Panasonic Network Camera Wv Sp302 Wv Sp305 Wv Sp306 Installation Guide

21
Installation
Connect the safety wire
The following is an example of safety wire connection.Important:
	 •	 Be	sure	to	install	the	safety	wire.	Ask	your	dealer	for	installation.	
 
For mounting on ceiling 
z  Remove  the  tripod  mount  base  on  the  top 
of the camera. 
x  Align the tripod mount base with the safety 
wire plate for ceiling (accessory) and attach 
them  to  the  camera  with  the  mounting 
screws. 
Important:
	 •	 Use	 the	detached	 mounting	screws	to	attach	 the	tripod	 mount	 base....

22
Wire engaging holeSafety wir
e
For mounting on wall
z Put the tripod mount base on the bottom of the camera. 
    Secure  the  safety  wire  lug  for  wall  (accessory)  to  the  camera  mount  screw  hole  with  the  wire 
lug fixing screw (accessory).
Important:
	 •	 Be	 sure	to	use	 the	provided	 fixing	screws	
for  the  safety  wire  lug  and  the  removed 
screws for the camera mount base.
    When  using  different  length  screws,  it  may 
damage  the  camera  or  cause  the  camera 
to fall....

23
Camera mounting
The camera is mounted on the camera mount bracket and the safety wire is secured. Important:
	 •	 The	installation	area	shall	be	strong	enough	to	hold	the	camera	and	camera	mount	bracket.	
	 •	 The	 camera	mount	bracket	 shall	be	mounted	 on	the	 foundation	 part	of	the	 construction	 or	a	
part with adequate strength. 
	 •	 To	 prevent	 the	mounting	 strength	from	becoming	 lower,	do	not	 use	 wooden	 screws	to	secure	
the camera mount bracket. 
 
z  Secure  the  camera  mount...

24
x Put  the  connection  hook  of  the  safety  wire  on  the  safety  wire  plate  or  the  safety  wire  lug 
secured on the foundation part of the construction or a part with adequate st\
rength. 
Important:
	 •	 The	safety	wire	shall	be	adjusted	to	remove	slack.	
 




Connection hook
Connection hook
Camer a mount br acket
Foundation part of construction 
or part with adequate strength
Safety wire plate
Safety wire
Safety wire
Safety wire
Recommended screw M6
Minimum pull-out strength
196 N {44.06...

25
Connection
Caution:
	 •	 FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	CLASS	2	POWER	SUPPLY.	
Before starting the connection, turn off the power of this camera and the devices to be connected. 
Before start the connection, prepare the required devices and cables.
z Connect  the  RCA  pin  cable  to  the  monitor 
output  connector  for  adjustment  on  the 
rear  (only  for  adjustment  of  the  angle  field 
of view).
    
Important:
	 •	 The	 monitor	output	connector	 is	provided	
only for checking...

26
v Connect external devices to the EXT I/O terminal.
    When  connecting  an  external  device,  remove  9  mm  -  10  mm 
{11/32  inches  -  13/32  inches}  of  the  outer  jacket  of  the  cable 
and twist the cable core to prevent the short circuit first.
Specification of cable (wire): 22 AWG - 28 AWG
    Single core, twisted
	 •	 Check	 whether	the	stripped	 part	of	the	
wire  is  not  exposed  and  is  securely  con-
nected. 
  * DAY/NIGHT IN is only for WV-SP306.
Important:
	 •	 Do	 not	connect...

27
When using 12 V DC power supply*
 q  Loosen the screw of the power cord plug (accessory).
  w  Connect  the  cable  of  the  12  V  DC  power  supply*  to  the 
power cord plug. 
    Strip 3 mm to 7 mm {1/8 inches to 9/32 inches} from the 
end  of  the  wire,  and  twist  the  stripped  part  of  the  wire 
sufficiently to avoid short circuit. 
Specification  of  cable  (wire):  16  AWG  -  24  AWG,  Single core, twisted
	 •	 Check	 whether	the	stripped	 part	of	the	 wire	 is	not	
exposed and is...

28
Connection example when connecting to a network using a 
PoE hub

LAN cable (category 5 or better, straight, STP*)
* PAL models onlyImportant:
	 •	 The	 video	monitor	 is	used	 for	checking	 the	adjustment	 of	the	 angular	 field	of	view	 when	 install-
ing the camera or when servicing. It is not provided for recording/ monitoring use.
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.
	 •	 Power	 supply	is	required	 for	each	 network	 camera.	 When	using	a	PoE	 device...

29
Configure the network settings
Install the software
Before installing the software, read the readme file on the provided CD-ROM first.
Software included on the provided CD-ROM
	 •	 Panasonic	IP	setting	software
   Configure the network settings of the camera. Refer to the following for further\
 information.
	 •	 Viewer	Software	"Network	Camera	View	4"
    It  is  necessary  to  install  the  viewer  software  "Network  Camera  View  4"  to  display  images  on  a 
PC.  Install  the...

30
z Start  the  Panasonic  IP  setting  software  by  double-clicking  the  "EasyIpSetup.exe"  icon  on  the 
provided CD-ROM.
x Click  the  [IP  setting]  button  after  selecting  the 
MAC  address/IP  address  of  the  camera  to  be 
configured.
Note:
	 •	 When	 using	a	DHCP	 server,	 the	IP	address	
assigned  to  the  camera  can  be  displayed  by 
clicking  the  [Refresh]  button  of  the  IP  setting 
software.
	 •	 When	 a	duplicate	 IP	address	 is	used,	 the	corre-
sponding  MAC...