Panasonic Network Camera Wv Sw132 Wv Sf135 Installation Guide

11
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE 
AVC PATENT PORTFOLIO LICENSE FOR THE 
PERSONAL USE OF A CONSUMER OR 
OTHER USES IN WHICH IT DOES NOT 
RECEIVE REMUNERATION TO (i) ENCODE 
VIDEO IN COMPLIANCE WITH THE AVC 
STANDARD (“AVC VIDEO”) AND/OR (ii) 
DECODE AVC VIDEO THAT WAS ENCODED 
BY A CONSUMER ENGAGED IN A 
PERSONAL ACTIVITY AND/OR WAS 
OBTAINED FROM A VIDEO PROVIDER 
LICENSED TO PROVIDE AVC VIDEO. NO 
LICENSE IS GRANTED OR SHALL BE 
IMPLIED FOR ANY OTHER USE. ADDITIONAL...

12
Precautions for Installation
Panasonic assumes no responsibility for injuries or property damage resulting from fail-
ures arising out of improper installation or operation inconsistent with this documenta-
tion. 
This camera is designed to be used 
indoors. 
This product is not operable outdoors. 
Do not expose this camera to direct sunlight 
for hours and do not install the product near a 
heater or an air conditioner. Otherwise, it may 
cause deformation, discoloration and malfunc-
tion. Keep this...

13
Screw tightening
	 •	
	The
	 screws 	 and 	 bolts 	 must 	 be 	 tightened 	
with an appr

opriate tightening torque 
according to the material and strength of 
the installation area. 
	 •	 Do
	
not
 	
use
 	
an
 	
impact
 	
driver
 . 	
Use
 	
of
 	
an
 	
impact 

driver  may  damage  the  screws  or 
cause tightening excessively. 
	 •	 When
	
a
 	
scr
 ew 	
is
 	
tightened,
 	
make
 	
the
 	
scr

ew  at  a  right  angle  to  the  surface.  After 
tightening  the  screws  or  bolts,  perform 
visual...

14
Major operating controls
About the initial set button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 min-
utes after releasing the button. The camera will start up and the settings including\
 the network set-
tings	 will	 be	 initialized.	 Do	 not	 turn	off	 the	 power	 of	 the	 camera	 during	 the	 process	 of	 initialization.	
Before	initializing	the...

15
z  Use a slotted head screwdriver to open the screw covers (2 places), and then loosen the 2 screws (M3).
x  Remove the dome cover.
	 •	 Hold	both	sides	of	the	cover,	release	the	hook	and	remove	the	dome	cover.
Removing the dome cover base
Important:
	 •	 Remove	 the	 cover	 film	 from	 the	 dome	 section	 of the dome cover after the installation is com-
plete. Do not touch the dome section by hand 
directly after removing the cover film. 
 
    Cover film
Screw cover 

16
Preparations
You can install the camera on a ceiling or a wall. (☞ Pages 16 and 17)Important:
	 •	 Procure	3	screws	(M4)	to	secure	the	camera	to	a	ceiling	or	a	wall,	according	to	the	material	of	 the installation area. In this case, wood screws and nails should not be used. For mounting a 
camera on a concrete ceiling, use an anchor bolt (for M4) or an AY plug bolt (M4) for securing. 
(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
	 •	 Required	pull-out	capacity	of	a	single	screw/bolt	is	196	N...

17
Method of camera installation
Installing the camera directly on the ceiling or wall
Note:
	 •	
Use the installation template label (accessory) with the side with the\
 arrow facing you.
	 •	Ceiling installation:
  Place the installation template label so that the "h" is pointing to the front of the camera (the lens side).
	 •	Wall installation:
  Place the installation template label so that the "h" is pointing down.
 

Place the installation template label (accessory) on the ceiling...

18
Connection
Before starting the connection, turn off the power of the devices to be connected. 
Check and prepare the required devices and cables for connection. Note:
	 •	
Since the connector storage 
section does not have a suffi-
cient space, use a LAN cable 
that	does	not	exceed	the	sizes	
described in the illustrations.
 
z  Connect a LAN cable (category 5 or better, 
straight) between a PoE device (such as a 
hub) and the network connector of the cam-
era.
Important:
	 •	 Use	all	4	pairs	(8	pins)...

19
Connection example
PoE device (hub)
PCLAN cable
(category 5 or better, straight)
LAN cable
(category 5 or better, straight)LAN cable
(category 5 or better, straight)

LAN cable (category 5 or better, straight)
Important:
	 •	 A	PoE	hub	is	required.
  

20
Installation
Camera mounting
Installation shall be conducted after turning off each device. 
z  Remove the dome cover. (☞ Page 15)
x  Connect the cables to the camera. (☞ Pages 18 and 19)
c  Fix the camera with 3 screws (M4) (locally procured).
■ Ceiling■ Wall
Important:
	 •	 Do	not	touch	the	lens.	
	 •	 When	tightening	the	screws,	be	careful	to	ensure	that	the	cables	does	not	tangle	the	cables.