Panasonic Network Camera Wv Sp302 Wv Sp305 Wv Sp306 Installation Guide

11
Precautions
Refer installation work to the dealer.
Installation work requires technique and experi-
ences.  Failure  to  observe  this  may  cause  fire, 
electric  shock,  injury,  or  damage  to  the  prod-
uct.
Be sure to consult the dealer.
Stop the operation immediately when 
something is wrong with this product.
When  smoke  goes  up  from  this  product  or  the 
smell  of  smoke  comes  from  this  product,  stop 
the  operation  immediately  and  contact  your 
dealer.
Turn  the  power  off...

12
Turn the power off when do wiring of this 
product.
Failure  to  observe  this  may  cause  electric 
shock.
In  addition,  short  circuit  or  wrong  wiring  may 
cause fire.
Turn the power off when cleaning of this 
product.
Failure to observe this may cause injury. 
[Precautions for use]
This system is designed to be used 
indoors. This product is not operable out-
doors.
This product has no power switch.
When  turning  off  the  power,  turn  off  a  circuit 
breaker.
To keep on using with stable...

13
	 •	 When	some	SDHC/SD	 memory	cards	are	
used  with  this  product,  the  product  may 
not  work  properly  or  performance  deterio-
ration  may  be  caused.Use  the  SDHC/SD 
memory cards recommended in page 34.
Code label
The  code  labels  (accessory)  are  required  at 
inquiry  for  trouble.  Use  caution  not  to  lose 
these  labels.  It  is  recommended  to  paste  one 
of the labels onto the CD-ROM case.
About the MOS image sensor
	 •	 When	 continuously	 shooting	a	bright	 light	
source...

14
Precautions for Installation
This camera is designed to be used 
indoors.
This camera is not operable outdoors.
Do not expose this camera to direct sunlight for 
hours  and  do  not  install  the  product  near  a 
heater  or  an  air  conditioner.  Otherwise,  it  may 
cause  deformation,  discoloration  and  malfunc-
tion.  Keep  this  camera  away  from  water  and 
moisture. 
Installation place
Do not place the unit in the following places:
	 •	 Locations	where	it	may	 get	wet	 from	 rain	
or...

15
Angle adjustment
Be  sure  to  loosen  the  screw  of  this  product 
mount  bracket  when  the  camera  angle  is 
adjusted. If the camera angle is changed when 
the  screw  is  tight,  excessive  force  is  applied  to 
the  camera  mount  bracket  and  camera,  and 
accordingly  they  may  be  damaged.  Be  sure  to 
tighten  the  screw  securely  after  camera  angle 
adjustment.
Radio disturbance
When this product is used near TV/radio anten-
na, strong electric field or magnetic field (near a...

16
Major operating controls


About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes 
after  releasing  the  button.  The  camera  will  start  up  and  the  settings  including  the  network  settings 
will  be  initialized.  Before  initializing  the  settings,  it  is  recommended  to  write  down  the  settings  in 
advance.
W...

17
Lens mounting
Slowly rotate the lens clockwise to mount the lens and connect the lens cable to the ALC lens con-
nector of the camera. Important: 
SP305SP302
	 •	 It	is	impossible	to	use	lenses	without	the	focus	adjustment	function	or	zoom	lenses.
Optional dedicated lens
  Product name  Model number
  ALC lens for 1/3 type CCD cameras  WV-LZA62/2
  2x vari-focal   (High resolution)
  * If a lens for 1/3  type video camera other than the above is mounted and the camera is used at 
resolution of  1280 x...

18
Note:
	 •	 The	most	common	use	of	a	varifocal	lens	and	a	zoom	lens	
    Note  that  the  adjustment  method  is  different  depending  on  the  type.  For  further  information, 
refer to the operating instructions for the lens to be used. 
    Adjust  the  back  focus  after  positioning  the  zoom  ring  at  the  "T"  end  and  positioning  the  focus 
ring at a step short of the "F" end.
	 •	 Depending	 on	the	 lens	 to	be	 used,	 if	the	 zoom	 ring	is	fully	 rotated	 in	the...

19
 x Fasten the zoom lock knob.
 
c  Press the focus assist button.
  → "FOCUS ADJUSTMENT" menu will be displayed.
    The focus assist function will be activated to perform the optimum adjus\
tment.
 
v  When  the  focus  ring  is  positioned  near  the  best  focus  position,  the  position  will  automatically 
be memorized as the "PEAK HOLD" position.
 
b  When  the  focus  ring  is  moved,  the  current  focus  position  will  be  indicated  on  "INDICATOR" 
Adjust the focus...

20
Insert/remove an SDHC/SD memory card
Important:
	 •	 Before	inserting	an	SDHC/SD	memory	card,	turn	off	the	power	of	the	camera	first.
	 •	 When	inserting	an	SDHC/SD	memory	card,	make	sure	the	direction.
	 •	 Before	 removing	the	SDHC/SD	 memory	card,	select	 "Not	use"	for	"About	 SD	memory	 card"	on	
the [SD memory card] tab of "Basic" on the setup menu first. Turn off the power after "Not use" 
selection,  and  then  unload  the  SDHC/SD  memory  card.  When  the...