Panasonic Network Camera Wv Sp508 Wv Sp509 Installation Guide

21
Installation
Connect the safety wire
The following is an example of safety wire connection.
IMPORTANT:
  •  Be sure to install the safety wire. Ask your dealer for installation. 
 
For mounting on ceiling 
z  Remove the tripod mount base on the top 
of the camera. 
x  Align the tripod mount base with the safety 
wire plate for ceiling (accessory) and attach 
them to the camera with the mounting 
screws. 
IMPORTANT:
  • Use the detached mounting screws to attach the tripod mount base. When using...

22
Wire engaging holeSafety wire (accessory)
For mounting on wall
z  Put the tripod mount base on the bottom of the camera. 
    Secure the safety wire lug for wall (accessory) to the camera mount screw hole with the wire 
lug fixing screw (accessory).
IMPORTANT:
  •  Be sure to use the provided fixing screws 
for the safety wire lug and the removed 
screws for the camera mount base.
    When using different length screws, it may 
damage the camera or cause the camera 
to fall. 
    (Recommended...

23
Camera mounting
The camera is mounted on the camera mount bracket (locally procured) and the safety wire is 
secured. 
IMPORTANT:
  •  The installation area shall be strong enough to hold the camera and camera mount bracket. 
  •  The camera mount bracket (locally procured) shall be mounted on the foundation part of the 
construction or a part with adequate strength. 
  •  To prevent the mounting strength from becoming lower, do not use wooden screws to secure 
the camera mount bracket (locally...

24
Safety wireSafety wire
Recommended screw M6
Minimum pull-out strength
196 N {44.06 lbf}
Foundation part of 
construction or part 
with adequate strength
IMPORTANT:
  •  The safety wire shall be adjusted to remove slack.
  •  Be sure to install the safety wire to prevent a fall of the camera resulting in injury or accidents in 
case the camera comes off.
  •  To prevent the mounting strength from becoming lower, do not use wooden screws to secure 
the safety wire....

25
Connection
Caution:
  • ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED 
POWER SOURCE (IEC/EN/UL/CSA 60950-1). 
Before starting the connection, turn off the power of this camera and the devices to be connected. 
Before start the connection, prepare the required devices and cables.
z  Connect the RCA pin cable to the monitor 
output connector for adjustment on the 
rear (only for adjustment of the angle field 
of view).
   
IMPORTANT:
  •  The monitor output connector is provided...

26
v  Connect external devices to the EXT I/O terminal.
   When connecting an external device, remove 9 mm - 10 mm 
{11/32 inches - 13/32 inches} of the outer jacket of the cable 
and twist the cable core to prevent the short circuit first.
Specification of cable (wire):  22 AWG - 28 AWG
Single core, twisted
  •  Check whether the stripped part of the wire is not exposed and is securely connected. 
4  3  2  1
r GND
e AUX OUT
w ALARM OUT q ALARM IN

IMPORTANT:
  •  Do not connect 2 wires or more directly...

27
n  Connect the power supply. 
IMPORTANT:
  •  The 12 V DC power supply shall be insulated from the commercial AC power.
  •  The operating sound might be heard when the power is turned on, however it does not indi-
cate any malfunction. 
When using 12 V DC power supply*
 q  Loosen the screw of the power cord plug (accessory).
 w  Connect the cable of the 12 V DC power supply* to the 
power cord plug. 
    Strip 3 mm to 7 mm {1/8 inches to 9/32 inches} from the 
end of the wire, and twist the stripped...

28
When using PoE (IEEE802.3af compliant)
Connect a LAN cable (category 5 or better, straight, STP*) between a PoE device (such as a hub) 
and the network connector of the camera. 
* For Europe.
IMPORTANT:
  •  Use all 4 pairs (8 pins) of the LAN cable.
  •  The maximum cable length is 100 m {328 feet}.
  •  Make sure that the PoE device in use is compliant with IEEE802.3af standard.
  •  When connecting both the 12 V DC power supply and the PoE device for power supply, 12 V 
DC will be used for power...

29
Configure the network settings
Configuring the camera so that it can be accessed from a PC
The following are descriptions for when the camera with default settings is configured. If you 
are using firewall software on your PC, the Setup Program may not be able to find any 
cameras on your network. Configure the setting of the camera after temporarily invalidating 
the firewall software. Contact the network administrator or your Internet service provider for 
information about configuring the settings...

30
c  Select the camera you want to configure, and click [Access Camera].
Note: 
 • When cameras are displayed in [Panasonic IP Setting] screen, click the camera with same 
MAC address as the MAC address printed on the camera that you want to configure.
v  If the installation screen of the viewer software “Network Camera View 4S” is displayed, follow 
the instructions of the wizard to start the installation. (The viewer software is installed from the 
camera.)
  •  The “Live” page will be displayed.
  •...