Panasonic Network Camera Wv Sf548 Installation Guide

21
Installing the camera directly on the ceiling or wall
Place the installation template label (accessory) on the ceiling or wa\
ll, and make a hole to pass the 
cable.
Remove the template label, and mount the camera by fixing 4 screws (locally procured). 
(☞ Page 29)
20 mm {13/16 inches}83.5 mm {3-5/16 inches}
Cable access hole for ceiling/wall
Recommended screw (M4: 4 pcs.)
Side cable access hole
Direction marker for installation
Screws 
(locally procured)
Installation template label (accessory)
46 mm...

22
Insert/remove an SD memory card (WV-SF549/WV-SF539 only)
IMPORTANT:
	 •	 Before	inserting	the	SD	memory	card,	turn	off 	the	power	of	the	camera	first.	
	 •	 When	inserting	an	SD	memory	card,	make	sure	the	direction.	
	 •	 Before	 removing	 the	 SD	 memory	 card,	 select	 "Not	 use"	 for	 "SD	 memory	 card"	 on	 the	 [SD	 memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and then 
unload the SD memory card. When the SD memory card is...

23
Connection
Before starting the connection, turn off the power of this camera and the devices to be connected. 
Check and prepare the required devices and cables for connection. Note:
	 •	 Since	 the	 connector	 storage	 section does not have a suffi-
cient space, use audio cables 
and a LAN cable that do not 
exceed the sizes described in 
the illustrations.
 
z Connect the RCA pin cable to the monitor out connector for adjustment (\
only used for adjust-
ment of the angular field of view)....

24
c Connect an external speaker with amplifier to 
the audio output connector (for use of the audio 
transmission function). 
SF549 SF539
  Connect a stereo mini plug (ø3.5 mm) (audio 
output is monaural). 
	 •	 Recommended	cable	length:	10	m	  {33 feet} or less
v Connect the cables of external devices to the 
EXT I/O terminal plug (accessory). 
  q  When connecting an external device, remove 
8 mm - 9 mm {5/16 inches - 11/32 inches} of 
the outer jacket of the cable and twist the cable 
core to prevent...

25
 e  After the cable connection, connect the exter -
nal I/O terminal plug to the external I/O termi-
nals of the camera. 
     IMPORTANT:
	 •	 Do	not	connect	2	wires	or	more	directly	to	a	terminal.	When	it	is	necessary	to	connect	2	wires	 or more, use a splitter.
	 •	 Input	 and	 output	 of	 the	 EXT	 I/O	 terminal	 2	 and	 3	 can	 be	 switched	 by	 configuring	 the	 setting.	 "Off" is selected by default. It is possible to determine whether or not to\
 receive input from EXT 
I/O terminal 2...

26
When using 12 V DC power supply*
 q   Loosen the screws of the power cord plug 
(accessory). 
  w  Connect the cable of the 12 V DC power sup-
ply* to the power cord plug.
   Strip 3 mm - 7 mm {1/8 inches - 9/32 inches} 
from the end of the wire, and twist the stripped 
part of the wire sufficiently to avoid short circuit. 
Specification of cable (wire):  
16 AWG - 24 AWG, Single core, twisted
	 •	 Check	 whether	 the	 stripped	 part	 of	 the	 wire	 is	 not exposed and is securely connected.
  e...

27
When using PoE (IEEE802.3af compliant)
Connect a LAN cable (category 5 or better, straight, STP*) between a PoE device (such as a hub) 
and the network connector of the camera.
* E models onlyIMPORTANT:
	 •	 Use	all	4	pairs	(8	pins)	of	the	LAN	cable.	
	 •	 The	maximum	cable	length	is	100	m	{328	feet}.	
	 •	 Make	sure	that	the	PoE	device	in	use	is	compliant	with	IEEE802.3af	standard.	
	 •	 When	 connecting	both	the	12	V	DC	power	supply	and	the	PoE	device	for	power	supply,	12	V	 DC will be used for...

28
Connection example when connecting to a network using a 
PoE hub
PoE device (hub)
PCMicrophone (option)
Microphone (option)
Speaker with amplier 
(option)
Speaker with amplier 
(option)Video monitor (for adjustment use only)Video monitor 
(for adjustment use only)
LAN cable (category 5 or 
better, straight, STP*) LAN cable (category 5 or 
better, straight, STP*)
LAN cable (category 5 or 
better, straight, STP*)

LAN cable (category 5 or better, straight, STP*)
* E models only IMPORTANT:
	 •	 The	video...

29
Installation
Camera mounting
Installation shall be conducted after turning off each device. 
z  Detach the dome cover. (☞ Page 17)
x  Connect the cables to the camera. (☞ Pages 23 - 28)
  As necessary, use a cable tie (accessory) to assemble the cables.
c  Mount the camera. (The illustration represents the case in which a two-gang junction box is 
installed.)
   Fix the camera with 4 screws (M4, locally procured).
Direction marker for installation
(gTOP)
Direction marker for installation
(FRONTh)...

30
Adjustment
z Adjust the camera angle. When determining the camera angle, repeat fine adjustments by 
gradually moving the panning table, tilting table, and azimuth adjustmen\
t ring. 
Horizontal position (Panning)
Loosen the panning lock screw, rotate 
the panning table to adjust the pan 
direction. (Adjustable range: 350 °)
Panning is possible within the range 
of 180 ° (when panning clockwise) 
and 170 ° (when panning counter -
clockwise). After adjustment, tighten 
the panning lock screw to fix the...