Panasonic Order Taker Wx T3020 Operating Instructions

11
Control of the device control ter-
minals
The device control terminals of the center module can be
controlled through the Order Taker. 
1. Hold down the C button. A short beep is heard from the speaker of the headset and a connection will be made
toward the device control terminals of the center mod-
ule. 
2. Release the C button. A short beep is heard twice from the speaker of the headset and the connection will be
disconnected toward the device control terminals of the
center module....

12
Manager Mode
(Only one Headset)
Complete ID Registration to do this setting.
The Order Taker set to the Manager mode has following
functionality.
• The manager can interrupt store personnels TALK or PAGE at any time by monopolizing one channel by prior-
ity.
• The Manager hears audio from POS alone.
1. Hold down the power button for 2 seconds or more to turn off the Order Taker.
2. While holding R and T1 simultaneously, press the power button to turn on the Order Taker. The Order Taker
enters manager...

13
Auto-Talk-Lock setup (for only
one Headset)
For a Order Taker where Auto-Talk-Lock is set up, it has a
function to select [Talk] automatically when the vehicle
detector has become active, and you can talk with the cus-
tomer at the menu board. 
1. Confirm that the dip switch 1 of the headset is ON, the dip switch 2 is set at the objective lane, and the power
of the headset is OFF. 
2. Turn on the Order Taker. The message Hello Headset ** (** is the number of headset) is output from the
speaker of the...

14
Caution:Setup of this product should only be performed by
qualified service personnel or system installers.
 Opening the Switch
Compartment
1. Press the power button for 2 seconds or more to turn off
the Order Taker.
2. Unscrew the screw and open the switch compartment.
3. Set the switches.
4. After finishing the setup, replace the cover.
5. Turn on the Order Taker.
 DIP Switch Setup
An eight-bit DIP switch is provided for system setups. The
initial settings are marked with an asterisk *.
Note: Be...

15
SW#8: This switch selects RF Power.ON: Reduce Power
OFF: Full power
ID Registration
1. Press the ID Registration button of the center module for
2 seconds or more. The system is changed to the ID
Registration mode.
2. While holding down the T1 and T2 buttons simultaneous- ly, hold down the power button to turn on the Order
Taker. The Order Taker enters the ID Registration setting
mode where the indicators and buttons have different
functions than in normal operation. You will hear ID
Registration...

16
Troubleshooting
The headset ID is not registered in the center module of the tar-
get.→ Register ID in the center module of the target.
Symptom
The power indicator blinks
red.
Reference
pages
Cause/solution
15
The battery is almost exhausted.
→ Recharge the battery.
(Refer to the operating instructions of the battery charger.)The power indicator lights red
and a constant beep is heard
in the headphone.
–
Cannot turn on the Order
Taker.The battery is exhausted. The battery is not inserted correctly.
→...

17
Specifications
Operating Frequency:1 920 - 1 930 MHz
Required Power Supply: Rechargeable Li-ion Battery, 3.7 V DC
Control Function:  Power (On/Off)
Volume (Up/Down)
Talk (T1/T2)
Page
Lane Selection (A/B)
External Device Control (C)
DIP Switch Setup (8 bit)
Dimensions: 121 mm (W) x 61 mm (H) x 24 mm (D)
{4-3/4 (W) x 2-13/32 (H) x 15/16 (D)}
Weight (excluding battery): 115 g {0.25 lbs}
Ambient operating temperature: –10 °C to +50 °C {14 °F to 122 °F}
Dimensions and weighs indicated are approximate....

18
Optional Accessories
Battery (Li-ion 3.7 V DC, 1 10 0 mAh)  ............................... WX-B3030
Battery Charger ................................................................ WX-Z3040
Headset ................................................................\
............ WX-H3027
Standard Accessory
Operating Instructions (this manual) ................................ 1 pc. 

19
RSS-213Lutilisation de ce dispositif est autorisée seulement aux deux
conditions suivantes : (1) il ne doit pas produire de brouillage,et
(2) lutilisateur du dispositif doit être prêt à accepter tout brouil-
lage radioélectrique reçu, m ême si ce brouillage est susceptible
de compromettre le fonctionnement du dispositif.
ATTENTION: • Risque dexplosion si la batterie nest pas plac ée correctement.
Remplacer uniquement avec le même type ou un type
équivalent.
• Ces instructions de d épannage sont...

20
Limitation de responsabilité
CETTE PUBLICATION EST FOURNIE COMME TEL SANS GARANTIE DE TOUTE SORTE, \
EXPRÈS OU IMPLICITE, ÉTANT
INCLUSE MAIS NON LIMITÉE AUX GARANTIES IMPLICITES DE LA VALEUR MARCHA\
NDE, ADAPTATION POUR TOUT BUT
PARTICULIER OU NON-INFRACTION DES DROITS DUN TIERS.
Déni de la garantie
EN AUCUN CAS MATSUSHITA ELECTRIC INDUSTRIAL
CO., LTD. NE SERA TENU POUR RESPONSABLE POUR
TOUTE PARTIE OU TOUTE PERSONNE, À LEXCEPTION
DU REMPLACEMENT OU DUNE MAINTENANCE
RAISONNABLE DE CE PRODUIT POUR LES...