Panasonic Network Camera Wv Sp508 Wv Sp509 Installation Guide

11
Precautions
Refer installation work to the dealer.
Installation work requires technique and experi-
ences. Failure to observe this may cause fire, 
electric shock, injury, or damage to the prod-
uct.
Be sure to consult the dealer.
Stop the operation immediately when 
something is wrong with this product.
When smoke goes up from the product, the 
smell of smoke comes from the product, or the 
exterior of the product has deteriorated, con-
tinued use will cause a fire or fall of the product 
resulting...

12
Do not rub the edges of metal parts with 
your hand.
Failure to observe this may cause injury.
Do not touch this product, the power cable 
or the connected cables during thunder. 
(Including during installation work)
Failure to observe this may cause electric shock.
Keep SDXC/SDHC/SD memory cards 
(option) away from infants and children.
Otherwise, they may swallow the cards by mis-
take.
In this case, consult a doctor immediately.
Do not damage the power cable.
Do not damage, fabricate, twist,...

13
data on the SD memory card will be delet-
ed when formatted.
    If an unformatted SD memory card or an 
SD memory card formatted with other 
devices is used, this product may not work 
properly or performance deterioration may 
be caused. Refer to the Operating 
Instructions (included in the CD-ROM) for 
how to format a SD memory card. 
  • When some SD memory cards are used 
with this product, the product may not 
work properly or performance deterioration 
may be caused. 
Code label
The code labels...

14
Precautions for Installation
This camera is designed to be used 
indoors.
This camera is not operable outdoors.
Do not expose this camera to direct sunlight for 
hours and do not install the product near a 
heater or an air conditioner. Otherwise, it may 
cause deformation, discoloration and malfunc-
tion. Keep this camera away from water and 
moisture. 
Installation place
Contact your dealer for assistance if you are 
unsure of an appropriate place in your particu-
lar environment.
  • Make sure that...

15
Screw tightening
  • The screws and bolts must be tightened 
with an appropriate tightening torque 
according to the material and strength of 
the installation area.
  • Do not use an impact driver. Use of an 
impact driver may damage the screws or 
cause tightening excessively.
  • When a screw is tightened, make the 
screw at a right angle to the surface. After 
tightening the screws or bolts, perform 
visual check to ensure tightening is enough 
and there is no backlash.
Fall prevention measures...

16
Major operating controls

W
Lens (option) ALC lens connector
ABF
W
ABF
SDCARD LOCK
W
Slide cover
Auto back focus button (ABF)Clamp for SD memory card
SD memory card slot
Tripod mount base

Tripod mount base 

17

About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes 
after releasing the button. The camera will start up and the settings including the network settings 
will be initialized. Do not turn off the power of the camera during the process of the initialization. 
Before initializing the settings, it is recommended to write down...

18
Lens mounting
Slowly rotate the lens clockwise to mount the lens and connect the lens cable to the ALC lens con-
nector of the camera. 
Optional dedicated lens
 Product name  Model number
  ALC lens for 1/3 type CCD cameras  WV-LZA62/2
  2x varifocal  (High resolution)
  *  If a lens for 1/3 type video camera other than the above is mounted and the camera is used at 
resolution of 1280 x 720 or higher, the camera cannot achieve full performance of high resolu-
tion. It is recommended to use a...

19
Note:
  •  The most common use of a varifocal lens and a zoom lens
    Note that the adjustment method is different depending on the type. For further information, 
    refer to the operating instructions for the lens to be used.
    When using 8x or 10x lens, adjust the back focus after positioning the zoom ring at the W 
end and positioning the focus ring at a step short of the F end.
    When using 2x or 3x lens, adjust the back focus after positioning the zoom ring at the T end 
and positioning...

20
Insert/remove a SD memory card (WV-SP509 only)
IMPORTANT:
  •  When inserting a SD memory card, make sure the direction.
  •  Before removing the SD memory card, make sure to select “Not use” for “SD memory card” on 
the [SD memory card] tab of the “Basic” page on the setup menu first. (☞ Operating 
Instructions (included in the CD-ROM))
 
z  Open the slide cover on the side of the camera, and then insert a SD memory card into the SD 
memory card slot.
x If necessary, loosen the screw of the clamp for...