Panasonic Network Camera Wv Sf548 Installation Guide

31
Vertical position (Tilting)
Loosen the tilting lock screws (x2), and rotate 
the tilting table to adjust the tilting direction. 
(Adjustable	range:	±75	°)	Since	a	variable	focal	
lens is used, it is possible to change the angu-
lar field of view. This lens can also be rotated in 
the reverse direction, but the image azimuth is 
reversed. In this case, hold down the auto 
focus (AF) button/upside-down button for 5 
seconds or more. The upside-down function 
starts operating and the image azimuth is...

32
x  Adjust the angular field of view and the focus. 
  Adjust the angular field of view in accordance with the distance between the camera lens and a 
photographic subject. These adjustments shall be performed together with\
 the camera angle 
adjustment.
Zoom lock knob
Loosen TightenFocus ring
* Do not move the focus ring.
Auto focus (AF) button/Upside-down button
 q  Loosen the zoom lock knob and move the knob between TELE and WIDE to obt\
ain the appro-
priate angle of view.
  w  Press the auto...

33
Note:
	 •	 If	 the	 zoom	 lock	 knob	 is	 fully	 turned	 in	 the	 "W"	 direction,	 the	 periphery	 may	 become	 dark.	 In	 such a case, turn the zoom lock knob in the "T" direction for readjustment.
	 •	 If	 the	 zoom	 lock	 knob	 is	 slightly	 tightened	 before	 the	 zoom	 is	 adjusted,	 the	 knob	 will	 become	 stable, making fine adjustments easier to perform.
	 •	 When	 shooting	 in	 the	 following	 place	 or	 the	 following	 subjects,	 focus	 may	 not	 be	 adjusted	 automatically....

34
Attaching the dome cover
FRONT 
TOP
MONITOROUTLOCK
Auto focus (AF)
button
Attach the dome cover to the camera. SF549 SF548
The following procedure is required when using WV-SF549 or WV-SF548. Refer to page 35 when 
using WV-SF539 or WV-SF538. 
    
z  Attach the inner dome to the camera in the 
same manner as the procedure in page 30. 
  Make sure that the tilting lock screws of 
the camera and the holes on the inner 
dome are correctly fit together. 
x Attach the dome cover using the bit for...

35
z Align the indication "OPEN" to the marker 
of the camera to attach the dome cover. 
x Remove the cover film from the dome 
cover except the dome section.
c  Adjust the direction of the inner dome. 
  Rotate the dome cover clockwise to adjust 
the marker to "ADJUST". The clear dome 
and the inner dome can rotate together in 
this state. Rotate the dome section of the 
dome cover to adjust the direction so that 
no eclipse may be caused.
    
ADJUSTOPENLOCK
Marker
Dome 
cover
Dome...

36
v  Rotate the dome cover clockwise to adjust the marker to "LOCK". 
b Fix the dome cover and the camera with 
the dome cover fixing screw (M3, step 
screw, x1) that has been removed in the 
procedure of "Detaching the dome cover" 
(☞ page 17).
   (Recommended tightening torque:  
0.59  N·m {0.44 lbf·ft})
n After the installation is complete, remove 
the cover film, which was removed halfway 
in Step 2, completely from the dome sec-
tion.
m Push down the auto focus (AF) button with 
a...

37
Using the CD-ROM
About the CD launcher
Insert the provided CD-ROM into the CD-ROM drive of your PC to start up the CD launch\
er. Then the 
License Agreement will be displayed.
	 •	 If	 the	launcher	 window	is	not	 displayed,	 double	click	the	"CDLauncher.exe"	 file	on	the	 CD-ROM.
	 •	 Read  the	Agreement	 and	choose	 "I	accept	 the	term	 in	the	 license	 agreement",	 and	click	 [OK].	
Then	 the	launcher window will be displayed.
Using	the	supplied	CD-ROM,	the	following	actions	can	be...

38
Installing Panasonic IP setting software
On	the	 CD	 launcher	 window,	click	the	[Install]	 button	next	to	[IP	 Setting	 Software]	 to	display	 the	Panasonic 	
IP	 setting	 software	 installation	 window.	Confirm	the	following	 settings	before	starting	 the	installation.
 q Select	the	Panasonic	IP	setting	software	to	install.
 w Select	 where	 to	 create	 the	 Panasonic	 IP	 setting	 shortcut	 icon	 when	 the	 Panasonic	 IP	 setting	 software is installed.
 e Specify	which	folder	on	the	PC	to	install...

39
Installing the manuals
On	the	CD	launcher	window,	click	the	[Install]	button	next	to	[Manual]	to	display	the	Manual	installa-tion	window.	Confirm	the	following	settings	before	starting	the	installation.
q
r e
w
t
 q Select	which	manuals	to	install.	The	camera	models	that	the	manuals	support	 are	displayed	in	
w	"Model	List".
 w The	camera	models	that	are 	supported	by	the	manuals	selected	in	q	are 	displayed	here.
 e Select	where	to	create	the	manuals	shortcut	icon	when	the	manuals	are...

40
Configure the network settings of the camera using the 
Panasonic IP setting software
It	is	possible	to	perform	the	network	settings	of	the	camera	using	the	IP	setup	software	on	the	pro-
vided	 CD-ROM.	 When	 using	 multiple	 cameras,	 it	 is	 necessary	 to	 configure	 the	 network	 settings	 of	 each	camera	independently.	
If	 the	 Panasonic	 IP	 setting	 software	 does	 not	 work,	 configure	 the	 network	 settings	 of	 the	 camera	and	 the	 PC	 individually	 on	 the	 "Network"	 page	 of...