDIO
AMPAUDIOSPLIT
OUT
AUDIO INTPUT
RL
Cable Connection
 Digital TV - Set-Top Box (DTV-STB) or DVD Connection
This television is capable of displaying 1080i and 480p DTV signals when connected to a DTV Tuner set-top-box (STB). In
order to view DTV programming, the STB must be connected to the component video inputs (Y, P
B , PR ) of the television.
A DTV signal must be available in your area. Select...

16
PROG OUTCOMPONENT VIDEO INPUT
S VIDEO
DIGITAL
IN
VIDEOY
P
B
L
RL
R
ANT 1 ANT 2
PR
1212INPUT
VIDEO
TO AUDIO
AMPAUDIOSPLIT
OUT
VIDEO
AUDIO
RL
Cable Connection
Program Out Connection (PROG OUT)
To use the television audio and video with optional equipment, connect the PROG OUT and TO AUDIO AMP connections
on the back of the television.
See optional equipment manual for further instructions for recording and monitoring.CONNECTIONS ON BACK OF TV
Procedure
1. Connect optional equipment to PROG OUT and TO...

17
PC Input Terminals connection
Notes:
(1) Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical
scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
(2) The display resolution is a maximum of 640 × 480 dots when the aspect mode is set to “4:3”, and 852 × 480 dots
when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible...

18
Power ON / OFF
AC cord connection
Connecting the Plug to the Wall Outlet
Note:
The TV’s power cord must first be plugged into the wall
outlet and then turned on at the POWER switch (standby
mode).
Press the POWER switch on the TV to turn the set on.
POWER-ON: Red
When the set is on press the POWER switch on the TV
to turn the set off.
STANDBY: No light
Example: The screen below is displayed for a while after
the TV is turned on. (setting condition is an
example.)
Press the POWER button on the remote...

19
INPUT
OUTPUTS-VIDEOPC CHANNEL VOLUME ACTION INPUTHPJVIDEOVIDEO3R   AUDIO   L
POWERS VIDEOPC CHANNEL VOLUME ACTION INPUTHPJVIDEO
INPUT3
L   AUDIO   R
Cable TV / VHF, UHF and CATV
Press to turn the TV on (See page 18). Press 
TV to operate the TV set with the
remote control.
Press to select the desired channel.
Select the desired volume level.
Notes:
(1) The channel number and volume level remain the same
even after the TV is turned off.
(2) Power consumption and howling sound can be reduced if
the...

20
Illuminated Remote Control
Location of Controls
Power button
Press to turn the TV ON or OFF (See page 18).
Note: The TV’s power cord must first be plugged into the wall outlet
and then turned on at the POWER switch (standby mode).
R-TUNE button
Switches to previously viewed channel or video mode. MUTE button
Press this button to mute the sound, press again to cancel the mute.
Operation of other Device
TV
DTVCBL
AUXDV D
VCR
DBS
RCVR
Mode Selection buttons
Selects the operation mode for the remote...